The LTC®3207/LTC3207-1 is a 600mA LED/Camera driverwhich illuminates 12 Universal LEDs (ULEDs) and onecamera fl ash LED. The ULEDs are considered universalbecause they may be individually turned on or off, setin general purpose output (GPO) mode, set to blink at aselected on-time and period, or gradate on and off at aselected gradation rate. This device also has an externalenable (ENU) pin that may be used to blink, gradate, orturn on/off the LEDs without using the I2C bus. This may beuseful if the microprocessor is in sleep or standby mode. Ifused properly, these features may save valuable memoryspace, programming time, and reduce the I2C traffi c.
上传时间： 2014-01-04
上传用户：LANCE
Abstract: Designers who must interface 1-Wire temperature sensors with Xilinx field-programmable gate arrays(FPGAs) can use this reference design to drive a DS28EA00 1-Wire slave device. The downloadable softwarementioned in this document can also be used as a starting point to connect other 1-Wire slave devices. The systemimplements a 1-Wire master connected to a UART and outputs temperature to a PC from the DS28EA00 temperaturesensor. In addition, high/low alarm outputs are displayed from the DS28EA00 PIO pins using LEDs.
标签： PicoBlaze Create Master Xilinx
上传时间： 2013-11-12
上传用户：大三三
微电脑型RS-485显示电表（24*48mm/48*96mm） 特点： 5位数RS-485显示电表 显示范围-19999-99999位數 通訊协议Modbus RTU模式 宽范围交直流兩用電源設計 尺寸小,穩定性高 主要规格： 显示范围:-19999~99999 digit RS-485传输速度: 19200/9600/4800/2400 selective RS-485通讯位址: "01"-"FF" RS-485通讯协议: Modbus RTU mode 显示幕: Red high efficiency LEDs high 10.16 mm (0.4") (MMX-RS-11X) Red high efficiency LEDs high 20.32 mm (0.8") (MMX-RS-12X) Red high efficiency LEDs high 10.16 mm (0.4")x2 (MMX-RS-22X) 参数设定方式: Touch switches 记忆方式: Non-volatile E²PROM memory 绝缘耐压能力: 2KVac/1 min. (input/power) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2015-01-03
上传用户：feitian920
微电脑型单相交流集合式电表（单相二线系统） 特点： 精确度0.25%满刻度±1位数 可同时量测与显示交流电压,電流,頻率,瓦特,(功率因數/視在功率) 交流電壓,電流,瓦特皆為真正有效值(TRMS) 交流電流,瓦特之小數點可任意設定 瓦特單位W或KW可任意設定 CT比可任意設定(1至999) 輸入與輸出絕緣耐压 2仟伏特/1分鐘( 突波測試強度4仟伏特(1.2x50us) 數位RS-485界面 (Optional) 主要规格： 精确度: 0.1% F.S.±1 digit (Frequency) 0.25% F.S.±1 digit(ACA,ACV,Watt,VA) 0.25% F.S. ±0.25o(Power Factor) (-.300~+.300) 输入负载: <0.2VA (Voltage) <0.2VA (Current) 最大过载能力: Current related input: 3 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1sec. Voltage related input: maximum 2 x rated continuous 过载显示: "doFL" 显示值范围: 0~600.0V(Voltage) 0~999.9Hz(Frequency)(<20% for voltage input) 0~19999 digit adjustable(Current,Watt,VA) 取样时间: 2 cycles/sec. RS-485通讯位址: "01"-"FF" RS-485传输速度: 19200/9600/4800/2400 selective RS-485通信协议: Modbus RTU mode 温度系数: 100ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 10.16 mm(0.4") 参数设定方式: Touch switches 记忆型式: Non-volatile E²PROM memory 绝缘抗阻: >100Mohm with 500V DC 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600 Vdc (input/output) 突波测试: ANSI c37.90a/1974,DIN-IEC 255-4 impulse voltage 4KV(1.2x50us) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2015-01-03
