This file is distributed in the hope that it will be useful, but WITHOUT WARRANTY OF ANY KIND. Author(s): Ole Saether DESCRIPTION: This example should be used together with ex2a-tx433.asm. One nRF9E5 evaluation board (receiver) should be Programmed with the hex-file generated from assembling this file and the other evaluation board (transmitter) Programmed with the hex-file generated from assembling ex2a-tx433.asm. All switches on the DIP-swith S206 on the receiver must be set to the "on" position and all switches on the DIP-swith S205 on the transmitter must be set to the "on" position. When one of the switched SW1-SW4 on the transmitter is pressed the corresponding LED on the receiver is turned on. The functionality is the same as in ex2c-rx.c.
标签： distributed WARRANTY WITHOUT useful
上传时间： 2017-05-17
上传用户：xieguodong1234
This tutorial explains how to communicate with IO devices on the DE2 Board and how to deal with interrupts using C and the Altera Monitor Program. Two example programs are given that diplay the state of the toggle switches on the red LEDs. The fi rst program uses the Programmed I/O approach and the second program uses interrupts.
标签： with communicate how tutorial
上传时间： 2013-12-13
上传用户：熊少锋
The SL11RIDE is a low cost, high speed Universal Serial Bus RISC based Controller board. It contains a 16-bit RISC processor with built in SL11RIDE ROM to greatly reduce firmware development efforts. Its serial flash EEPROM interface offers low cost storage for USB device configuration and customer product specific functions. New functions can be Programmed into the I2C by downloading it from a USB Host PC. This unique architecture provides the ability to upgrade products, in the field, without changing the peripheral hardware.
标签： Controller Universal contains Serial
上传时间： 2014-01-06
上传用户：15071087253
MTK flash TOOL源程序代码 ========== FlashTool v3.1.05 (2007/05/15) ======= Bug fixes: 1. [DA] Fix that DA cannot be loaded on MT6225 for exceeding internal SRAM size. 2. [DA] Fix that NAND download/read-back issue on MT6225 because buffer is linked on TCM. New features: 1. [DA] Supports new NOR Flash device [SPANSION] S29WS128P [SPANSION] S29WS256P [TOSHIBA] TV00560002DDGB 2. [DA] Supports OTP driver for below NOR Flash device [SPANSION] S29WS128P [SPANSION] S29WS256P Enhancements: 1. [DA] Provide Customized FlashTest_AllInOne_DA.bin. 2. [DA] NFB can auto format after first download. 3. [DA] Improve DA download algorithm: next sector will be erased only when a sector is fully Programmed. 4. [DA] Improve DA download algorithm: enable recovery mechanism when press STOP button. 5. [DA] Improve MT6223 Download Speed.
上传时间： 2014-01-04
上传用户：xg262122
Data logger external EEPROM function based on new Renesus microcontroller. This module has been tested on the renesus develop board.EEPROM was Programmed with temperature calibration beforehand.
标签： microcontroller external function Renesus
上传时间： 2017-09-01
上传用户：yoleeson
Simulation is experimentation with models. For system design, research, and edu- cation, simulations must not only construct and modify many different models but also store and access a large volume of results. That is practical only with models Programmed on computers [1,2]
上传时间： 2020-06-10
上传用户：shancjb
STM32L053C8T6数据手册Features • Ultra-low-power platform – 1.65 V to 3.6 V power supply – -40 to 125 °C temperature range – 0.27 µA Standby mode (2 wakeup pins) – 0.4 µA Stop mode (16 wakeup lines) – 0.8 µA Stop mode + RTC + 8 KB RAM retention – 139 µA/MHz Run mode at 32 MHz – 3.5 µs wakeup time (from RAM) – 5 µs wakeup time (from Flash) • Core: ARM® 32-bit Cortex®-M0+ with MPU – From 32 kHz up to 32 MHz max. – 0.95 DMIPS/MHz • Reset and supply management – Ultra-safe, low-power BOR (brownout reset) with 5 selectable thresholds – Ultralow power POR/PDR – Programmable voltage detector (PVD) • Clock sources – 1 to 25 MHz crystal oscillator – 32 kHz oscillator for RTC with calibration – High speed internal 16 MHz factory-trimmed RC (+/- 1%) – Internal low-power 37 kHz RC – Internal multispeed low-power 65 kHz to 4.2 MHz RC – PLL for CPU clock • Pre-Programmed bootloader – USART, SPI supported • Development support – Serial wire debug supported • Up to 51 fast I/Os (45 I/Os 5V tolerant) • Memories – Up to 64 KB Flash with ECC – 8KB RAM – 2 KB of data EEPROM with ECC – 20-byte backup register
标签： stm32l053c8t6
上传时间： 2022-02-06
上传用户：
The PW4556 series of devices are highly integrated Li-Ion and Li-Pol linear chargers targetedat small capacity battery for portable applications. It is a complete constant-current/ constantvoltage linear charger. No external sense resistor is needed, and no blocking diode is required dueto the internal MOSFET architecture. It can deliver up to 300mA of charge current (using a goodthermal PCB layout) with a final float voltage accuracy of ±1%. The charge voltage is fixed at 4.2V or4.35V, and the charge current can be Programmed externally with a single resistor. The chargerfunction has high accuracy current and voltage regulation loops and charge termination
标签： pw4556
上传时间： 2022-02-11
上传用户：1208020161
The PW4055 is a complete constant-current /constant-voltage linear charger for single cell lithiumion batteries.Its ThinSOT package and low external component count make the PW4055 ideallysuited for portable applications.Furthermore, the PW4055 is specifically designed to work within USBpower specifications.The PW4055 No external sense resistor is needed, and no blocking diode is required due to theinternal MOSFET architecture.Thermal feedback regulates the charge current to limit the dietemperature during high power operation or high ambient temperature. The charge voltage is fixedat 4.2V, and the charge current can be Programmed externally with a single resistor. The PW4055automatically terminates the charge cycle when the charge current drops to 1/10th the Programmedvalue after the final float voltage is reached. When the input supply (wall adapter or USB supply) isremoved, the PW4055 automatically enters a low current state, dropping the battery drain currentto less than 2µA. The PW4055 can be put into shutdown mode, reducing the supply current to 25µA.The BAT pin has a 7KV ESD(HBM) capability. Other features include charge current monitor, undervoltage lockout, automatic recharge and a status pin to indicate charge termination and the presenceof an input voltage
标签： pw4055
上传时间： 2022-02-11
上传用户：jason_vip1
The PW2606B is a front-end over voltage and over current protection device. It achieves wide inputvoltage range from 2.5VDC to 40VDC. The over voltage threshold can be Programmed externally orset to internal default setting. The low resistance of integrated power path nFET switch ensures betterperformance for battery charging system applications. It can deliver up to 1A current to satisfy thebattery supply system. It integrates the over-temperature protection shutdown and auto-recoverycircuit with hysteresis to protect against over current events
标签： pw2606b
上传时间： 2022-02-11
上传用户：
