To get started with Code Composer Studio™ (CCStudio) Development Tools, review the FIRST two sections of this book. The remaining sections contain more detailed information on specific processes and tools. To determine whether you can utilize these features, see the online help provided with the Code Composer Studio installation.
上传时间： 2013-07-24
上传用户：zaizaibang
Integrating A/D converters have two characteristics incommon. FIRST, as the name implies, their
上传时间： 2013-04-24
上传用户：matlab
·SystemVerilog is a rich set of extensions to the IEEE 1364-2001 Verilog Hardware Description Language (Verilog HDL). These extensions address two major aspects of HDL-based design. FIRST, modeling ver
标签： nbsp SystemVerilog Design for
上传时间： 2013-07-14
上传用户：ainimao
Abstract: For many FIRST-time users, finding the right logger that meets their needs can be a challenging task. In simple
上传时间： 2014-01-19
上传用户：缥缈
The LM20, LM45, LM50, LM60, LM61, and LM62 are analog output temperature sensors. They have various output voltage slopes (6.25mV/°C to 17mV/°C) and power supply voltage ranges (2.4V to 10V).The LM20 is the smallest, lowest power consumption analog output temperature sensor National Semiconductor has released. The LM70 and LM74 are MICROWIRE/SPI compatible digital temperature sensors. The LM70 has a resolution of 0.125°C while the LM74 has a resolution of 0.625°C. The LM74 is the most accurate of the two with an accuracy better than ±1.25°C. The LM75 is National’s FIRST digital output temperature sensor, released several years ago.
上传时间： 2014-12-23
上传用户：yl8908
ANALOG INPUT BANDWIDTH is a measure of the frequencyat which the reconstructed output fundamental drops3 dB below its low frequency value for a full scale input. Thetest is performed with fIN equal to 100 kHz plus integer multiplesof fCLK. The input frequency at which the output is −3dB relative to the low frequency input signal is the full powerbandwidth.APERTURE JITTER is the variation in aperture delay fromsample to sample. Aperture jitter shows up as input noise.APERTURE DELAY See Sampling Delay.BOTTOM OFFSET is the difference between the input voltagethat just causes the output code to transition to the FIRSTcode and the negative reference voltage. Bottom Offset isdefined as EOB = VZT–VRB, where VZT is the FIRST code transitioninput voltage and VRB is the lower reference voltage.Note that this is different from the normal Zero Scale Error.CONVERSION LATENCY See PIPELINE DELAY.CONVERSION TIME is the time required for a completemeasurement by an analog-to-digital converter. Since theConversion Time does not include acquisition time, multiplexerset up time, or other elements of a complete conversioncycle, the conversion time may be less than theThroughput Time.DC COMMON-MODE ERROR is a specification which appliesto ADCs with differential inputs. It is the change in theoutput code that occurs when the analog voltages on the twoinputs are changed by an equal amount. It is usually expressed in LSBs.
上传时间： 2013-11-12
上传用户：pans0ul
Power conversion by virtue of its basic role produces harmonics due to theslicing of either voltages or currents. To a large extent the pollution in theutility supply and the deterioration of the power quality has been generatedor created by non-linear converters. It is therefore ironic that power convertersshould now be used to clean up the pollution that they helped to create inthe FIRST place.In a utility system, it is desirable to prevent harmonic currents (which resultin EMI and resonance problems) and limit reactive power flows (whichresult in transmission losses).Traditionally, shunt passive filters, comprised of tuned LC elements andcapacitor banks, were used to filter the harmonics and to compensate forreactive current due to non-linear loads. However, in practical applicationsthese methods have many disadvantages.
