Agilent 34401A Service Guide.pdfIEC Measurement Category II includes electrical devices connected to mains at an outlet on a branch circuit. Such devices include most small appliances, test equipment, and other devices that plug into a branch outlet or socket. The 34401A may be used to make measurements with the HI and LO inputs connected to mains in such devices, or to the branch outlet itself (up to 300 VAC). However, the 34401A may not be used with its HI and LO inputs connected to mains in permanently installed electrical devices such as the main circuit-breaker panel, sub-panel disconnect boxes, or permanently wired motors. Such devices and circuits are subject to overvoltages that may exceed the protection limits of the 34401A. Note: Voltages above 300 VAC may be measured only in circuits that are isolated from mains. However, transient overvoltages are also present on circuits that are isolated from mains. The Agilent 34401A are designed to safely withstand occasional transient overvoltages up to 2500 Vpk. Do not use this equipment to measure circuits where transient overvoltages could exceed this level. Additional Notices Waste Electrical and Electronic Equipment (WEEE) Directive 2002/96/EC This product complies with the WEEE Directive (2002/96/EC) marking requirement. The affixed product label (see below) indicates that you must not discard this electrical/electronic product in domestic household waste. Product Category: With reference to the equipment types in the WEEE directive Annex 1, this product is classified as a "MONitORING and Control instrumentation" product. Do not dispose in domestic household waste. To return unwanted products, contact your local Agilent office, or see www.agilent.com/environment/product for more information. Agilent 34138A Test Lead Set The Agilent 34401A is compatible with the Agilent 34138A Test Lead Set described below. Test Lead Ratings Test Leads - 1000V, 15A Fine Tip Probe Attachments - 300V, 3A Mini Grabber Attachment - 300V, 3A SMT Grabber Attachments - 300V, 3A Operation The Fine Tip, Mini Grabber, and SMT Grabber attachments plug onto the probe end of the Test Leads. Maintenance If any portion of the Test Lead Set is worn or damaged, do not use. Replace with a new Agilent 3413
标签： agilent
上传时间： 2022-02-20
上传用户：
设计了农业温湿度智能控制系统,该系统采用DHT11温湿度传感器作为温湿度采集模块,单片机选用AT89C52代替并调用Virtual terminal模拟串口通信,LCD1604液晶显示器实时显示温湿度,实现了温湿度的测量、显示,可自动控制加热、降温、加湿、通风,实现温湿度控制以及超限报警处理,并利用Proteus与Keil进行实际电路的仿真。试验表明,该系统实现了可靠的温湿度监控。We described the design of an intelligent control system of agriculture temperature and humidity.The system uses DHT11 temperature and humidity sensor as the temperature and humidity acquisition module.The SCM adopts AT89C52 to replace and call the virtual terminal for simulating serial communication.LCD1604 displays temperature and humidity in real time,which implements the measurement and display of temperature and humidity.The system is able to automatically control heating,cooling,humidification and ventilation,to achieve temperature and humidity control and over-limit alarm processing.The system also uses Proteus and Keil for actual circuit simulation.The experiment shows that the system is capable of reliable temperature and humidity MONitORING.
上传时间： 2022-03-26
上传用户：aben
近年来反季节种植已成火热趋势,温室大棚的普及十分迅速,而温室大棚对自动化、智能化的要求也越来越迫切,本系统将温室大棚的温湿度、二氧化碳浓度各个方面的检测,通风、浇灌、温度、喷洒农药等各个方面的控制进行综合系统研究,实现温室大棚对自动化、智能化的要求。这一系统是基于单片机控制的智能检测,控制系统包含单片机主控模块、感应检测模块、传感模块,显示、控制模块等[1]。从而提高温室大棚的种植效率,减少劳动力,提高利润等。In recent years,counter-season planting has become a hot trend featuring the rapid popularization of greenhouse and urgent requirement for the automation and intellectualization of greenhouse.This paper offers a comprehensive and systematic study of the MONitORING of temperature,humidity and carbon dioxide concentration in the greenhouse and the control of ventilation,irrigation,temperature and pesticide spraying in order to achieve automation and intellectualization in greenhouse.This system is based on the intelligent detection controlled by single chip computer with the control system including the main control module,induction detection module,sensing module,display and control module of single chip computer,which is effective in improving planting efficiency of greenhouse,reducing labor force and increasing profits.
