虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

SHOW

  • 基于码本映射的语音带宽扩展算法研究

    在现代通信系统中,电话语音的频带被限制在300 Hz~4 kHz的范围内,带来了语音可懂度和自然度的降低。为了在不增加额外成本的前提下提高语音的可懂度和自然度,进行了电话语音频带扩展的研究。提出了一种改进的基于码本映射的语音带宽扩展算法:在码本映射的过程中,使用加权系数来得到映射码本。客观测试结果表明,用此算法得到的宽带语音的谱失真度比用一般的码本映射降低至少2%。主观测试结果表明,用此算法得到的宽带语音具有更好的可懂度和自然度。 Abstract:  In modern communication systems, the bandwidth of telephone speech is limited from 300Hz to 4 kHz, which reduces the intelligibility and naturalness of speech. Telephone speech bandwidth extension is researched to get wideband speech and to improve its intelligibility and naturalness, without increasing extra costs. This paper put forward an improved algorithm of speech bandwidth extension based on codebook mapping. In the process of codebook mapping, weighted coefficients were used to get mapping codebook. Objective tests SHOW that spectral distortion of wideband speech obtained by this algorithm reduces at least 2%, comparing to conditional codebook mapping. Subjective tests SHOW that the wideband speech obtained by this algorithm has better intelligibility and naturalness.

    标签: 映射 带宽 扩展 语音

    上传时间: 2014-12-29

    上传用户:15501536189

  • XAPP996-双处理器参考设计套件

    This is the Xilinx Dual Processor Reference Designs suite. The designs illustrate a few differentdual-core architectures based on the MicroBlaze™ and PowerPC™ processors. The designsillustrate various concepts described in the Xilinx White Paper WP262 titled, “DesigningMultiprocessor Systems in Platform Studio”. There are simple software applications includedwith the reference designs that SHOW various forms of interaction between the two processors.

    标签: XAPP 996 双处理器 参考设计

    上传时间: 2013-10-29

    上传用户:旭521

  • ZigBee无线传感网络的路由协议研究

     为满足无线网络技术具有低功耗、节点体积小、网络容量大、网络传输可靠等技术要求,设计了一种以MSP430单片机和CC2420射频收发器组成的无线传感节点。通过分析其节点组成,提出了ZigBee技术中的几种网络拓扑形式,并研究了ZigBee路由算法。针对不同的传输要求形式选用不同的网络拓扑形式可以尽大可能地减少系统成本。同时针对不同网络选用正确的ZigBee路由算法有效地减少了网络能量消耗,提高了系统的可靠性。应用试验表明,采用ZigBee方式通信可以提高传输速率且覆盖范围大,与传统的有线通信方式相比可以节约40%左右的成本。 Abstract:  To improve the proposed technical requirements such as low-ower, small nodes, large capacity and reliable network transmission, wireless sensor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This paper provided network topology of ZigBee technology by analysing the component of the nodes and researched ZigBee routing algorithm. Aiming at different requirements of transmission mode to choose the different network topologies form can most likely reduce the system cost. And aiming at different network to choose the correct ZigBee routing algorithm can effectively reduced the network energy consumption and improved the reliability of the system. Results SHOW that the communication which used ZigBee mode can improve the transmission rate, cover more area and reduce 40% cost compared with traditional wired communications mode.

    标签: ZigBee 无线传感网络 协议研究 路由

    上传时间: 2013-10-09

    上传用户:robter

  • 基于塑料光纤的高压隔离通信接口设计

     通过比较各种隔离数字通信的特点和应用范围,指出塑料光纤在隔离数字通信中的优势。使用已经标准化的TOSLINK接口,有利于节省硬件开发成本和简化设计难度。给出了塑料光纤的硬件驱动电路,说明设计过程中的注意事项,对光收发模块的电压特性和频率特性进行全面试验,并给出SPI口使用塑料光纤隔离通信的典型应用电路图。试验结果表明,该设计可为电力现场、电力电子及仪器仪表的设计提供参考。 Abstract:  y comparing characteristics and applications area of various isolated digital communications, this article indicates advantages of plastic optical fiber in isolated digital communications. Using the standardized TOSLINK interface, it helps to control costs and difficulty in hardware development and design. Then it gives the hardware driver circuit of plastic optical fiber module, explains the noticed details in design process, gives results on the basis of the optical transceiver module voltage characteristics and frequency characteristics tests. Finally,it gives typical application circuit of the SPI communication port by using plastic optical fiber isolation .The results SHOW that this design can be referenced for the power field, power electronics and instrumentation design.

    标签: 塑料光纤 高压隔离 通信 接口设计

    上传时间: 2014-01-10

    上传用户:gundan

  • 快速跳频通信系统同步技术研究

    同步技术是跳频通信系统的关键技术之一,尤其是在快速跳频通信系统中,常规跳频通信通过同步字头携带相关码的方法来实现同步,但对于快跳频来说,由于是一跳或者多跳传输一个调制符号,难以携带相关码。对此引入双跳频图案方法,提出了一种适用于快速跳频通信系统的同步方案。采用短码携带同步信息,克服了快速跳频难以携带相关码的困难。分析了同步性能,仿真结果表明该方案同步时间短、虚警概率低、捕获概率高,同步性能可靠。 Abstract:  Synchronization is one of the key techniques to frequency-hopping communication system, especially in the fast frequency hopping communication system. In conventional frequency hopping communication systems, synchronization can be achieved by synchronization-head which can be used to carry the synchronization information, but for the fast frequency hopping, Because modulation symbol is transmitted by per hop or multi-hop, it is difficult to carry the correlation code. For the limitation of fast frequency hopping in carrying correlation code, a fast frequency-hopping synchronization scheme with two hopping patterns is proposed. The synchronization information is carried by short code, which overcomes the difficulty of correlation code transmission in fast frequency-hopping. The performance of the scheme is analyzed, and simulation results SHOW that the scheme has the advantages of shorter synchronization time, lower probability of false alarm, higher probability of capture and more reliable of synchronization.