上传时间： 2013-11-05
上传用户：AISINI005
Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated FIRST on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins FIRST with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上传时间： 2014-12-23
上传用户：han_zh
PCB设计问题集锦 问：PCB图中各种字符往往容易叠加在一起，或者相距很近，当板子布得很密时，情况更加严重。当我用Verify Design进行检查时，会产生错误，但这种错误可以忽略。往往这种错误很多，有几百个，将其他更重要的错误淹没了，如何使Verify Design会略掉这种错误，或者在众多的错误中快速找到重要的错误。 答：可以在颜色显示中将文字去掉,不显示后再检查;并记录错误数目。但一定要检查是否真正属于不需要的文字。 问： What’s mean of below warning:(6230,8330 L1) Latium Rule not checked: COMPONENT U26 component rule.答：这是有关制造方面的一个检查，您没有相关设定，所以可以不检查。 问： 怎样导出jop文件？答：应该是JOB文件吧？低版本的powerPCB与PADS使用JOB文件。现在只能输出ASC文件，方法如下STEP：FILE/EXPORT/选择一个asc名称/选择Select ALL/在Format下选择合适的版本/在Unit下选Current比较好/点击OK/完成然后在低版本的powerPCB与PADS产品中Import保存的ASC文件，再保存为JOB文件。 问： 怎样导入reu文件？答：在ECO与Design 工具盒中都可以进行，分别打开ECO与Design 工具盒，点击右边第2个图标就可以。 问： 为什么我在pad stacks中再设一个via:1(如附件）和默认的standardvi(如附件）在布线时V选择1，怎么布线时按add via不能添加进去这是怎么回事，因为有时要使用两种不同的过孔。答：PowerPCB中有多个VIA时需要在Design Rule下根据信号分别设置VIA的使用条件，如电源类只能用Standard VIA等等，这样操作时就比较方便。详细设置方法在PowerPCB软件通中有介绍。 问：为什么我把On-line DRC设置为prevent..移动元时就会弹出(图2),而你们教程中也是这样设置怎么不会呢?答：首先这不是错误,出现的原因是在数据中没有BOARD OUTLINE.您可以设置一个,但是不使用它作为CAM输出数据. 问：我用ctrl+c复制线时怎设置原点进行复制，ctrl+v粘帖时总是以最下面一点和最左边那一点为原点 答： 复制布线时与上面的MOVE MODE设置没有任何关系,需要在右键菜单中选择,这在PowerPCB软件通教程中有专门介绍. 问：用(图4)进行修改线时拉起时怎总是往左边拉起(图5)，不知有什么办法可以轻易想拉起左就左，右就右。答： 具体条件不明,请检查一下您的DESIGN GRID,是否太大了. 问： 好不容易拉起右边但是用(图6)修改线怎么改怎么下面都会有一条不能和在一起，而你教程里都会好好的(图8)答：这可能还是与您的GRID 设置有关,不过没有问题,您可以将不需要的那段线删除.最重要的是需要找到布线的感觉,每个软件都不相同,所以需要多练习。 问： 尊敬的老师:您好！这个图已经画好了，但我只对（如图1）一种的完全间距进行检查，怎么错误就那么多，不知怎么改进。请老师指点。这个图在附件中请老师帮看一下，如果还有什么问题请指出来，本人在改进。谢！！！！！答：请注意您的DRC SETUP窗口下的设置是错误的,现在选中的SAME NET是对相同NET进行检查,应该选择NET TO ALL.而不是SAME NET有关各项参数的含义请仔细阅读第5部教程. 问： U101元件已建好，但元件框的拐角处不知是否正确，请帮忙CHECK 答：元件框等可以通过修改编辑来完成。问： U102和U103元件没建完全，在自动建元件参数中有几个不明白：如：SOIC--》silk screen栏下spacing from pin与outdent from FIRST pin对应U102和U103元件应写什么数值，还有这两个元件SILK怎么自动设置，以及SILK内有个圆圈怎么才能画得与该元件参数一致。 答：Spacing from pin指从PIN到SILK的Y方向的距离,outdent from FIRST pin是第一PIN与SILK端点间的距离.请根据元件资料自己计算。
上传时间： 2013-10-07
上传用户：comer1123
This document provides practical, common guidelines for incorporating PCI Express interconnect layouts onto Printed Circuit Boards (PCB) ranging from 4-layer desktop baseboard designs to 10- layer or more server baseboard designs. Guidelines and constraints in this document are intended for use on both baseboard and add-in card PCB designs. This includes interconnects between PCI Express devices located on the same baseboard (chip-to-chip routing) and interconnects between a PCI Express device located “down” on the baseboard and a device located “up” on an add-in card attached through a connector. This document is intended to cover all major components of the physical interconnect including design guidelines for the PCB traces, vias and AC coupling capacitors, as well as add-in card edge-finger and connector considerations. The intent of the guidelines and examples is to help ensure that good high-speed signal design practices are used and that the timing/jitter and loss/attenuation budgets can also be met from end-to-end across the PCI Express interconnect. However, while general physical guidelines and suggestions are given, they may not necessarily guarantee adequate performance of the interconnect for all layouts and implementations. Therefore, designers should consider modeling and simulation of the interconnect in order to ensure compliance to all applicable specifications. The document is composed of two main sections. The FIRST section provides an overview of general topology and interconnect guidelines. The second section concentrates on physical layout constraints where bulleted items at the beginning of a topic highlight important constraints, while the narrative that follows offers additional insight.
上传时间： 2013-10-15
上传用户：busterman
