介绍以P87LPC764型单片机为核心的延时型漏电继电器设计方案。该方案可供用户选择实现额定动作电流和5倍额定动作电流下不同的延时动作时间，并有重合闸设定选择功能。解决了以往传统分立元件带来的延时时间离散性大且不易实现的弊端。 Abstract: In this paper, the delay leakage relay based on P87LPC764 is introduced in detail. This system provides different relay times at rating current and 5× rating current for users and also offers superposition brake set selection function. So that it resolves many traditional problems.
上传时间： 2013-11-08
上传用户：zhaiye
The PCF8578 is a low power CMOS1 LCD row and column driver, designed to drive dotmatrix graphic displays at multiplex rates of 1:8, 1:16, 1:24 or 1:32. The device has40 outputs, of which 24 are programmable and configurable for the following ratios ofrows/columns: 32¤8, 24¤16, 16¤24 or 8¤32. The PCF8578 can function as a stand-alone LCDcontroller and driver for use in small systems. For larger systems it can be used inconjunction with up to 32 PCF8579s for which it has been optimized. Together these twodevices form a general purpose LCD dot matrix driver chip set, capable of driving displaysof up to 40960 dots. The PCF8578 is compatible with most microcontrollers andcommunicates via a two-line bidirectional bus (I2C-bus). Communication overhead isminimized by a display RAM with auto-incremented addressing and display bankswitching.
上传时间： 2013-10-23
上传用户：顶得柱
1 FEATURES· Single chip LCD controller/driver· 1 or 2-line display of up to 24 characters per line, or2 or 4 lines of up to 12 characters per line· 5 ′ 7 character format plus cursor; 5 ′ 8 for kana(Japanese syllabary) and user defined symbols· On-chip:– generation of LCD supply voltage (external supplyalso possible)– generation of intermediate LCD bias voltages– oscillator requires no external components (externalclock also possible)· Display data RAM: 80 characters· Character generator ROM: 240 characters· Character generator RAM: 16 characters· 4 or 8-bit parallel bus or 2-wire I2C-bus interface· CMOS/TTL compatible· 32 row, 60 column outputs· MUX rates 1 : 32 and 1 : 16· Uses common 11 code instruction set· Logic supply voltage range, VDD - VSS: 2.5 to 6 V· Display supply voltage range, VDD - VLCD: 3.5 to 9 V· Low power consumption· I2C-bus address: 011101 SA0.
上传时间： 2013-11-08
上传用户：laozhanshi111
The bootloader is stored in the internal boot ROM memory (system memory) of STM32devices. It is programmed by ST during production. Its main task is to download theapplication program to the internal Flash memory through one of the available serialperipherals (USART, CAN, USB, etc.). A communication protocol is defined for each serialinterface, with a compatible command set and sequences
上传时间： 2014-09-06
上传用户：417313137
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
MPLAB C30用户指南(英文) HIGHLIGHTSThe information covered in this chapter is as follows:• About this Guide• Recommended Reading• Troubleshooting• The Microchip Web Site• Development Systems Customer Notification Service• Customer Support Document LayoutThe document layout is as follows:• Chapter 1: Compiler Overview – describes MPLAB C30, development tools andfeature set.• Chapter 2: Differences between MPLAB C30 and ANSI C – describes thedifferences between the C language supported by MPLAB C30 syntax and thestandard ANSI-89 C.• Chapter 3: Using MPLAB C30 – describes how to use the MPLAB C30 compilerfrom the command line.• Chapter 4: MPLAB C30 Runtime Environment – describes the MPLAB C30runtime model, including information on sections, initialization, memory models, thesoftware stack and much more.• Chapter 5: Data Types – describes MPLAB C30 integer, floating point and pointerdata types.• Chapter 6: Device Support Files – describes the MPLAB C30 header and registerdefinition files, as well as how to use with SFR’s.• Chapter 7: Interrupts – describes how to use interrupts.• Chapter 8: Mixing Assembly Language and C Modules – provides guidelines tousing MPLAB C30 with MPLAB ASM30 assembly language modules.
