This example uses the AIC23 codec module of the DM642 EVM Board Support * Library to generate a 1KHz sine wave on the audio Outputs for 5 seconds.
标签： the generate Support Library
上传时间： 2014-12-08
上传用户：lingzhichao
The SL74HC573 is identical in pinout to the LS/ALS573. The device inputs are compatible with standard CMOS Outputs with pullup resistors, they are compatible with LS/ALSTTL Outputs. These latches appear transparent to data (i.e., the Outputs change asynchronously) when Latch Enable is high. When Latch Enable goes low, data meeting the setup and hold time becomes latched.
标签： compatible The 573 identical
上传时间： 2016-12-29
上传用户：变形金刚
The SP486 and SP487 are low–power quad differential line drivers meeting RS-485 and RS-422 standards. The SP486 features a common driver enable control the SP487 provides independent driver enable controls for each pair of drivers. Both feature tri–state Outputs and wide common–mode input range. Both are available in 16–pin plastic DIP and SOIC packages.
标签： differential and standard drivers
上传时间： 2014-01-13
上传用户：tianyi223
This project features a complete JPEG Hardware Compressor (standard Baseline DCT, JFIF header) with 2:1:1 subsampling, able to compress at a rate of up to 24 images per second (on XC2V1000-4 @ 40 MHz with resolution 352x288). Image resolution is not limited. It takes an RGB input (row-wise) and Outputs to a memory the compressed JPEG image. Its quality is comparable to software solutions.
标签： Compressor Hardware Baseline features
上传时间： 2017-04-21
上传用户：wyc199288
This program implements a PIC-based fuzzy inference engine for the Fudge fuzzy development system from Motorola. It works by taking the output from Fudge for the 68HC11 processor, and converting it to a MPASM compatible assembler file using the convert batch file. This file can then be incorporated with fuzzy.asm to create a fuzzy inference engine. Tool chain ---------- FUDGE -> Fuzzy Rules -> MC68HC11.ASM -> CONVERT.BAT -> RULES.ASM -> MPASM FUZZY.ASM -> INTEL HEX Fuzzy input registers --------------------- current_ins 1..8 x 8-bit raw inputs Fuzzy inference function ------------------------ FuzzyEngine Fuzzy output registers ---------------------- cog_outs 1..8 x 8-bit raw Outputs
标签： fuzzy development implements PIC-based
上传时间： 2014-01-18
上传用户：caozhizhi
This project features a full-hardware sound compressor using the well known algorithm: IMA ADPCM. The core acts as a slave WISHBONE device. The output is perfectly compatible with any sound player with the IMA ADPCM codec (included by default in every Windows). Includes a testbench that takes an uncompressed PCM 16 bits Mono WAV file and Outputs an IMA ADPCM compressed WAV file. Compression ratio is fixed for IMA-ADPCM, being 4:1. PLEASE NOTICE THAT THIS CORE IS LICENSED UNDER http://creativecommons.org/licenses/by-nc-sa/3.0/ (Creative Commons Attribution-Noncommercial-Share Alike 3.0 Unported). That means you may use it only for NON-COMMERCIAL purposes.
标签： full-hardware compressor algorithm features
上传时间： 2014-01-14
上传用户：Shaikh
-- Hamming Decoder -- This Hamming decoder accepts an 8-bit Hamming code (produced by the encoder above) and performs single error correction and double error detection. -- download from: www.pld.com.cn & www.fpga.com.cn LIBRARY ieee USE ieee.std_logic_1164.ALL ENTITY hamdec IS PORT(hamin : IN BIT_VECTOR(0 TO 7) --d0 d1 d2 d3 p0 p1 p2 p4 dataout : OUT BIT_VECTOR(0 TO 3) --d0 d1 d2 d3 sec, ded, ne : OUT BIT) --diagnostic Outputs END hamdec ARCHITECTURE ver1 OF hamdec IS BEGIN
标签： Hamming produced Decoder decoder
上传时间： 2017-07-15
上传用户：520
RS_latch using vhdl, When using static gates as building blocks, the most fundamental latch is the simple SR latch, where S and R stand for set and reset. It can be constructed from a pair of cross-coupled NOR (Not OR) logic gates. The stored bit is present on the output marked Q. Normally, in storage mode, the S and R inputs are both low, and feedback maintains the Q and Q Outputs in a constant state, with Q the complement of Q. If S (Set) is pulsed high while R is held low, then the Q output is forced high, and stays high when S returns to low similarly, if R (Reset) is pulsed high while S is held low, then the Q output is forced low, and stays low when R returns to low.
标签： using fundamental the RS_latch
上传时间： 2017-07-30
上传用户：努力努力再努力
In 揚erformance of multi-carrier DS CDMA Systems?we apply a multi-carrier signaling technique to a direct-sequence CDMA system, where a data sequence multiplied by a spreading sequence modulates multiple carriers, rather than a single carrier. The receiver provides a correlator for each carrier, and the Outputs of the correlators are combined with a maximal-ratio combiner. This type of signaling has the desirable properties of exhibiting a narrowband interference suppression effect, along with robustness to fading, without requiring the use of either an explicit RAKE structure or an interference suppression filter.
标签： multi-carrier erformance signaling technique
上传时间： 2017-07-31
上传用户：宋桃子
ADIAL Basis Function (RBF) networks were introduced into the neural network literature by Broomhead and Lowe [1], which are motivated by observation on the local response in biologic neurons. Due to their better approximation capabilities, simpler network structures and faster learning algorithms, RBF networks have been widely applied in many science and engineering fields. RBF network is three layers feedback network, where each hidden unit implements a radial activation function and each output unit implements a weighted sum of hidden units’ Outputs.
标签： introduced literature Broomhead Function
上传时间： 2017-08-08
上传用户：lingzhichao