上传时间： 2022-03-27
上传用户：
设计了自动控制系统综合实验案例“基于LabVIEW和单片机的温度控制系统设计”。实验系统硬件部分由单片机、温度传感器、D/A转换模块、调压模块和电烤箱组成,设计了单片机与各个模块之间的接口电路。软件部分采用LabVIEW软件实现控制算法,并设计监控界面实现参数设定、温度数据实时监控等功能。设计了单片机与LabVIEW软件之间的串口通信程序,实现了输入、输出数据的传输。通过综合实验系统设计,使学生得到控制系统设计和实验调试等综合能力的训练。A comprehensive experimental case of the automatic control system is presented,which is the design of the temperature control system based on LabVIEW and SCM.The hardware part of the experimental system is composed of the SCM,temperature sensor,D/A conversion module,voltage regulating module and electric oven.The interface circuit between the SCM and each module is designed.In the software part,LabVIEW software is used to realize the control algorithm,and the MONitORING interface is designed to realize the functions of parameter setting,temperature data real-time MONitORING,etc.The serial communication program between the SCM and LabVIEW software is designed to realize the transmission of input and output data.Through the design of this comprehensive experimental system,students can get the comprehensive ability training for the control system design,experiment debugging,etc.
上传时间： 2022-03-27
上传用户：qdxqdxqdxqdx
锂电池BMS管理技术是移动机器人的关键技术,本文设计了基于bq76PL455、STM32F103的锂电池管理系统,实现了电池组电压、电流、过压、过流等状态监测;系统配置均衡电路,电池充电过程中若出现电池单体电压不平衡现象,会触发均衡电路,进而提高电池的安全性,延长使用寿命。Lithium battery BMS management technology is the key technology of mobile robot.The lithium battery management system based on bq76PL455 and STM32F103 is proposed to realize the MONitORING of battery pack voltage,current,overvoltage and overcurrent.The system is equipped with equalization circuit.When the battery cell voltage imbalance occurs,the equalization circuit is triggered to improve the safety and service life of the battery.
上传时间： 2022-04-02
上传用户：
在全球气候变暖和石油资源短缺的形势下,推动新能源汽车的发展将成为汽车行业一种新的发展方向。在大力发展新能源电动汽车行业的同时还应兼顾电动汽车充电设施的发展,因此对电动汽车充电桩的设计与研究显得十分必要。对电动汽车直流充电桩的硬件系统进行设计,主要的硬件电路包括安全监测电路、总压采集电路、温湿度检测电路、语音电路。软件包括主要流程图和温湿度检测流程图。Under the situation of global warming and shortage of petroleum resources,promoting the development of new energy vehicles will become a new development direction for the automotive industry.While vigorously developing the new energy electric vehicle industry,we should also take into account the development of electric vehicle charging facilities.Therefore,the design and research of electric vehicle charging piles is very necessary.The hardware system of the electric vehicle DC charging pile is designed.The main hardware circuits include safety MONitORING circuit,total voltage collecting circuit,temperature and humidity detecting circuit,voice circuit and CAN communication.The software includes a main flow chart and a temperature and humidity detection flow chart.
标签： 电动汽车
上传时间： 2022-04-03
上传用户：jason_vip1
为适应双向DC/DC功率变换的电流采样需求,一种高精度高边电流采样电路被提出。其基本思想是在功率电路的高边串入采样电阻,借助电流镜原理并引入偏置电流电路,将双向电流均转换为正向电压输出。通过理论分析与仿真结合的方法对电流镜采样原理及4种不同的偏置电流电路方案进行对比,最后通过实验数据验证了高精度高边电流采样电路的有效性。实验数据表明,该采样电路可在-25~75℃的温度工作范围内,针对-10~＋10 A范围内的电流采样实现优于5%的采样精度。Current sensing plays an important role in controlling,MONitORING or protection functions of power systems.To meet the current sensing requirement of bidirectional DC/DC converters,a high-accuracy bidirectional current sensing circuit is proposed.The proposed current sensing circuit inserts a resistor in the path of the current to be sensed,while the current mirror and biased current circuit are introduced.Therefore,the bidirectional current can be expressed by positive voltage.By theoretical analysis and simulation,the sampling theory is analyzed and four biased current circuits are compared.At last,experimental results verified the proposed method.It is demonstrated that the proposed current sensing circuit can achi...
