以S3C825A为例介绍三星公司SAM8系列单片机的内部结构及其软件开发环境，详细描述采用混合编程法来对SAM8系列单片机进行软件设计的一般方法，最后给出用混合编程法对S3C825A进行软件设计的具体应用实例。 Abstract: With S3C825A,this paper firstly introduces the SAM8 Series single-chip microcontrollers and their software development environment, then introduces mixed programming technology for SAM8 Series single-chip microcontrollers. In the end, the application program is also given.
上传时间： 2013-12-09
上传用户：ZZJ886
针对船舶气象仪保障维修而设计的船舶气象仪测试系统，包括信息处理终端、主仪器检测模块、传感器检测模块，各个模块都采用基于AVR单片机的嵌入式系统，模块之间通过CAN总线进行通信。结果表明，船舶气象仪测试系统能够快速检测船舶气象仪故障，与单纯依靠人工方式排查故障相比，故障检测时间缩短了60%以上。 Abstract: The test system of ship meteorological instrument was developed to satisfy the maintenance of ship meteorological instruments，which composed of information processing terminal， testing module of main instrument and testing module of sensors. Each of these modules included an embedded system based on microcontroller of AVR Series and communicated with other module by CAN bus. The results show that the test system can judge the fault of ship meteorological instrument quickly and shorten the fault detection time as much as 60% compared with simple manual troubleshooting.
上传时间： 2013-11-23
上传用户：stvnash
为了在工业生产及过程控制中准确测量温度，设计了一种基于低功耗MSP430单片机的数字温度计。整个系统通过单片机MSP430F1121A控制DS18B20读取温度，采用数码管显示，温度传感器DS18B20与单片机之间通过串口进行数据传输。MSP430系列单片机具有超低功耗，且外围的整合性高，DS18B20只需一个端口即可实现数据通信，连接方便。通过多次实验证明，该系统的测试结果与实际环境温度一致，除了具有接口电路简单、测量精度高、误差小、可靠性高等特点外，其低成本、低功耗的特点使其拥有更广阔的应用前景。 Abstract: In order to obtain accurate measuring temperature in industrial production and process control， a digital thermometer based on MSP430 MCU is designed. The system uses MSP430F1121A MCU to control DS18B20， and gets the temperature data， which is displayed on the LED. The temperature sensor DS18B20 and MCU transmit data through serial communication. MSP430 Series has ultra-low power and high integration， DS18B20 only needs one port to achieve data communication. Through many experimental results prove， this system is consistent with actual environment temperature. The system has characteristics of interface circuit simple， high measuring accuracy， minor error， high reliability， besides， the characteristics of low cost and low power make it having vaster application prospect.
上传时间： 2013-10-16
上传用户：wettetw
Bootloader是微处理器上电时运行的第一段代码，它可以通过通信接口实现对微处理器内部应用程序的更新升级，为网络化嵌入式产品的应用程序升级带来极大的便利。由于目前没有统一嵌入式系统的Bootloader。基于NEC 78K0系列单片机自编程原理，设计出一个适用于78K0/Fx2系列单片机的Bootloader，并能够通过单片机串口在线升级应用程序。 Abstract: Bootloader is the first piece of code executed after microprocessor startup. It makes the embedded product’s firmware update conveniently through communication interface. However， no unified bootloader is available for all kinds of microprocessor products. Based on the principle of self-programming NEC 78K0s’ Series， a useful Bootloader which is suitable for 78K0/Fx2s’ Series MCU is designed，the design can update the application through serial ports.
标签： Bootloader MCU 自编程
上传时间： 2013-10-26
上传用户：fang2010
TMS570LS系列数据手册(英) TMS570LS Series 16/32-BIT RISC Flash Microcontroller
上传时间： 2013-10-14
上传用户：tecman
The PAM2862 is a continuous mode inductivestep-down converter, designed for driving singleor multiple Series connected LEDs efficientlyfrom a voltage source higher than the LEDvoltage. The device operates from an inputupply between 6V and 30V and provides anexternally adjustable output current of up to 1A.Depending upon supply voltage and externalcomponents, this can provide up to 24 watts ofoutput power.
上传时间： 2013-11-16
上传用户：司令部正军级
The TL2575 and TL2575HV represent superior alternatives to popular three-terminal linear regulators. Due totheir high efficiency, the devices significantly reduce the size of the heatsink and, in many cases, no heatsink isrequired. Optimized for use with standard Series of inductors available from several different manufacturers, theTL2575 and TL2575HV greatly simplify the design of switch-mode power supplies by requiring a minimaladdition of only four to six external components for operation.
标签： STEP-DOWN SWITCHING SIMPLE 1A
上传时间： 2013-11-20
上传用户：jelenecheung
Although Stellaris microcontrollers have generous internal SRAM capabilities, certain applicationsmay have data storage requirements that exceed the 8 KB limit of the Stellaris LM3S8xx Seriesdevices. Since microcontrollers do not have an external parallel data-bus, serial memory optionsmust be considered. Until recently, the ubiquitous serial EEPROM/flash device was the only serialmemory solution. The major limitations of EEPROM and flash technology are slow write speed, slowerase times, and limited write/erase endurance.Recently, serial SRAM devices have become available as a solution for high-speed dataapplications. The N256S08xxHDA Series of devices, from AMI Semiconductor, offer 32 K x 8 bits oflow-power data storage, a fast Serial Peripheral Interface (SPI) serial bus, and unlimited write cycles.The parts are available in 8-pin SOIC and compact TSSOP packages.
上传时间： 2013-10-14
上传用户：cxl274287265
Designing Boards with Atmel AT89C51, AT89C52, AT89C1051, and AT89C2051 for Writing Flash at In-Circuit Test:Recent improvements in chips andtesters have made it possible for thetester to begin taking over the role traditionallyassigned to the PROM programmer.Instead of having a PROM programmerwrite nonvolatile memoriesbefore assembling the board, the in-circuittester writes them during in-circuittesting operations. Many Teradyne Z18-Series testers are now in use loadingcode into nonvolatile memories, microcontrollersand in-circuit programmable logic devices. The purpose of this note is to explain how the Z18 approaches the writing task for Atmel AT89C Series IC’s,so that designers of boards using these chips can get the best results.
标签： Designing Boards Atmel with
上传时间： 2013-11-20
上传用户：lijianyu172
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS Series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
