摘要：从功率MOSFET内部结构和极间电容的电压依赖关系出发，对功率MOSFET的开关现象及其原因进行了较深入分析。从实际应用的角度，对功率MOSFET开关过程的功率损耗和所需驱动功率进行了研究，提出了有关参数的计算方法，并对多种因素对开关特性的影响效果进行了实验研究，所得出的结论对于功率MOSFET的正确运用和设计合理的MoSFET驱动电路具有指导意义．
上传时间： 2013-11-10
上传用户：wfeel
Power conversion by virtue of its basic role produces harmonics due to theslicing of either voltages or currents. To a large extent the pollution in theutility supply and the deterioration of the power quality has been generatedor created by non-linear converters. It is therefore ironic that power convertersshould now be used to clean up the pollution that they helped to create inthe first place.In a utility system, it is desirable to prevent harmonic currents (which resultin EMI and resonance problems) and limit reactive power flows (whichresult in transmission losses).Traditionally, shunt passive filters, comprised of tuned LC elements andcapacitor banks, were used to filter the harmonics and to compensate forreactive current due to non-linear loads. However, in practical applicationsthese methods have many disadvantages.
上传时间： 2013-11-05
上传用户：AISINI005
This reference design (RD) features a fullyassembled and tested surface-mount printed circuitboard (PCB). The RD board utilizes the MAX48851:2 or 2:1 multiplexer and other ICs to implement acomplete video graphics array (VGA) 8:1multiplexer.VGA input/output connections are provided to easilyinterface the MAX4885 RD board with VGAcompatibledevices. The RD board gives the optionto use a single 5V DC power supply (V+), or this RDboard can be powered from any one of the eight VGA sources.
标签： multiplexer reference VGA
上传时间： 2013-11-09
上传用户：ANRAN
OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very highefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very high efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.
上传时间： 2013-10-27
上传用户：落花无痕
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上传时间： 2014-12-23
上传用户：han_zh
EDA （Electronic Design Automation）即“电子设计自动化”，是指以计算机为工作平台，以EDA软件为开发环境，以硬件描述语言为设计语言，以可编程器件PLD为实验载体(包括CPLD、FPGA、EPLD等)，以集成电路芯片为目标器件的电子产品自动化设计过程。“工欲善其事，必先利其器”，因此，EDA工具在电子系统设计中所占的份量越来越高。下面就介绍一些目前较为流行的EDA工具软件。 PLD 及IC设计开发领域的EDA工具，一般至少要包含仿真器（Simulator）、综合器（Synthesizer）和配置器（Place and Routing, P&R）等几个特殊的软件包中的一个或多个，因此这一领域的EDA工具就不包括Protel、PSpice、Ewb等原理图和PCB板设计及电路仿真软件。目前流行的EDA工具软件有两种分类方法：一种是按公司类别进行分类，另一种是按功能进行划分。 若按公司类别分，大体可分两类：一类是EDA 专业软件公司，业内最著名的三家公司是Cadence、Synopsys和Mentor Graphics；另一类是PLD器件厂商为了销售其产品而开发的EDA工具，较著名的公司有Altera、Xilinx、lattice等。前者独立于半导体器件厂商，具有良好的标准化和兼容性，适合于学术研究单位使用，但系统复杂、难于掌握且价格昂贵；后者能针对自己器件的工艺特点作出优化设计，提高资源利用率，降低功耗，改善性能，比较适合产品开发单位使用。 若按功能分，大体可以分为以下三类。 (1) 集成的PLD/FPGA开发环境 由半导体公司提供，基本上可以完成从设计输入（原理图或HDL）→仿真→综合→布线→下载到器件等囊括所有PLD开发流程的所有工作。如Altera公司的MaxplusⅡ、QuartusⅡ，Xilinx公司的ISE，Lattice公司的 ispDesignExpert等。其优势是功能全集成化，可以加快动态调试，缩短开发周期；缺点是在综合和仿真环节与专业的软件相比，都不是非常优秀的。 (2) 综合类 这类软件的功能是对设计输入进行逻辑分析、综合和优化，将硬件描述语句（通常是系统级的行为描述语句）翻译成最基本的与或非门的连接关系（网表），导出给PLD/FPGA厂家的软件进行布局和布线。为了优化结果，在进行较复杂的设计时，基本上都使用这些专业的逻辑综合软件，而不采用厂家提供的集成PLD/FPGA开发工具。如Synplicity公司的Synplify、Synopsys公司的FPGAexpress、FPGA Compiler Ⅱ等。 (3) 仿真类 这类软件的功能是对设计进行模拟仿真，包括布局布线（P&R）前的“功能仿真”（也叫“前仿真”）和P&R后的包含了门延时、线延时等的“时序仿真”（也叫“后仿真”）。复杂一些的设计，一般需要使用这些专业的仿真软件。因为同样的设计输入，专业软件的仿真速度比集成环境的速度快得多。此类软件最著名的要算Model Technology公司的Modelsim，Cadence公司的NC-Verilog/NC-VHDL/NC-SIM等。 以上介绍了一些具代表性的EDA 工具软件。它们在性能上各有所长，有的综合优化能力突出，有的仿真模拟功能强，好在多数工具能相互兼容，具有互操作性。比如Altera公司的 QuartusII集成开发工具，就支持多种第三方的EDA软件，用户可以在QuartusII软件中通过设置直接调用Modelsim和 Synplify进行仿真和综合。 如果设计的硬件系统不是很大，对综合和仿真的要求不是很高，那么可以在一个集成的开发环境中完成整个设计流程。如果要进行复杂系统的设计，则常规的方法是多种EDA工具协调工作，集各家之所长来完成设计流程。
