IEEE 802.11b-1999 Supplement to 802.11-1999,Wireless LAN MAC and PHY specifications: Higher speed Physical Layer (PHY) extension in the 2.4 GHz band
标签： 802.11 1999 specifications Supplement
上传时间： 2016-10-02
上传用户：wlcaption
802.11b-1999/Cor1-2001, IEEE Standard for Information technology—Telecommunications and information exchange between systems—Local and metropolitan area networks—Specific requirements—Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) specifications—Amendment 2: Higher-speed Physical Layer (PHY) extension in the 2.4 GHz band—Corrigendum1
标签： Telecommunications Information information technology
上传时间： 2013-12-10
上传用户：gxf2016
IEEE 802.11g-2003 IEEE Standard for Information technology—Telecommunications and information exchange between systems—Local and metropolitan area networks—Specific requirements—Part 11: Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) specifications—Amendment 4: Further Higher-Speed Physical Layer Extension in the 2.4 GHz Band
标签： Telecommunications IEEE Information information
上传时间： 2016-10-02
上传用户：cx111111
包括EZ811和SL811的文档，应用程序，Windows驱动程序代码，firmware，原理图.更有sl811在linux下作为host的驱动程序源代码及说明文档
上传时间： 2013-12-11
上传用户：banyou
对于那些带有区码限制的DVD光驱，要破解其区码限制，一般有两种方法：一是通过硬手段刷新或修改光驱的Firmware。本代码是firmware的源码。
上传时间： 2013-12-17
上传用户：busterman
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上传时间： 2013-12-13
上传用户：himbly
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising edge. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上传时间： 2014-01-20
上传用户：三人用菜
Cypress公司的FX2系列，USB2.0器件，CY7C68013关于使用Vendor Command 的firmware源码。用Keil uVision2打开。
上传时间： 2016-11-17
上传用户：水中浮云
Can通讯的源码，Defines the special registers and firmware programs for lpc22xx\lpc212x\lpc211x\lpc210x
上传时间： 2016-12-29
上传用户：lifangyuan12
基于VC的USB接口通信程序设计， 本文研发了一套基于USB接口的数据采集系统，整个系统的设计涉及到硬件、设备固件(Firmware)、USB设备驱动程序及客户应用软件。
上传时间： 2017-01-25
上传用户：钓鳌牧马
