Abstract: A perfect voltage reference produces a stable voltage independent of any external factors. Real-world voltagereferences, of course, are subject to errors caused by many external factors. One causeof these major errors istemperature. Without care, it is easy to operate a voltage reference outside its operating temperature range. Thisapplication note describes how references respond to temperature changes, and how self-heating can cause a voltagereference to operate outside its recommended temperature range. Once understood, this knowledge can then be used toavoid making this design error.
上传时间： 2013-11-08
上传用户：xianglee
The STM32F10xxx microcontroller family embeds up to three advanced 12-bit ADCs (depending on the device) with a conversion time down to 1 μs. A self-calibration feature is provided to enhance ADC accuracy versus environmental condition changes.
上传时间： 2014-12-23
上传用户：eastimage
PCB 被动组件的隐藏特性解析 传统上，EMC一直被视为「黑色魔术（black magic）」。其实，EMC是可以藉由数学公式来理解的。不过，纵使有数学分析方法可以利用，但那些数学方程式对实际的EMC电路设计而言，仍然太过复杂了。幸运的是，在大多数的实务工作中，工程师并不需要完全理解那些复杂的数学公式和存在于EMC规范中的学理依据，只要藉由简单的数学模型，就能够明白要如何达到EMC的要求。本文藉由简单的数学公式和电磁理论，来说明在印刷电路板（PCB）上被动组件（passivecomponent）的隐藏行为和特性，这些都是工程师想让所设计的电子产品通过EMC标准时，事先所必须具备的基本知识。导线和PCB走线导线（wire）、走线（trace）、固定架……等看似不起眼的组件，却经常成为射频能量的最佳发射器（亦即，EMI的来源）。每一种组件都具有电感，这包含硅芯片的焊线（bond wire）、以及电阻、电容、电感的接脚。每根导线或走线都包含有隐藏的寄生电容和电感。这些寄生性组件会影响导线的阻抗大小，而且对频率很敏感。依据LC 的值（决定自共振频率）和PCB走线的长度，在某组件和PCB走线之间，可以产生自共振（self-resonance），因此，形成一根有效率的辐射天线。在低频时，导线大致上只具有电阻的特性。但在高频时，导线就具有电感的特性。因为变成高频后，会造成阻抗大小的变化，进而改变导线或PCB 走线与接地之间的EMC 设计，这时必需使用接地面（ground plane）和接地网格（ground grid）。导线和PCB 走线的最主要差别只在于，导线是圆形的，走线是长方形的。导线或走线的阻抗包含电阻R和感抗XL = 2πfL，在高频时，此阻抗定义为Z = R + j XL j2πfL，没有容抗Xc = 1/2πfC存在。频率高于100 kHz以上时，感抗大于电阻，此时导线或走线不再是低电阻的连接线，而是电感。一般而言，在音频以上工作的导线或走线应该视为电感，不能再看成电阻，而且可以是射频天线。
上传时间： 2013-10-09
上传用户：时代将军
Abstract: We don't expect manufacturers to produce clothes that in one size that fits everyone. In thesame way, one ESD component can't solve all issues—each application has different ESD requirements.Knowing that "one size fits all" cannot apply to power design, the power designer, or the engineering"super hero," must consider all the potential disruptions to a steady flow of power and thenvarious waysto mitigate them. This tutorial describes voltage- and current-limiting devices and risetime reducers tomanage the power. It also points to free and low-cost software tools to help design lowpass filters, checkcapacitor self-resonance, and simulate circuits.
上传时间： 2013-11-18
上传用户：zhouxuepeng1
Avalanche photo diode (APD) receiver modules arewidely used in fi ber optic communication systems. AnAPD module contains the APD and a signal conditioningamplifi er, but is not completely self contained. It stillrequires signifi cant support circuitry including a highvoltage, low noise power supply and a precision currentmonitor to indicate the signal strength. The challenge issqueezing this support circuitry into applications withlimited board space. The LT®3482 addresses this challengeby integrating a monolithic DC/DC step-up converter andan accurate current monitor. The LT3482 can supportup to a 90V APD bias voltage, and the current monitorprovides better than 10% accuracy over four decades ofdynamic range (250nA to 2.5mA).
