· 摘要： 传统的DSP软件开发都是先设计DSP上的算法并仿真然后将其写成特定DSP的代码(c或是汇编)在目标板上实现.介绍了一种新的高效、集成的DSP软件设计方法.利用MATLAB7.0新提供的Embeded Target for TI C2000 DSP、simulink、Real-Time Workshop和TI的CCS IDE相结合,在MATLAB环境下生成DSP的C代
上传时间： 2013-07-26
上传用户：hebmuljb
·上传一些无刷电机BLDC的资料，还有几篇直接转矩DTC的控制文章，希望对大家能有帮助。 (原文件名: A New Simulation Model of BLDC Motor With Real Back EMF Waveform.pdf) (原文件名: A Sensorless Approach to Control of a Turbodynamic.PDF)
上传时间： 2013-06-09
上传用户：czl10052678
Abstract: A perfect voltage reference produces a stable voltage independent of any external factors. Real-world voltagereferences, of course, are subject to errors caused by many external factors. One causeof these major errors istemperature. Without care, it is easy to operate a voltage reference outside its operating temperature range. Thisapplication note describes how references respond to temperature changes, and how self-heating can cause a voltagereference to operate outside its recommended temperature range. Once understood, this knowledge can then be used toavoid making this design error.
上传时间： 2013-11-08
上传用户：xianglee
Abstract: This application note presents an overview of the operational characteristics of accurate I²C real-time clocks (RTCs),including the DS3231, DS3231M, and DS3232. It focuses on general application guidelines that facilitate use of device resources forpower management, I²C communication circuit configurations, and I²C characteristics relative to device power-up sequences andinitializations. Additional discussions on decoupling are provided to support developing strategies for mitigating power-supply pushingof device frequency.
上传时间： 2013-11-23
上传用户：WMC_geophy
Precision 16-bit analog outputs with softwareconfigurableoutput ranges are often needed in industrialprocess control equipment, analytical and scientificinstruments and automatic test equipment. In the past,designing a universal output module was a daunting taskand the cost and PCB real estate associated with thisfunction were problematic, if not prohibitive.
上传时间： 2014-12-23
上传用户：如果你也听说
基于MDK RTX 的COrtex—M3 多任务应用设计 武汉理工大学 方安平 武永谊 摘要：本文描述了如何在Cortex—M3 上使用MDK RL—RTX 的方法，并给出了一个简单的多任务应用设计。 关键词：MDK RTX，Cortex，嵌入式，ARM， STM32F103VB 1 MDK RL—RTX 和COrtex—M3 概述 MDK 开发套件源自德国Keil 公司，是ARM 公司目前最新推出的针对各种嵌入式处理器 的软件开发工具。MDKRL—IUX 是一个实时操作系统(RTOS)内核，完全集成在MDK 编译器中。广泛应用于ARM7、ARM9 和Cortex-M3 设备中。它可以灵活解决多任务调度、维护和时序安排等问题。基于RL—I 订X 的程序由标准的C 语言编写，由Real—View 编译器进行编译。操作系统依附于C 语言使声明函数更容易，不需要复杂的堆栈和变量结构配置，大大简化了复杂的软件设计，缩短了项目开发周期。
上传时间： 2014-12-23
上传用户：Yue Zhong
Abstract: Large steel buildings, automobiles, mountains, even people survive real atmospheric lightning.
上传时间： 2013-11-11
上传用户：zgu489
此提出了一种基于Matlab／Simulink及实时代码生成工具R哪(Real．Time Workshop)的电力电子与电力传动控制系统软件的设计方法。首先在Simulink下搭建控制系统模型，进行相应仿真完善，验证控制算法，根据目标DSP型号添加相应DSP内核、外设并设置控制参数，然后直接将模型转化为相应DSP的C源代码．在相应的硬件平台支持下即可完成相关实验。
上传时间： 2013-11-04
上传用户：wincoder
Linear Technology offers a variety of devices that simplifyconverting power from a USB cable, but the LTC®3455represents the highest level of functional integration yet. The LTC3455 seamlessly manages power flowbetween an AC adapter, USB cable and Li-ion battery,while complying with USB power standards, all from a4mm × 4mm QFN package. In addtion, two high efficiencysynchronous buck converters generate low voltage railswhich most USB-powered peripherals require. TheLTC3455 also provides power-on reset signals for themicroprocessor, a Hot SwapTM output for poweringmemory cards as well as an uncommitted gain blocksuitable for use as a low-battery comparator or an LDOcontroller. The PCB real estate required for the entire USBpower control circuit and two DC/DC converters is only225mm2.
上传时间： 2013-11-02
上传用户：名爵少年
Multiple-voltage electronics systems often requirecomplex supply voltage tracking or sequencing, whichif not met, can result in system faults or even permanentfailures in the fi eld. The design diffi culties in meetingthese requirements are often compounded in distributedpowerarchitectures where point-of-load (POL) DC/DCconverters or linear regulators are scattered across PCboard space, sometimes on different board planes. Theproblem is that power supply circuitry is often the lastcircuitry to be designed into the board, and it must beshoehorned into whatever little board real estate is left.Often, a simple, drop-in, fl exible solution is needed tomeet these requirements.
上传时间： 2013-10-08
上传用户：15071087253
