The SN65LBC170 and SN75LBC170 aremonolithic integrated circuits designed forbidirectional data communication on multipointbus-transmission lines. Potential applicationsinclude serial or parallel data transmission, cabledperipheral buses with twin axial, ribbon, ortwisted-pair cabling. These devices are suitablefor FAST-20 SCSI and can transmit or receivedata pulses as short as 25 ns, with skew lessthan 3 ns.These devices combine three 3-state differentialline drivers and three differential input linereceivers, all of which operate from a single 5-Vpower supply.The driver differential outputs and the receiverdifferential inputs are connected internally to formthree differential input/output (I/O) bus ports thatare designed to offer minimum loading to the buswhenever the driver is disabled or VCC = 0. Theseports feature a wide common-mode voltage rangemaking the device suitable for party-lineapplications over long cable runs.
上传时间： 2013-10-13
上传用户：ytulpx
The bootloader is stored in the internal boot ROM memory (system memory) of STM32devices. It is programmed by ST during production. Its main task is to download theapplication program to the internal Flash memory through one of the available serialperipherals (USART, CAN, USB, etc.). A communication protocol is defined for each serialinterface, with a compatible command set and sequences
上传时间： 2014-09-06
上传用户：417313137
FEATURES400 MSPS internal clock speedIntegrated 10-bit DAC32-bit tuning wordPhase noise ≤ –120 dBc/Hz @ 1 kHz offset (DAC output)Excellent dynamic performance>75 dB SFDR @ 160 MHz (±100 kHz offset) AOUTSerial I/O control1.8 V power supplySoftware and hardware controlled power-down48-lead TQFP/EP packageSupport for 5 V input levels on most digital inputsPLL REFCLK multiplier (4× to 20×)Internal oscillator; can be driven by a single crystalPhase modulation capabilityMultichip synchronization
上传时间： 2014-12-04
上传用户：axin881314
The MSP-FET430PIF is a Parallel Port interface (does not include target board) that is used to program and debug MSP430 FET tools and test boards through the JTAG interface. This interface is included in our FET tools, but sold without the development board. This interface uses a Parallel PC Port to communicate to the Debugger Software (IAR Kickstart software included) running on the PC. The interface uses the standard 14 pin header to communicate to the MSP430 device using the standard JTAG protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is extremely low power, no external power supply is required. The tool has an integrated software environment and connects directly to the PC which greatly simplifies the set-up and use of the tool. The flash development tool supports development with all MSP430 flash parts. Features MSP430 debugging interface to connect a MSP430-Flash-device to a Parallel port on a PC Supports JTAG debug protocol (NO support for Spy-Bi-Wire (2-wire JTAG) debug protocol, Spy-Bi-Wire (2-wire JTAG) is supported by MSP-FET430UIF) Parallel Port cable and a 14-conductor target cable Full documentation on CD ROM Integrated IAR Kickstart user interface which includes: Assembler Linker Limulator Source-level debugger Limited C-compiler Technical specifications: Backwardly compatable with existing FET tool boards.
上传时间： 2013-10-26
上传用户：fengweihao158@163.com
NEC 16位MCU参考手册 The 78K0R/IC3 is a 16-bit single-chip microcontroller that uses a 78K0R CPU core and incorporates peripheral functions, such as ROM/RAM, a multi-function timer, a multi-function serial interface, an A/D converter, a programmable gain amplifier (PGA), a comparator, a real-time counter, and a watchdog timer.
上传时间： 2013-11-02
上传用户：努力努力再努力
The CAT25128 is a 128−Kb Serial CMOS EEPROM device internally organized as 16Kx8 bits. This features a 64−byte page write buffer and supports the Serial Peripheral Interface (SPI) protocol. The device is enabled through a Chip Select (CS) input. In addition, the required bus signals are clock input (SCK), data input (SI) and data output (SO) lines. The HOLD input may be used to pause any serial communication with the CAT25128 device. The device featuressoftware and hardware write protection, including partial as well as full array protection.
上传时间： 2013-11-15
上传用户：fklinran
The CAT34C02 is a 2 kb Serial CMOS EEPROM, internallyorganized as 16 pages of 16 bytes each, for a total of 256 bytes of 8 bitseach.
上传时间： 2013-10-23
上传用户：ppeyou
CAT5110/18/19/23/24/25 linear-taper digitally programmable potentiometers perform the same function as a mechanical potentiometer or a variable resistor. These devices consist of a fixed resistor and a wiper contact with 32-tap points that are digitally controlled through a2-wire up/down serial interface.
上传时间： 2013-11-22
上传用户：541657925
HCS12微控制器MC9S12DP256 第一步： 1) HCS12 技术概述2) Operating Modes工作模式3) Resource Mapping资源映射4) External Bus Interface外部总线接口5) Port Integration Module端口集成模块6) Background Debug Mode背景调试模块
上传时间： 2013-12-20
上传用户：源码3
以典型的9S08 系列为例，当你选择了一个MCU 型号后，在图1-4 右侧会显示出所有针对该型号芯片可用的项目调试场景。其中：Full Chip Simulator”是芯片全功能模拟仿真，即无需任何目标系统的硬件资源，直接在你的PC 机上模拟运行单片机的程序，在模拟运行过程中可以观察调试程序的各项控制和运行流程，分析代码运行的时间，观察各种变量，等等。CW 提供了功能强大的模拟激励功能，可以在模拟运行时模拟一些外部事件的输入，配合程序调试；P&E Multilink/Cyclone Pro”是基于P&E 公司的硬件调试工具实现实时在线硬件调试。实际就是我们经常说的BDM 调试。BDM 调试是基于芯片本身内含的在线调试功能，可实现程序下载，单步／全速运行，可以设若干个断点，可以观察和修改任意寄存器或RAM 内存空间。BDM 几乎是开发飞思卡尔8 位（9S08 和RS08 系列）、16 位（9S12 系列）和32 位（Coldfire V1 系列）单片机的标准调试模式，运用最为广泛；SofTec HCS08”是另外一家SofTec 公司提供的硬件调试工具，国内使用较少；HCS08 Serial Monitor”是基于芯片串口的监控调试开发模式。由于开发效率较低，现在几乎无人使用。
上传时间： 2013-10-10
上传用户：alex wang