上传时间： 2014-01-18
上传用户：wenyuoo
The CAT93C46 is a 1 kb Serial EEPROM memory device which isconfigured as either 64 registers of 16 bits (ORG pin at VCC) or 128registers of 8 bits (ORG pin at GND). Each register can be written (orread) serially by using the DI (or DO) pin. The CAT93C46 features aself−timed internal write with auto−clear. On−chip Power−On Resetcircuit protects the internal logic against powering up in the wrongstate.
上传时间： 2013-11-20
上传用户：ynzfm
Bootloader是微处理器上电时运行的第一段代码，它可以通过通信接口实现对微处理器内部应用程序的更新升级，为网络化嵌入式产品的应用程序升级带来极大的便利。由于目前没有统一嵌入式系统的Bootloader。基于NEC 78K0系列单片机自编程原理，设计出一个适用于78K0/Fx2系列单片机的Bootloader，并能够通过单片机串口在线升级应用程序。 Abstract: Bootloader is the first piece of code executed after microprocessor startup. It makes the embedded product’s firmware update conveniently through communication interface. However， no unified bootloader is available for all kinds of microprocessor products. Based on the principle of self-programming NEC 78K0s’ series， a useful Bootloader which is suitable for 78K0/Fx2s’ series MCU is designed，the design can update the application through serial ports.
标签： Bootloader MCU 自编程
上传时间： 2013-10-26
上传用户：fang2010
The CAT28LV64 is a low voltage, low power, CMOS Parallel EEPROM organized as 8K x 8−bits. It requires a simple interface for in−system programming. On−chip address and data latches, self−timed write cycle with auto−clear and VCC power up/down write protection eliminate additional timing and protection hardware. DATA Polling and Toggle status bit signal the start and end of the self−timed write cycle. Additionally, the CAT28LV64 features hardware and software write protection.
上传时间： 2013-11-16
上传用户：浩子GG
The STWD100 watchdog timer circuits are self-contained devices which prevent systemfailures that are caused by certain types of hardware errors (non-responding peripherals,bus contention, etc.) or software errors (bad code jump, code stuck in loop, etc.).The STWD100 watchdog timer has an input, WDI, and an output, WDO (see Figure 2). Theinput is used to clear the internal watchdog timer periodically within the specified timeoutperiod, twd (see Section 3: Watchdog timing). While the system is operating correctly, itperiodically toggles the watchdog input, WDI. If the system fails, the watchdog timer is notreset, a system alert is generated and the watchdog output, WDO, is asserted (seeSection 3: Watchdog timing).The STWD100 circuit also has an enable pin, EN (see Figure 2), which can enable ordisable the watchdog functionality. The EN pin is connected to the internal pull-downresistor. The device is enabled if the EN pin is left floating.