上传时间： 2013-10-21
上传用户：13925096126
PICKIT™ 2 PROGRAMMER-TO-GO USER GUIDE The PICkit 2 Programmer-To-Go functionality allows a PIC MCU memory image to be downloaded into the PICkit 2 unit for later programming into a specific PIC MCU. No software or PC is required to program devices once the PICkit 2 unit is set up for Programming-To-Go. A USB power source for the PICkit 2 is all that is needed.
标签： PROGRAMMER-TO PICKIT 8482
上传时间： 2013-10-29
上传用户：ca05991270
基于AT89C52单片机的步进电机控制系统设计 摘 要: 提出了一个由AT89C52单片机控制步进电机的实例。可以通过键盘输入相关数据, 并根据需要, 实时对步进电机工作方式进行设置, 具有实时性和交互性的特点。该系统可应用于步进电机控制的大多数场合。实践表明, 系统性能优于传统的步进电机控制器。 关键词: 单片机; 步进电动机; 直流固态继电器; 实时控制 ABSTRACT: A stepp ing motor control system based on AT89C52 chip microcomputer was described.The data can be inputwith keyboard, and stepp ingmotorwas controlled by these data. According to the demand, users can set the workingmodel of stepp ingmotor in real2time. This system can be widely used in stepp ing motor controlling. The p ractice showed that the performance of this system outdid the tradi-tional stepp ing motor controller.
上传时间： 2013-11-22
上传用户：vodssv
Keil C51使用详解Keil C51 是美国Keil Software 公司出品的51 系列兼容单片机C 语言软件开发系统，与汇编相比，C 语言在功能上、结构性、可读性、可维护性上有明显的优势，因而易学易用。用过汇编语言后再使用C 来开发，体会更加深刻。Keil C51 软件提供丰富的库函数和功能强大的集成开发调试工具，全Windows界面。另外重要的一点，只要看一下编译后生成的汇编代码，就能体会到Keil C51生成的目标代码效率非常之高，多数语句生成的汇编代码很紧凑，容易理解。在开发大型软件时更能体现高级语言的优势。下面详细介绍 Keil C51 开发系统各部分功能和使用。第二节 Keil C51 单片机软件开发系统的整体结构C51 工具包的整体结构，如图(1)所示，其中uVision 与Ishell 分别是C51 forWindows 和for Dos 的集成开发环境(IDE)，可以完成编辑、编译、连接、调试、仿真等整个开发流程。开发人员可用IDE 本身或其它编辑器编辑C 或汇编源文件。然后分别由C51 及A51 编译器编译生成目标文件(.OBJ)。目标文件可由LIB51 创建生成库文件，也可以与库文件一起经L51 连接定位生成绝对目标文件(.ABS)。ABS 文件由OH51 转换成标准的Hex 文件，以供调试器dScope51 或tScope51 使用进行源代码级调试，也可由仿真器使用直接对目标板进行调试，也可以直接写入程序存贮器如EPROM 中。图(1) C51 工具包整体结构图第三节 Keil C51 工具包的安装81. C51 for Dos在 Windows 下直接运行软件包中DOS\C51DOS.exe 然后选择安装目录即可。