上传时间： 2013-11-19
上传用户：wxqman
印刷电路板（PCB）设计解决方案市场和技术领军企业Mentor Graphics（Mentor Graphics）宣布推出HyperLynx® PI（电源完整性）产品，满足业内高端设计者对于高性能电子产品的需求。HyperLynx PI产品不仅提供简单易学、操作便捷，又精确的分析，让团队成员能够设计可行的电源供应系统；同时缩短设计周期，减少原型生成、重复制造，也相应降低产品成本。随着当今各种高性能/高密度/高脚数集成电路的出现，传输系统的设计越来越需要工程师与布局设计人员的紧密合作，以确保能够透过众多PCB电源与接地结构，为IC提供纯净、充足的电力。配合先前推出的HyperLynx信号完整性（SI）分析和确认产品组件，Mentor Graphics目前为用户提供的高性能电子产品设计堪称业内最全面最具实用性的解决方案。“我们拥有非常高端的用户，受到高性能集成电路多重电压等级和电源要求的驱使，需要在一个单一的PCB中设计30余套电力供应结构。”Mentor Graphics副总裁兼系统设计事业部总经理Henry Potts表示。“上述结构的设计需要快速而准 确的直流压降(DC Power Drop)和电源杂讯(Power Noise)分析。拥有了精确的分析信息，电源与接地层结构和解藕电容数(de-coupling capacitor number)以及位置都可以决定，得以避免过于保守的设计和高昂的产品成本。”
上传时间： 2013-11-18
上传用户：362279997
PCB LAYOUT 術語解釋(TERMS)1. COMPONENT SIDE(零件面、正面)︰大多數零件放置之面。2. SOLDER SIDE(焊錫面、反面)。3. SOLDER MASK(止焊膜面)︰通常指Solder Mask Open 之意。4. TOP PAD︰在零件面上所設計之零件腳PAD，不管是否鑽孔、電鍍。5. BOTTOM PAD：在銲錫面上所設計之零件腳PAD，不管是否鑽孔、電鍍。6. POSITIVE LAYER：單、雙層板之各層線路；多層板之上、下兩層線路及內層走線皆屬之。7. NEGATIVE LAYER：通常指多層板之電源層。8. INNER PAD：多層板之POSITIVE LAYER 內層PAD。9. ANTI-PAD：多層板之NEGATIVE LAYER 上所使用之絕緣範圍，不與零件腳相接。10. THERMAL PAD：多層板內NEGATIVE LAYER 上必須零件腳時所使用之PAD，一般稱為散熱孔或導通孔。11. PAD (銲墊)：除了SMD PAD 外，其他PAD 之TOP PAD、BOTTOM PAD 及INNER PAD 之形狀大小皆應相同。12. Moat : 不同信號的 Power& GND plane 之間的分隔線13. Grid : 佈線時的走線格點2. Test Point : ATE 測試點供工廠ICT 測試治具使用ICT 測試點 LAYOUT 注意事項:PCB 的每條TRACE 都要有一個作為測試用之TEST PAD(測試點)，其原則如下：1. 一般測試點大小均為30-35mil，元件分布較密時，測試點最小可至30mil.測試點與元件PAD 的距離最小為40mil。2. 測試點與測試點間的間距最小為50-75mil，一般使用75mil。密度高時可使用50mil,3. 測試點必須均勻分佈於PCB 上，避免測試時造成板面受力不均。4. 多層板必須透過貫穿孔(VIA)將測試點留於錫爐著錫面上(Solder Side)。5. 測試點必需放至於Bottom Layer6. 輸出test point report(.asc 檔案powerpcb v3.5)供廠商分析可測率7. 測試點設置處:Setuppadsstacks
上传时间： 2013-10-22
上传用户：pei5
Integrated EMI/Thermal Design forSwitching Power SuppliesWei ZhangThesis submitted to the Faculty of theVirginia Polytechnic Institute and State Universityin partial fulfillment of the requirements for the degree of Integrated EMI/Thermal Design forSwitching Power SuppliesWei Zhang(ABSTRACT)This work presents the modeling and analysis of EMI and thermal performancefor switch power supply by using the CAD tools. The methodology and design guidelinesare developed.By using a boost PFC circuit as an example, an equivalent circuit model is builtfor EMI noise prediction and analysis. The parasitic elements of circuit layout andcomponents are extracted analytically or by using CAD tools. Based on the model, circuitlayout and magnetic component design are modified to minimize circuit EMI. EMI filtercan be designed at an early stage without prototype implementation.In the second part, thermal analyses are conducted for the circuit by using thesoftware Flotherm, which includes the mechanism of conduction, convection andradiation. Thermal models are built for the components. Thermal performance of thecircuit and the temperature profile of components are predicted. Improved thermalmanagement and winding arrangement are investigated to reduce temperature.In the third part, several circuit layouts and inductor design examples are checkedfrom both the EMI and thermal point of view. Insightful information is obtained.
上传时间： 2013-11-10
上传用户：1595690
|Introduction Basic Concept Tips to layout Power circuit Type of Power circuit Basic Concept Maximum Current calculation Resistance of Copper ideal power supply & noise Capacitor & Inductor Power consumption Function of power circuit
上传时间： 2014-01-04
上传用户：kao21
