开关在电路中起接通信号或断开信号的作用。最常见的可控开关是继电器，当给驱动继电器的驱动电路加高电平或低电平时，继电器就吸合或释放，其触点接通或断开电路。CMOS模拟开关是一种可控开关，它不象继电器那样可以用在大电流、高电压场合，只适于处理幅度不超过其工作电压、电流较小的模拟或数字信号。 一、常用CMOS模拟开关引脚功能和工作原理 1.四双向模拟开关CD4066 CD4066 的引脚功能如图1所示。每个封装内部有4个独立的模拟开关，每个模拟开关有输入、输出、控制三个端子，其中输入端和输出端可互换。当控制端加高电平时，开关导通；当控制端加低电平时开关截止。模拟开关导通时，导通电阻为几十欧姆；模拟开关截止时，呈现很高的阻抗，可以看成为开路。模拟开关可传输数字信号和模拟信号，可传输的模拟信号的上限频率为40MHz。各开关间的串扰很小，典型值为－50dB。
上传时间： 2013-10-27
上传用户：bibirnovis
减小电磁干扰的印刷电路板设计原则 内 容 摘要……1 1 背景…1 1.1 射频源.1 1.2 表面贴装芯片和通孔元器件.1 1.3 静态引脚活动引脚和输入.1 1.4 基本回路……..2 1.4.1 回路和偶极子的对称性3 1.5 差模和共模…..3 2 电路板布局…4 2.1 电源和地…….4 2.1.1 感抗……4 2.1.2 两层板和四层板4 2.1.3 单层板和二层板设计中的微处理器地.4 2.1.4 信号返回地……5 2.1.5 模拟数字和高压…….5 2.1.6 模拟电源引脚和模拟参考电压.5 2.1.7 四层板中电源平面因该怎么做和不应该怎么做…….5 2.2 两层板中的电源分配.6 2.2.1 单点和多点分配.6 2.2.2 星型分配6 2.2.3 格栅化地.7 2.2.4 旁路和铁氧体磁珠……9 2.2.5 使噪声靠近磁珠……..10 2.3 电路板分区…11 2.4 信号线……...12 2.4.1 容性和感性串扰……...12 2.4.2 天线因素和长度规则...12 2.4.3 串联终端传输线…..13 2.4.4 输入阻抗匹配...13 2.5 电缆和接插件……...13 2.5.1 差模和共模噪声……...14 2.5.2 串扰模型……..14 2.5.3 返回线路数目..14 2.5.4 对板外信号I/O的建议14 2.5.5 隔离噪声和静电放电ESD .14 2.6 其他布局问题……...14 2.6.1 汽车和用户应用带键盘和显示器的前端面板印刷电路板...15 2.6.2 易感性布局…...15 3 屏蔽..16 3.1 工作原理…...16 3.2 屏蔽接地…...16 3.3 电缆和屏蔽旁路………………..16 4 总结…………………………………………17 5 参考文献………………………17
上传时间： 2013-10-24
上传用户：18165383642
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
上传时间： 2013-11-10
上传用户：1595690
目录 第一章 传输线理论 一 传输线原理 二 微带传输线 三 微带传输线之不连续分析 第二章 被动组件之电感设计与分析 一 电感原理 二 电感结构与分析 三 电感设计与模拟 电感分析与量测
标签： 传输线
上传时间： 2013-12-12
上传用户：浩子GG
特点(FEATURES) 精确度0.1%满刻度 (Accuracy 0.1%F.S.) 可作各式数学演算式功能如:A+B/A-B/AxB/A/B/A&B(Hi or Lo)/|A| (Math functioA+B/A-B/AxB/A/B/A&B(Hi&Lo)/|A|/etc.....) 16 BIT 类比输出功能(16 bit DAC isolating analog output function) 输入/输出1/输出2绝缘耐压2仟伏特/1分钟(Dielectric strength 2KVac/1min. (input/output1/output2/power)) 宽范围交直流两用电源设计(Wide input range for auxiliary power) 尺寸小,稳定性高(Dimension small and High stability)
上传时间： 2013-11-24
上传用户：541657925
The LTC®3414 offers a compact and efficient voltage regulatorsolution for point of load conversion in electronicsystems that require low output voltages (down to 0.8V)from a 2.5V to 5V power bus. Internal power MOSFETswitches, with only 67mW on-resistance, allow theLTC3414 to deliver up to 4A of output current with efficiencyas high as 94%. The LTC3414 saves space by operatingwith switching frequencies as high as 4MHz, enabling theuse of tiny inductors and capacitors.
上传时间： 2014-01-03
上传用户：dongbaobao
Multiple-voltage electronics systems often requirecomplex supply voltage tracking or sequencing, whichif not met, can result in system faults or even permanentfailures in the fi eld. The design diffi culties in meetingthese requirements are often compounded in distributedpowerarchitectures where point-of-load (POL) DC/DCconverters or linear regulators are scattered across PCboard space, sometimes on different board planes. Theproblem is that power supply circuitry is often the lastcircuitry to be designed into the board, and it must beshoehorned into whatever little board real estate is left.Often, a simple, drop-in, fl exible solution is needed tomeet these requirements.
上传时间： 2013-10-08
上传用户：15071087253
Easy-to-use and compact point-of-load power suppliesare necessary in systems with widely distributed, highcurrent, low voltage loads. The LTC®3415 provides acompact, simple and versatile solution. It includes a pairof integrated complementary power MOSFETs (32mΩtop and 25mΩ bottom) and requires no external senseresistor. A complete design requires an inductor andinput/output capacitors, and that’s it. The result is a fast,constant frequency, 7A current mode DC/DC switchingregulator.
上传时间： 2013-10-18
上传用户：avensy
Advancements in board assembly, PCB layout anddigital IC integration have produced a new generationof densely populated, high performance systems. Theboard-mounted point-of-load (POL) DC/DC power suppliesin these systems are subject to the same demandingsize, high power and performance requirements asother subsystems. The rigorous new POL demands aredifficult to meet with traditional controller or regulatorICs, or power modules.
上传时间： 2014-12-24
上传用户：lbbyxmraon
Many telecommunications and computing applicationsneed high effi ciency step-down DC/DC converters thatcan operate from a very low input voltage. The highoutput power synchronous controller LT3740 is idealfor these applications, converting input supplies rangingfrom 2.2V to 22V to outputs as low as 0.8V with loadcurrents from 2A to 20A. Applications include distributedpower systems, point-of-load regulation and conversionof logic supplies.
上传时间： 2013-11-05
上传用户：zhf01y