上传时间： 2022-04-22
上传用户：
随着汽车行业的飞速发展，汽车市场的不断升温，与之相关的电子技术也得到时了迅速发展及广泛应用，汽车技术的成熟使得汽车销售及使用不断壮大，现代汽车的行驶速度也随着路况的提高，汽车性能的提高而不断提升。而由于突发性道路交通事故的频繁发生，人们对汽车安全的关注度也日益提高。在汽车的高速行驶过程中，轮胎故障是驾驶人员最为担心和最难预防的，也是突发性交通事故发生的重要原因。据统计，在高速公路上发生的交通事故有70%-80%是由于爆胎引起的，怎样防止爆胎已成为汽车安全的第一大重要课题。权威的研究结果表明，保持标准的轮胎气压和及时发现轮胎故障是防止爆胎的关键，这就使对轮胎充气压力实行监测显得非常重要。本文设计了一种汽车轮胎压力监测系统（Tire Pressure MONitORING System）TPMS及气压调节系统的结合使用，该系统能够对轮胎的参数进行实时监测，当发轮胎压力参数异常时，及时采取报警措施并进行实时的汽压调节，从而避免交通事故的发生。论文在对当前存在的各种TPMS系统结构形式进行分析和比较后，选用一种现行直接式TPMS结合气压调节系统，实现轮胎压力实时的监测和调节的一种新型系统。提出一种基于直接式TPMS系统的，引入调节功能的新型设计。设计本身解决原有直接式TPMS的电池供电影响系统寿命的瓶颈，保证了监测系统的的稳定性。气压调节系统将解决汽车轮胎压力偏差的问题，在监测到气压偏高或者偏低时，对驾驶人员作出警报提醒并实时启动气压调节系统进行胎压调节，在数他钟内调节气压到标准值，保证行驶的畅顺。本文对系统的电源部分，气压调节部分进行了分析设计，解决系统供电，信号采集，信号处理及执行调节，RFLF通信通等关键技术问题。对硬件进行测试。结果表明，该系统切实可行，成本，通信距离及可靠性方面均达到没计指标。
标签： 汽车胎压监测
上传时间： 2022-06-19
上传用户：kingwide
German universities and scientists have repeatedly set the intermational standard in drive technology. Identification and active compensation of natural frequencies in oscillatory mechanics, status controls with MONitORING structures incorporating acceleration sensors, adaptive compensation of measurement system deficiencies, self-adjusting detent torque compensation… everything invented with only a single aim in mind: to continue improv-ing the motion control, dynamics, precision and processing speed of your machines. For the industrial applicabability of this technology scientific publications in proceedings and laboratory test rigs are not enough. These features consequenty need to be converted into cost-efficient and easily manageable products. That 's exactly what we have done.So in future, if you should need more than today ' smarket can offer you, now everything isgoing to be alright. With our new high-performance ServoOne drive series you will experi-ence
标签： servoone
上传时间： 2022-06-24
上传用户：kingwide
MotioninterfaceTM is becoming a "must-have"function being adopted by smartphone and tablet manufacturers due to the enormous value it adds to the end user experience. In smartphones, it finds use in applications such as gesture commands for applications and phone control, enhanced gaming, augmented reality, panoramic photo capture and viewing, and pedestrian and vehicle navigation. With its ability to precisely and accurately track user motions, MotionTracking technology can convert handsets and tablets into powerful 3D intelligent devices that can be used in applications ranging from health and fitness MONitORING to location-based services. Key requirements for Motionlnterface enabled devices are small package size, low power consumption, high accuracy and repeatability, high shock tolerance, and application specific performance programmability-all at a low consumer price point.
标签： mpu6050
上传时间： 2022-07-06
上传用户：zhaiyawei