    标签: 快速跳频 同步技术 通信系统

    上传时间: 2013-11-23

    上传用户:mpquest

  • 计算FR4上的差分阻抗(PDF)

    Calculation of the Differential Impedance of Tracks on FR4 substrates There is a discrepancy between calculated and measured values of impedance for differential transmission lineson FR4. This is especially noticeable in the case of surface microstrip configurations. The anomaly is SHOWn tobe due to the nature of the substrate material. This needs to be considered as a layered structure of epoxy resinand glass fibre. Calculations, using Boundary Element field methods, SHOW that the distribution of the electricfield within this layered structure determines the apparent dielectric constant and therefore affects theimpedance. Thus FR4 cannot be considered to be uniform dielectric when calculating differential impedance.

    标签: FR4 计算 差分阻抗

    上传时间: 2013-10-18

    上传用户:masochism

  • 基于EKF的异步电机直接转矩控制系统

    为了提高直接转矩控制(DTC)系统定子磁链估计精度,降低电流、电压测量的随机误差,提出了一种基于扩展卡尔曼滤波(EKF)实现异步电机转子位置和速度估计的方法。扩展卡尔曼滤波器是建立在基于旋转坐标系下由定子电流、电压、转子转速和其它电机参量所构成的电机模型上,将定子电流、定子磁链、转速和转子角位置作为状态变量,定子电压为输入变量,定子电流为输出变量,通过对磁链和转速的闭环控制提高定子磁链的估计精度,实现了异步电机的无速度传感器直接转矩控制策略,仿真结果验证了该方法的可行性,提高了直接转矩的控制性能。 Abstract:  In order to improve the Direct Torque Control(DTC) system of stator flux estimation accuracy and reduce the current, voltage measurement of random error, a novel method to estimate the speed and rotor position of asynchronous motor based on extended Kalman filter was introduced. EKF was based on d-p axis motor and other motor parameters (state vector: stator current, stator flux linkage, rotor angular speed and position; input: stator voltage; output: staror current). EKF was designed for stator flux and rotor speed estimation in close-loop control. It can improve the estimated accuracy of stator flux. It is possible to estimate the speed and rotor position and implement asynchronous motor drives without position and speed sensors. The simulation results SHOW it is efficient and improves the control performance.

    标签: EKF 异步电机 直接转矩 控制系统

    上传时间: 2015-01-02

    上传用户:qingdou

  • 基于Multisim 10的矩形波信号发生器仿真与实现

    在Multisim 10软件环境下,设计一种由运算放大器构成的精确可控矩形波信号发生器,结合系统电路原理图重点阐述了各参数指标的实现与测试方法。通过改变RC电路的电容充、放电路径和时间常数实现了占空比和频率的调节,通过多路开关投入不同数值的电容实现了频段的调节,通过电压取样和同相放大电路实现了输出电压幅值的调节并提高了电路的带负载能力,可作为频率和幅值可调的方波信号发生器。Multisim 10仿真分析及应用电路测试结果表明,电路性能指标达到了设计要求。 Abstract:  Based on Multisim 10, this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier, the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor, the width of frequency was adjusted by using different capacitors provided with multiple switch, the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit,the ability of driving loads was raised, the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit SHOW that the performance indicators of the circuit meets the design requirements.

    标签: Multisim 矩形波 信号发生器 仿真

    上传时间: 2014-01-21

    上传用户:shen007yue

  • Displaying a large bitmap file on a dialog box, in its original size, is quite difficult in the VC++

    Displaying a large bitmap file on a dialog box, in its original size, is quite difficult in the VC++ environment. However, it is possible to display a large bitmap to a predefined area of the dialog by using the StretchBlt( ) function.The major disadvantage of this is that the clarity of the image will be lost. Check out this article for displaying large bitmaps into the desired area of your dialog box in its original size with a scrolling technique used to SHOW the entire bitmap. 滚动显示位图 在VC++环境下,在一个对话框中显示一个原始尺寸的大小的位图文件相当是困难的。然而,通过使用 StretchBlt()函数一个给定的区域显示一个大的位图是可能的。主要的缺点是图像将会失真。看了这篇通过卷动技术显示整个位图技术的文章,你将能够以它的原始尺寸在给定对话框的区域内显示一个大位图。 来源: http://www.codeguru.com/bitmap/ScrollBitmap.html

    标签: Displaying difficult original bitmap

    上传时间: 2014-01-05

    上传用户:yiwen213

  • 先进的窗口管理器。可以在你的桌面上实现冻结、解冻、更名、设置总在最上面、设置不总在最上面、闪烁、最大化、最小化、聚焦、隐藏、显示和中断一个可视或不可视窗口的功能。 An advanced window

    先进的窗口管理器。可以在你的桌面上实现冻结、解冻、更名、设置总在最上面、设置不总在最上面、闪烁、最大化、最小化、聚焦、隐藏、显示和中断一个可视或不可视窗口的功能。 An advanced window manager that allows you to freeze, dfreeze, rename, set always on top, set not always on top, flash, maximize, minimize, focus, hide, SHOW or terminate an visible or invisible window on your desktop.

    标签: advanced window 窗口 可视

    上传时间: 2015-03-25

    上传用户:qq21508895