制作基于PIC Mcu 的ADS-B接收机的全套资料，包括SCH、PCB、源码和PC端软件。
上传时间： 2013-04-24
上传用户：cx111111
2012TI杯陕西赛题H题,2012TI杯陕西赛题B题--频率补偿电路.
上传时间： 2013-10-07
上传用户：ysystc670
PSHLY-B回路电阻测试仪介绍
上传时间： 2013-11-05
上传用户：木子叶1
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, and 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, and 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, and anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
摘 要:用一种新的思路和方法,先计算低通、再计算高通滤波器的有关参数,然后组合成带通滤波器.关键词:滤波器;参数;新思路中图分类号: TN713. 5 文献识别码:B 文章编号:1008 - 1666 (1999) 04 - 0089 - 03A New Consideration of the Band Filter’s CalculationGuo Wencheng( S hao Yang B usiness and Technology school , S haoyang , Hunan ,422000 )Abstract :This essay deals with a new method of calculating the band filters - first calculatingthe relevant parameters of low - pass filters ,then calculating the ones of high - pass filters.Key words :filter ; parameters ;new considercation八十年代后,信息产业得到了迅猛发展. 带通滤波器在微波通信、广播电视和精密仪器设备中得到了广泛应用. 带通滤波器性能的优劣,对提高接收机信噪比,防止邻近信道干扰,提高设备的技术指标,有着十分重要的意义.我在长期的教学实践中,用切比雪夫型方法设计、计算出宽带滤波器集中参数元件的数据. 该滤波器可运用在检测微波频率的仪器和其他设备中. 再将其思路和计算方法介绍给大家,供参考.
上传时间： 2014-12-28
上传用户：Yukiseop
TKS仿真器B系列快速入门
上传时间： 2013-10-31
上传用户：aix008
一个简单好用的B+树算法实现
上传时间： 2015-01-04
上传用户：缥缈
一个用Basic实现的B-Tree算法
上传时间： 2013-12-30
上传用户：ccclll
一个用Java applet实现的B-Tree算法
上传时间： 2013-12-25
上传用户：qiao8960
用C++实现的B-Tree算法
上传时间： 2014-01-20
上传用户：jiahao131