完毕后欲使系统正常工作须进行以下操作(设C:\C51 为安装目录)：修改 Autoexec.bat，加入path=C:\C51\BinSet C51LIB=C:\C51\LIBSet C51INC=C:\C51\INC然后运行Autoexec.bat2. C51 for Windows 的安装及注意事项：在 Windows 下运行软件包中WIN\Setup.exe，最好选择安装目录与C51 for Dos相同，这样设置最简单(设安装于C:\C51 目录下)。然后将软件包中crack 目录中的文件拷入C:\C51\Bin 目录下。第四节 Keil C51 工具包各部分功能及使用简介1. C51 与A51(1) C51C51 是C 语言编译器，其使用方法为：C51 sourcefile[编译控制指令]或者 C51 @ commandfile其中 sourcefile 为C 源文件(.C)。大量的编译控制指令完成C51 编译器的全部功能。包控C51 输出文件C.LST，.OBJ，.I 和.SRC 文件的控制。源文件(.C)的控制等，详见第五部分的具体介绍。而 Commandfile 为一个连接控制文件其内容包括：.C 源文件及各编译控制指令，它没有固定的名字，开发人员可根据自己的习惯指定，它适于用控制指令较多的场合。(2) A51A51 是汇编语言编译器，使用方法为：9A51 sourcefile[编译控制指令]或 A51 @ commandfile其中sourcefile 为汇编源文件(.asm或.a51)，而编译控制指令的使用与其它汇编如ASM语言类似，可参考其他汇编语言材料。Commandfile 同C51 中的Commandfile 类似，它使A51 使用和修改方便。2. L51 和BL51(1) L51L51 是Keil C51 软件包提供的连接/定位器，其功能是将编译生成的OBJ 文件与库文件连接定位生成绝对目标文件(.ABS)，其使用方法为：L51 目标文件列表[库文件列表] [to outputfile] [连接控制指令]或 L51 @Commandfile源程序的多个模块分别经 C51 与A51 编译后生成多个OBJ 文件，连接时，这些文件全列于目标文件列表中，作为输入文件，如果还需与库文件(.LiB)相连接，则库文件也必须列在其后。outputfile 为输文件名，缺少时为第一模块名，后缀为.ABS。连接控制指令提供了连接定位时的所有控制功能。Commandfile 为连接控制文件，其具体内容是包括了目标文件列表，库文件列表及输出文件、连接控制命令，以取代第一种繁琐的格式，由于目标模块库文件大多不止1 个，因而第2 种方法较多见，这个文件名字也可由使用者随意指定。(2) Bl51BL51 也是C51 软件包的连接/定位器，其具有L51 的所有功能，此外它还具有以下3 点特别之处：a. 可以连接定位大于64kBytes 的程序。b. 具有代码域及域切换功能(CodeBanking & Bank Switching)c. 可用于RTX51 操作系统RTX51 是一个实时多任务操作系统，它改变了传统的编程模式，甚至不必用main( )函数，单片机系统软件向RTOS 发展是一种趋势，这种趋势对于186 和38610及68K 系列CPU 更为明显和必须，对8051 因CPU 较为简单，程序结构等都不太复杂，RTX51 作用显得不太突出，其专业版软件PK51 软件包甚至不包括RTX51Full，而只有一个RTX51TINY 版本的RTOS。RTX51 TINY 适用于无外部RAM 的单片机系统，因而可用面很窄，在本文中不作介绍。Bank switching 技术因使用很少也不作介绍。3. DScope51，Tscope51 及Monitor51(1) dScope51dScope51 是一个源级调试器和模拟器，它可以调试由C51 编译器、A51 汇编器、PL/M-51 编译器及ASM－51 汇编器产生的程序。它不需目标板（for windows 也可通过mon51 接目标板），只能进行软件模拟，但其功能强大，可模拟CPU 及其外围器件，如内部串口，外部I/O 及定时器等，能对嵌入式软件功能进行有效测试。
上传时间： 2013-11-01
上传用户：zhouxuepeng1
虽然PIC都是8位的单片机，但都采用RISC（Reduced Instruction Set Computing）核心结构，这有别于过去一般的CISC(Complex Instruction Set Computing)结构。所谓RISC结构就是采用哈佛双总线结构，将地址总线与数据总线分开，因此在同一个指令执行过程中，数据与地址可以同时传送，避免了总线处理上的瓶颈。
上传时间： 2013-11-21
上传用户：tianyi223
