As mentioned, most computers include a serial port. The only hardware setup required is connecting the serial cable to the serial port on the PC and the serial port on the instrument. The serial instrument may include some hardware drivers or software utilities for communication, and should include documentation on the baud rate, packet size, stop bits, and Parity bits that the instrument will use. Additionally, check the National Instruments Instrument Driver Network to see if LabVIEW drivers already exist for yout instrument, as
标签： connecting mentioned computers hardware
上传时间： 2016-05-27
上传用户：gououo
This LDPC software is intended as an introduction to LDPC codes computer based simulation. The pseudo-random irregular low density Parity check matrix is based on Radford M. Neal’s programs collection, which can be found in [1]. While Neal’s collection is well documented, in my opinion, C source codes are still overwhelming, especially if you are not knowledgeable in C language. My software is written for MATLAB, which is more readable than C. You may also want to refer to another MATLAB based LDPC source codes in [2], which has different flavor of code-writing style (in fact Arun has error in his log-likelihood decoder).
标签： LDPC introduction simulation software
上传时间： 2014-12-05
上传用户：change0329
实现8比特字节的RS纠错编码，可以指定极性校验字节数目，能产生的最大校验序列长度为255字节（含极性校验字节）.This is an implementation of a Reed-Solomon code with 8 bit bytes, and a configurable number of Parity bytes. The maximum sequence length (codeword) that can be generated is 255 bytes, including Parity bytes.
上传时间： 2016-08-24
上传用户：思琦琦
This is GPS Matlab findPreambles finds the first preamble occurrence in the bit stream of each channel. The preamble is verified by check of the spacing between preambles [6sec] and Parity checking of the first two words in a subframe. At the same time function returns list of channels, that are in tracking state and with valid preambles in the nav data stream.
标签： findPreambles occurrence the preamble
上传时间： 2013-12-23
上传用户：秦莞尔w
This thesis is devoted to several efficient VLSI architecture design issues in errorcorrecting coding, including finite field arithmetic, (Generalized) Low-Density Parity- Check (LDPC) codes, and Reed-Solomon codes.
标签： errorcorrecting architecture efficient devoted
上传时间： 2017-05-08
上传用户：康郎
matlab中使用LM训练方法计算XOR，3-bit Parity，regression等问题的收敛速度，比较其收敛率。
上传时间： 2014-01-10
上传用户：zhengzg
计数器电路触发器编码器译码器逻辑门数电电路Multisim仿真源文件20个合集:100进制电路测试.ms10100进制电路测试.ms10 (Security copy)74LS161测试电路.ms1074LS161测试电路.ms10 (Security copy)74LS192电路.ms1074LS192电路.ms10 (Security copy)D触发器到T'触发器测试.ms10D触发器到T'触发器测试.ms10 (Security copy)D触发器测试电路.ms10D触发器测试电路.ms10 (Security copy)JK触发器变为T触发器测试.ms10JK触发器变为T触发器测试.ms10 (Security copy)JK触发器测试.ms10JK触发器测试.ms10 (Security copy)RS基本触发器测试.ms10RS基本触发器测试.ms10 (Security copy)任意进制电路设计74LS160.ms10任意进制电路设计74LS160.ms10 (Security copy)四人表决器.ms10四人表决器.ms10 (Security copy)奇偶校验电路(Parity.pdf奇偶校验电路.ms10奇偶校验电路.ms10 (Security copy)抢答器.ms10抢答器.ms10 (Security copy)火灾报警.ms10火灾报警.ms10 (Security copy)简易密码锁设计.ms10简易密码锁设计.ms10 (Security copy)简易测频仪.ms10简易测频仪.ms10 (Security copy)简易秒表电路.ms10简易秒表电路.ms10 (Security copy)编码器74LS148D.ms10编码器74LS148D.ms10 (Security copy)译码器电路.ms10译码器电路.ms10 (Security copy)逻辑门.ms10逻辑门.ms10 (Security copy)
上传时间： 2021-10-27
上传用户：canderile
This example shows how you can use signal functions in the Visiondebugger to simulate a signal that is coming into one of the analog inputs of the LPC21xx.The Measure example is described in detail in the Getting StartedUser's Guide.The MEASURE example program is available for several targets:Simulator: uVision Simulator for LPC2129MCB2100: Keil MCB2100 evaluation board with ULINK debugger - Application is loaded to internal Flash. - Switch S2 (INT1) is used as GPIO and sampled (jumper positions: J1= off, J7= on) - potentiometer POT1 is sampled as AIN0 (jumper position: J2= on) - serial port COM1 parameters: 9600 baud, no Parity, 8-bits, 1 stop bit, flow control noneMCB2130: Keil MCB2130 evaluation board with ULINK debugger - Application is loaded to internal Flash. - Switch S2 (INT1) is used as GPIO and sampled (jumper positions: J1= off, J7= on) - potentiometer POT1 is sampled as AIN1 (jumper position: J2= on) - serial port COM1 parameters: 9600 baud, no Parity, 8-bits, 1 stop bit, flow control none
标签： dac8568
上传时间： 2022-06-28
上传用户：
5GNR信道编码研究，信道编码是 5G 的关键技术之一，描述了 5G 新空口（NR——New Radio Access）的低密度奇偶校验码（LDPCC——Low Density Parity Check Codes）和 极化码（Polar Codes）的关键技术；通过仿真，比较了5G NR的信道编码方案与 4G LTE信道编码方案的性能。另外，还比较了这2代信道编码技术的复杂度和 吞吐量。
标签： 信道编码
上传时间： 2022-06-30
上传用户：
