使用Nios II紧耦合存储器教程 Chapter 1. Using Tightly Coupled Memory with the Nios II Processor Reasons for Using Tightly Coupled Memory . . . . . . . . . . . . . . . . . . . . . . . 1–1 Tradeoffs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1 Guidelines for Using Tightly Coupled Memory . . . .. . . . . . . . 1–2 Hardware Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–2 Software Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . . 1–3 Locating Functions in Tightly Coupled Memory . . . . . . . . . . . . . 1–3 Tightly Coupled Memory Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4 Restrictions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–4 Dual Port Memories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. . . . . . . 1–5 Building a Nios II System with Tightly Coupled Memory . . . . . . . . . . . 1–5
上传时间： 2013-10-13
上传用户：黄婷婷思密达
Nios II 软件开发人员手册中的缓存和紧耦合存储器部分 Nios® II embedded processor cores can contain instruction and data caches. This chapter discusses cache-related issues that you need to consider to guarantee that your program executes correctly on the Nios II processor. Fortunately, most software based on the Nios II hardware abstraction layer (HAL) works correctly without any special accommodations for caches. However, some software must manage the cache directly. For code that needs direct control over the cache, the Nios II architecture provides facilities to perform the following actions:
上传时间： 2013-10-25
上传用户：虫虫虫虫虫虫
Nios II定制指令用户指南：With the Altera Nios II embedded processor, you as the system designer can accelerate time-critical software algorithms by adding custom instructions to the Nios II processor instruction set. Using custom instructions, you can reduce a complex sequence of standard instructions to a single instruction implemented in hardware. You can use this feature for a variety of applications, for example, to optimize software inner loops for digital signal processing (DSP), packet header processing, and computation-intensive applications. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphical user interface (GUI) used to add up to 256 custom instructions to the Nios II processor. The custom instruction logic connects directly to the Nios II arithmetic logic unit (ALU) as shown in Figure 1–1.
上传时间： 2013-10-12
上传用户：kang1923
Nios II 系列处理器配置选项:This chapter describes the Nios® II Processor parameter editor in Qsys and SOPC Builder. The Nios II Processor parameter editor allows you to specify the processor features for a particular Nios II hardware system. This chapter covers the features of the Nios II processor that you can configure with the Nios II Processor parameter editor; it is not a user guide for creating complete Nios II processor systems.
上传时间： 2015-01-01
上传用户：mahone
收文单位：左列各单位 发文字号： MT-8-2-0037
上传时间： 2013-10-28
上传用户：ming529
This application note shows how to achieve low-cost, efficient serial configuration for Spartan FPGA designs. The approachrecommended here takes advantage of unused resources in a design, thereby reducing the cost, part count, memory size,and board space associated with the serial configuration circuitry. As a result, neither processor nor PROM needs to be fullydedicated to performing Spartan configuration.In particular, information is provided on how the idle processing time of an on-board controller can be used to loadconfiguration data from an off-board source. As a result, it is possible to upgrade a Spartan design in the field by sending thebitstream over a network.
上传时间： 2013-11-01
上传用户：wojiaohs
The introduction of Spartan-3™ devices has createdmultiple changes in the evolution of embedded controldesigns and pushed processing capabilities to the “almostfreestage.” With these new FPGAs falling under $20, involume, with over 1 million system gates, and under $5for 100K gate-level units, any design with programmablelogic has a readily available 8- or 16-bit processor costingless than 75 cents and 32-bit processor for less than $1.50.
上传时间： 2013-10-21
上传用户：ligi201200
The Virtex™-4 user access register (USR_ACCESS_VIRTEX4) is a 32-bit register thatprovides direct access to bitstream data by the FPGA fabric. It is useful for loadingPowerPC™ 405 (PPC405) processor caches and/or other data into the FPGA after the FPGAhas been configured, thus achieving partial reconfiguration. The USR_ACCESS_VIRTEX4register is programmed through the bitstream with a command that writes a series of 32-bitwords.
标签： USR_ACCESS PowerPC XAPP 719
上传时间： 2013-12-23
上传用户：yuanwenjiao
The PLB BRAM Interface Controller is a module thatattaches to the PLB (Processor Local Bus).
上传时间： 2013-10-27
上传用户：Breathe0125
The PPC405 Virtex-4 is a wrapper around the Virtex-4PowerPC™ 405 Processor Block primitive. For detailsregarding the PowerPC 405, see the PowerPC 405 ProcessorBlock Reference Guide.
上传时间： 2015-01-02
上传用户：JIUSHICHEN
