虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

HIgh

  • 光电转换电路设计

    OPTOELECTRONICS CIRCUIT COLLECTION AVALANCHE PHOTODIODE BIAS SUPPLY 1Provides an output voltage of 0V to +80V for reverse biasingan avalanche photodiode to control its gain. This circuit canalso be reconfigured to supply a 0V to –80V output.LINEAR TEC DRIVER–1This is a bridge-tied load (BTL) linear amplifier for drivinga thermoelectric cooler (TEC). It operates on a single +5Vsupply and can drive ±2A into a common TEC.LINEAR TEC DRIVER–2This is very similar to DRIVER–1 but its power output stagewas modified to operate from a single +3.3V supply in orderto increase its efficiency. Driving this amplifier from astandard +2.5V referenced signal causes the output transistorsto have unequal power dissipation.LINEAR TEC DRIVER–3This BTL TEC driver power output stage achieves very HIghefficiency by swinging very close to its supply rails, ±2.5V.This driver can also drive ±2A into a common TEC. Operationis shown with the power output stage operating on±1.5V supplies. Under these conditions, this linear amplifiercan achieve very HIgh efficiency. Application ReportThe following collection of analog circuits may be useful in electro-optics applications such as optical networkingsystems. This page summarizes their salient characteristics.

    标签: 光电转换 电路设计

    上传时间: 2013-10-27

    上传用户:落花无痕

  • 射频集成电路设计John Rogers(Radio Freq

    Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses HIgh-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.

    标签: Rogers Radio John Freq

    上传时间: 2014-12-23

    上传用户:han_zh

  • HIgh-speed Digital Design 中文版(高速数字设计)

    介绍高速电路的设计

    标签: HIgh-speed Digital Design 高速数字

    上传时间: 2013-10-16

    上传用户:yt1993410

  • 多层印制板设计基本要领

    【摘要】本文结合作者多年的印制板设计经验,着重印制板的电气性能,从印制板稳定性、可靠性方面,来讨论多层印制板设计的基本要求。【关键词】印制电路板;表面贴装器件;高密度互连;通孔【Key words】Printed Circuit Board;Surface Mounting Device;HIgh Density Interface;Via一.概述印制板(PCB-Printed Circuit Board)也叫印制电路板、印刷电路板。多层印制板,就是指两层以上的印制板,它是由几层绝缘基板上的连接导线和装配焊接电子元件用的焊盘组成,既具有导通各层线路,又具有相互间绝缘的作用。随着SMT(表面安装技术)的不断发展,以及新一代SMD(表面安装器件)的不断推出,如QFP、QFN、CSP、BGA(特别是MBGA),使电子产品更加智能化、小型化,因而推动了PCB工业技术的重大改革和进步。自1991年IBM公司首先成功开发出高密度多层板(SLC)以来,各国各大集团也相继开发出各种各样的高密度互连(HDI)微孔板。这些加工技术的迅猛发展,促使了PCB的设计已逐渐向多层、高密度布线的方向发展。多层印制板以其设计灵活、稳定可靠的电气性能和优越的经济性能,现已广泛应用于电子产品的生产制造中。下面,作者以多年设计印制板的经验,着重印制板的电气性能,结合工艺要求,从印制板稳定性、可靠性方面,来谈谈多层制板设计的基本要领。

    标签: 多层 印制板

    上传时间: 2013-11-19

    上传用户:zczc

  • 高性能覆铜板的发展趋势及对环氧树脂性能的新需求

    讨论、研究高性能覆铜板对它所用的环氧树脂的性能要求,应是立足整个产业链的角度去观察、分析。特别应从HDI多层板发展对高性能CCL有哪些主要性能需求上着手研究。HDI多层板有哪些发展特点,它的发展趋势如何——这都是我们所要研究的高性能CCL发展趋势和重点的基本依据。而HDI多层板的技术发展,又是由它的应用市场——终端电子产品的发展所驱动(见图1)。 图1 在HDI多层板产业链中各类产品对下游产品的性能需求关系图 1.HDI多层板发展特点对高性能覆铜板技术进步的影响1.1 HDI多层板的问世,对传统PCB技术及其基板材料技术是一个严峻挑战20世纪90年代初,出现新一代高密度互连(HIgh Density Interconnection,简称为 HDI)印制电路板——积层法多层板(Build—Up Multiplayer printed board,简称为 BUM)的最早开发成果。它的问世是全世界几十年的印制电路板技术发展历程中的重大事件。积层法多层板即HDI多层板,至今仍是发展HDI的PCB的最好、最普遍的产品形式。在HDI多层板之上,将最新PCB尖端技术体现得淋漓尽致。HDI多层板产品结构具有三大突出的特征:“微孔、细线、薄层化”。其中“微孔”是它的结构特点中核心与灵魂。因此,现又将这类HDI多层板称作为“微孔板”。HDI多层板已经历了十几年的发展历程,但它在技术上仍充满着朝气蓬勃的活力,在市场上仍有着前程广阔的空间。

    标签: 性能 发展趋势 覆铜板 环氧树脂

    上传时间: 2013-11-22

    上传用户:gundan

  • pci e PCB设计规范

    This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good HIgh-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The first section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic HIghlight important constraints, while the narrative that follows offers additional insight.  

    标签: pci PCB 设计规范

    上传时间: 2013-10-15

    上传用户:busterman

  • 确保电解电容器的寿命长-LED灯泡为例

    Abstract: Electrolytic capacitors are notorious for short lifetimes in HIgh-temperature applications such asLED light bulbs. The careful selection of these devices with proper interpretation of their specifications isessential to ensure that they do not compromise the life of the end product. This application notediscusses this problem with electrolytic capacitors in LED light bulbs and provides an analysis that showshow it is possible to use electrolytics in such products.  

    标签: LED 电解电容器 寿命

    上传时间: 2013-11-17

    上传用户:asdfasdfd

  • MR16 LED驱动MR16 LED灯与电子变压器兼容

    Abstract: There are differences between the operation of low-frequency AC transformers and electronic transformersthat supply current to MR16 lamps, and there are also differences in the current draw for MR16 halogen lamps andMR16 LED lamps. These contrasts typically prevent an MR16 LED lamp from operating with most electronictransformers. This article explains how a HIgh-brightness (HB) LED driver optimized for MR16 lamps will allow LEDlamps to be compatible with most electronic transformers.A similar version of this article appeared on Display Plus, July 7, 2012 and in German in Elektronikpraxis, October 1,2012.

    标签: LED MR 16 驱动

    上传时间: 2013-10-14

    上传用户:playboys0

  • MAX16833高电压,高亮度LED驱动器分部设计

    Abstract: This application note details a step-by-step design process for the MAX16833 HIgh-voltageHIgh-brightness LED driver. This process can speed up prototyping and increase the chance for firstpass

    标签: 16833 MAX LED 高电压

    上传时间: 2013-10-09

    上传用户:tianjinfan

  • 高性能DCDC控制器

    We provide complete power solutions with a full lineup of power managementproducts. This brochure provides an overview of our HIgh performance DC/DC switching regulatorcontrollers for applications including datacom, telecom, industrial, automotive, medical, avionicsand control systems. We make power design easier with our industry-leading field applicationengineering support; a broad selection of demonstration boards with schematics, layout filesand parts lists; SwitcherCAD® software for simulation, application notes and comprehensivetechnical documentation.

    标签: DCDC 性能 控制器

    上传时间: 2013-10-15

    上传用户:lz4v4