上传时间： 2013-10-22
上传用户：taiyang250072
很多不同的厂家生产各种型号的计算机，它们运行完全不同的操作系统，但TCP.IP协议族允许它们互相进行通信。这一点很让人感到吃惊，因为它的作用已远远超出了起初的设想。T C P / I P起源于6 0年代末美国政府资助的一个分组交换网络研究项目，到9 0年代已发展成为计算机之间最常应用的组网形式。它是一个真正的开放系统，因为协议族的定义及其多种实现可以不用花钱或花很少的钱就可以公开地得到。它成为被称作“全球互联网”或“因特网(Internet)”的基础，该广域网（WA N）已包含超过1 0 0万台遍布世界各地的计算机。本章主要对T C P / I P协议族进行概述，其目的是为本书其余章节提供充分的背景知识。 TCP.IP协议 缩略语 ACK (ACKnowledgment) TCP首部中的确认标志 API (Application Programming Interface) 应用编程接口 ARP (Address Resolution Protocol) 地址解析协议 ARPANET(Defense Advanced Research Project Agency NETwork) (美国)国防部远景研究规划局 AS (Autonomous System) 自治系统 ASCII (American Standard Code for Information Interchange) 美国信息交换标准码 ASN.1 (Abstract Syntax Notation One) 抽象语法记法1 BER (Basic Encoding Rule) 基本编码规则 BGP (Border Gateway Protocol) 边界网关协议 BIND (Berkeley Internet Name Domain) 伯克利I n t e r n e t域名 BOOTP (BOOTstrap Protocol) 引导程序协议 BPF (BSD Packet Filter) BSD 分组过滤器 CIDR (Classless InterDomain Routing) 无类型域间选路 CIX (Commercial Internet Exchange) 商业互联网交换 CLNP (ConnectionLess Network Protocol) 无连接网络协议 CRC (Cyclic Redundancy Check) 循环冗余检验 CSLIP (Compressed SLIP) 压缩的S L I P CSMA (Carrier Sense Multiple Access) 载波侦听多路存取 DCE (Data Circuit-terminating Equipment) 数据电路端接设备 DDN (Defense Data Network) 国防数据网 DF (Don’t Fragment) IP首部中的不分片标志 DHCP (Dynamic Host Configuration Protocol) 动态主机配置协议 DLPI (Data Link Provider Interface) 数据链路提供者接口 DNS (Domain Name System) 域名系统 DSAP (Destination Service Access Point) 目的服务访问点 DSLAM (DSL Access Multiplexer) 数字用户线接入复用器 DSSS (Direct Sequence Spread Spectrum) 直接序列扩频 DTS (Distributed Time Service) 分布式时间服务 DVMRP (Distance Vector Multicast Routing Protocol) 距离向量多播选路协议 EBONE (European IP BackbONE) 欧洲I P主干网 EOL (End of Option List) 选项清单结束 EGP (External Gateway Protocol) 外部网关协议 EIA (Electronic Industries Association) 美国电子工业协会 FCS (Frame Check Sequence) 帧检验序列 FDDI (Fiber Distributed Data Interface) 光纤分布式数据接口 FIFO (First In, First Out) 先进先出 FIN (FINish) TCP首部中的结束标志 FQDN (Full Qualified Domain Name) 完全合格的域名 FTP (File Transfer Protocol) 文件传送协议 HDLC (High-level Data Link Control) 高级数据链路控制 HELLO 选路协议 IAB (Internet Architecture Board) Internet体系结构委员会 IANA (Internet Assigned Numbers Authority) Internet号分配机构 ICMP (Internet Control Message Protocol) Internet控制报文协议 IDRP (InterDomain Routing Protocol) 域间选路协议 IEEE (Institute of Electrical and Electronics Engineering) （美国）电气与电子工程师协会 IEN (Internet Experiment Notes) 互联网试验注释 IESG (Internet Engineering Steering Group) Internet工程指导小组 IETF (Internet Engineering Task Force) Internet工程专门小组 IGMP (Internet Group Management Protocol) Internet组管理协议 IGP (Interior Gateway Protocol) 内部网关协议 IMAP (Internet Message Access Protocol) Internet报文存取协议 IP (Internet Protocol) 网际协议 I RTF (Internet Research Task Force) Internet研究专门小组 IS-IS (Intermediate System to Intermediate System Protocol) 中间系统到中间系统协议 ISN (Initial Sequence Number) 初始序号 ISO (International Organization for Standardization) 国际标准化组织 ISOC (Internet SOCiety) Internet协会 LAN (Local Area Network) 局域网 LBX (Low Bandwidth X) 低带宽X LCP (Link Control Protocol) 链路控制协议 LFN (Long Fat Net) 长肥网络 LIFO (Last In, First Out) 后进先出 LLC (Logical Link Control) 逻辑链路控制 LSRR (Loose Source and Record Route) 宽松的源站及记录路由 MBONE (Multicast Backbone On the InterNEt) Internet上的多播主干网 MIB (Management Information Base) 管理信息库 MILNET (MILitary NETwork) 军用网 MIME (Multipurpose Internet Mail Extensions) 通用I n t e r n e t邮件扩充 MSL (Maximum Segment Lifetime) 报文段最大生存时间 MSS (Maximum Segment Size) 最大报文段长度 M TA (Message Transfer Agent) 报文传送代理 MTU (Maximum Transmission Unit) 最大传输单元 NCP (Network Control Protocol) 网络控制协议 NFS (Network File System) 网络文件系统 NIC (Network Information Center) 网络信息中心 NIT (Network Interface Tap) 网络接口栓（S u n公司的一个程序） NNTP (Network News Transfer Protocol) 网络新闻传送协议 NOAO (National Optical Astronomy Observatories) 国家光学天文台 NOP (No Operation) 无操作 NSFNET (National Science Foundation NETwork) 国家科学基金网络 NSI (NASA Science Internet) （美国）国家宇航局I n t e r n e t NTP (Network Time Protocol) 网络时间协议 NVT (Network Virtual Terminal) 网络虚拟终端 OSF (Open Software Foudation) 开放软件基金 OSI (Open Systems Interconnection) 开放系统互连 OSPF (Open Shortest Path First) 开放最短通路优先 PAWS (Protection Against Wrapped Sequence number) 防止回绕的序号 PDU (Protocol Data Unit) 协议数据单元 POSIX (Portable Operating System Interface) 可移植操作系统接口 PPP (Point-to-Point Protocol) 点对点协议 PSH (PuSH) TCP首部中的急迫标志 RARP (Reverse Address Resolution Protocol) 逆地址解析协议 RFC (Request For Comments) Internet的文档，其中的少部分成为标准文档 RIP (Routing Information Protocol) 路由信息协议 RPC (Remote Procedure Call) 远程过程调用 RR (Resource Record) 资源记录 RST (ReSeT) TCP首部中的复位标志 RTO (Retransmission Time Out) 重传超时 RTT (Round-Trip Time) 往返时间 SACK (Selective ACKnowledgment) 有选择的确认 SLIP (Serial Line Internet Protocol) 串行线路I n t e r n e t协议 SMI (Structure of Management Information) 管理信息结构 SMTP (Simple Mail Transfer Protocol) 简单邮件传送协议 SNMP (Simple Network Management Protocol) 简单网络管理协议 SSAP (Source Service Access Point) 源服务访问点 SSRR (Strict Source and Record Route) 严格的源站及记录路由 SWS (Silly Window Syndrome) 糊涂窗口综合症 SYN (SYNchronous) TCP首部中的同步序号标志 TCP (Transmission Control Protocol) 传输控制协议 TFTP (Trivial File Transfer Protocol) 简单文件传送协议 TLI (Transport Layer Interface) 运输层接口 TTL (Ti m e - To-Live) 生存时间或寿命 TUBA (TCP and UDP with Bigger Addresses) 具有更长地址的T C P和U D P Telnet 远程终端协议 UA (User Agent) 用户代理 UDP (User Datagram Protocol) 用户数据报协议 URG (URGent) TCP首部中的紧急指针标志 UTC (Coordinated Universal Time) 协调的统一时间 UUCP (Unix-to-Unix CoPy) Unix到U n i x的复制 WAN (Wide Area Network) 广域网 WWW (World Wide Web) 万维网 XDR (eXternal Data Representation) 外部数据表示 XID (transaction ID) 事务标识符 XTI (X/Open Transport Layer Interface) X/ O p e n运输层接口
上传时间： 2013-11-13
上传用户：tdyoung