上传用户：几何公差
集合式直流电能表（小功率的） 特点： 精确度0.05%满刻度±1位数 可同时量测与显示/直流电压/电流/瓦特（千瓦）/瓦特小时（千瓦小时） 电压输入（DC0-99.99V/0-600.0V）自动变档功能 显示范围0-9999(电流/瓦特/千瓦),0至99999999(八位數瓦特小时)可任意规划 数位RS-485 界面 (Optional) 主要规格： 辅助电源消耗功率：＜0.35VA(DC12V/DC24V) ＜0.5VA（DC48V） ＜1.5VA（AC90-240V(50/60Hz)） 精确度: 0.05% F.S. ±1 digit (23 ±5℃) 输入范围：Auto range(DC0-99.99V/0-600.0V(DC voltage)) 输入抗阻：＞5MΩ（DC voltage） 取样时间：10 cycles/second(total) 过载显示: " doFL " 显示值范围: 0-9999 digit（DCA/W(KW)） 0-9999999.999 digit(WH/(KWH)) RS-485传输速度: 19200/9600/4800/2400 selective RS-485通讯位址: "01"-"FF"（0-255） RS-485通信协议: Modbus RTU mode 温度系数: 50ppm/℃ (0-50℃) 显示幕:Bight Red LEDs high 10.16 mm(0.4") 参数设定方式: Touch switches 记忆方式: Non-volatile E²PROM memory 绝缘耐压能力:2KVac/1min.(input/output)（RS-485(Isolating)） 1600 Vdc (input/output) （RS-485(Isolating)） 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-20
上传用户：s363994250
The aim of this application note is to show to scan the 4x4 matrix keypad multiplexed with a four 7-segment display. The software attached to this application note scans the pressed key and displays it on the multiplexed 7- segment LEDs. This application note makes obvious Interrupt capability of the STR710 device to offer a better key scan .
标签： application multiplexed matrix keypad
上传时间： 2015-09-13
上传用户：thuyenvinh
his design is the initial design when the board is powered-up. It increments a counter and displays the value on the 7-segment displays and LEDs. An image is also displayed on the VGA port.
标签： design increments powered-up the
上传时间： 2014-01-17
上传用户：003030
Spartan 3 Digilent Demo:This demo drives the perphrials on the Spartan 3 board. This drives a simple pattern to the VGA port, connects the switches to the LEDs, buttons to each anode of the seven segment decoder. The seven segment decoder has a simple counter running on it, and when SW0 is in the up position the seven segment decoder will display scan codes from the PS2 port. This demo how ever does not drive the RS-232 port or the memory. This is a simple design done entirely VHDL not microblaze.
标签： Spartan drives This perphrials
上传时间： 2014-05-29
上传用户：SimonQQ
VDSP++打开。This directory contains an example ADSP-BF537 RTC project that does a basic blink routine and then puts the part in deep sleep mode to be woken up from a RTC Stopwatch Event. Once woken up, the RTC is reconfigured to toggle the EZ KIT LEDs using RTC second, minute, hour, and day interrupts.
标签： directory contains ADSP-BF example
上传时间： 2015-12-29
上传用户：330402686
Linux 2.4.18 s3c2440 led driver 使用dev-C++撰寫，需要linux 2.4.18 kernel include，編譯完成後產生led module。 insmod main.o //安裝模組 mknod /dev/LEDs c 221 0 使用方法： int main(int argc, char *argv[]) { int testdev //led test... testdev = open("/dev/QuickMarkLed",O_RDWR) ioctl(testdev, 2, 1) //ioctl(device, led number, open/close) open=1 ioctl(testdev, argv[1][0]- 0 , argv[2][0]- 0 ) //ioctl(device, led number, open/close) open=1 close(testdev) return 0 }
标签： s3c2440 driver Linux dev-C
上传时间： 2014-01-01
上传用户：qlpqlq
