锁定放大是微弱信号检测的重要手段。基于相关检测理论，利用开关电容的开关实现锁定放大器中乘法器的功能，提出开关电容和积分器相结合以实现相关检测的方法，并设计出一种锁定放大器。该锁定放大器将微弱信号转化为与之相关的方波，通过后续电路得到正比于被测信号的直流电平，为后续采集处理提供方便。测量数据表明锁定放大器前级可将10-6 A的电流转换为10-1 V的电压，后级通过带通滤波器级联可将信号放大1×105倍。该方法在降低噪声的同时，可对微弱信号进行放大，线性度较高、稳定性较好。 Abstract: Lock-in Amplifying（LIA）is one of important means for weak signal detection. Based on cross-correlation detection theory， switch in the swithched capacitor was used as multiplier of LIA， and a new method of correlation detection was proposed combining swithched capacitor with integrator. A kind of LIA was designed which can convert the weak signal to square-wave， then DC proportional to measured signal was obtained through follow-up conditioning circuit， providing convenience for signal acquisition and processing. The measured data shows that the electric current（10-6 A） can be changed into voltage（10-1 V） by LIA， and the signal is magnified 1×105 times by cascade band-pass filter. The noise is suppressed and the weak signal is amplified. It has the advantages of good linearity and stability.
上传时间： 2013-11-29
上传用户：黑漆漆
Nuvoton NuMicro ICP Programmer 用户指南
标签： Programmer Nuvoton NuMicro ICP
上传时间： 2013-10-27
上传用户：longlong12345678
四位数码管从一数到F,LED就向下移一位c语言代码
上传时间： 2014-12-25
上传用户：1214209695
利用单片机具有的智能程序控制的特点，设计了基于STC89C52单片机的"二极管特性测试器"，可对二极管一般特性进行快速测试。通过稳定线性电流源给二极管加载恒定电流，然后由高精度模数转换器测试其压降，以此为基础可判断二极管好坏、检测二极管极性和测试二极管伏安特性等，避免了用万用表测试只能测得极性而不知其特性这一缺点。可用于电子设计制作过程中对二极管进行快速测试，以确定被测二极管是否满足电路的设计要求。 Abstract: By making good use of the intelligent control function of the Micro Controller Unit (MCU)， the diode trait tester was designed based on the STC89C52，which could be used to test the trait of a diode rapidly. By loading constant current to diode through the stable linear current source， and measuring the voltage drop of the diode by high-precision analogue-to-digital converter (ADC)， it can judge whether the diode is good or not， distinguish the polarity of the diode， and test the trait that the diode， which can avoid the fault of using a multimeter can only measure the polarity but not the trait. This device can be used to test the trait of a diode quickly，and to make sure that whether a diode can be used in the electronic design or not.
上传时间： 2013-11-13
上传用户：assef
Digitemp Junior – An RS-232 Port-Powered Digital Thermometer Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it rel- atively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power sup- plies or batteries. It is powered directly by the RS-232 port.
上传时间： 2013-10-21
上传用户：baitouyu
为解决电致变色器件的颜色变化受外界环境颜色控制的问题，设计了一种基于单片机的便携式颜色自适应识别电路。与传统颜色识别电路相比较，该电路利用数字式的颜色传感器来获取外界环境颜色，产生的数字颜色信号易于单片机进行处理。在电路中，下位机部分主要负责获取电致变色器件变色参数及控制电致变色器件的颜色变化;而上位机部分主要负责把下位机获取的电致变色器件变色参数进行电压到颜色的曲线拟合，并通过蓝牙通信把拟合曲线参数传递给下位机。结果表明，该电路能自动根据环境颜色提供-4~4 V范围步进为0.1 V的电压来驱动电致变色器件的颜色显示，与传统的颜色识别电路设计相比，识别的精度和速度都得到了明显改善。 Abstract: In this paper， a portable adaptive circuit for color identification(PACCI) based on MCU was designed. Compared to the traditional color identification circuit， the PACCI adopts digital sensor to detect the color data from external environment and further generate digital color data， which can be processed easily by MCU. In PACCI， the slave is mainly responsible for detecting the color parameters of the corresponding elcreochromic device and further driving it. For the master， which is mainly responsible for the color curve fitting based on the parameters of the electrochromic device， and transmits the fitting parameters to the slave through the bluetooth device. The results show that the PACCI can provide the basis voltage range from -4V to 4V automatically based on the colors of external environment with step as 0.1V to drive the corresponding electrochromic device. Compared to the traditional color recognition circuit， the recognition accuracy and speed of PACCI have been improved significantly.
上传时间： 2013-11-09
上传用户：franktu
设计了一种基于PIC16C71单片机的数字水温配制阀。该配制阀采用NTC热敏电阻作温度传感器，与固定电阻组成简单分压电路作为水温测量电路，利用PIC16C71单片机内置的8位A/D转换器把热敏电阻上的模拟电压转换为数字量，PIC16C71单片机控制直流电机驱动混水阀调节冷热水的混合比例实现水温调节。给出了控制电路图，对水温测量电路的参数选择和测温精度作了详细讨论。实验和分析表明，选用阻值较大的NTC热敏电阻和分压电阻可较好地解决热敏电阻因功耗较大造成的热击穿问题。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上传时间： 2013-11-08
上传用户：Yue Zhong
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
为了有效地提升铅酸蓄电池的使用寿命，同时实现对充电过程的监控，设计出一种用单片机控制的36 V铅酸蓄电池充电电源。本电路采用反激式拓扑，连续电流工作模式，电源管理IC设计在电源的副边，由ELAN公司的EM78P258N单片机模拟，是用可编程器件模拟电源管理IC，实现智能电源低成本化的一次成功尝试，通过对单片机的软件设计实现了充电电源的状态显示、充电时间控制、报警、过温保护、过压保护、过流保护等功能。本充电器真正的实现了铅酸蓄电池的三段式充电过程，其最高输出功率可达90 W，效率约85%，成本不到20元，具有很高的市场竞争力。 Abstract: In order to extend the life of lead-acid battery efficiently and supervise the charging process meanwhile， a 36V lead-acid battery charge powe supply controlled by microcontroller is designed. The charger is flyback switching power supply and works in CCM mode. A EM78P258N microcontroller made by ELAN microelectronics corporation is used as power management IC which is designed at the secondary circuit. The project is a successful attempt to low-cost intelligent power used microcontroller simulating power management IC. The charger also has the functions of the status reveal， charge time control， alarming， thermal protect， current limit and overvoltage protect by the software design. The circuit actually implements the three-step charge process， whose power is up to 90W and whose efficiency can get 85%. The net cost of this charger is less than 20 RMB， so that the charger is of powerful market competitiveness.
上传时间： 2013-11-16
上传用户：cepsypeng
Digitemp Jr. is a device that is designed to measure and report ambient temperature. When connected to an RS-232 port on any PC, it will periodically measure and report in ASCII form the ambient temperature in degrees Celsius. These temperature readings can be monitored with any terminal program. If the terminal program supports capture to disk, the temperature readings can be saved to disk for further analysis with a spreadsheet program or other data analysis tool. The simple ASCII output format of Digitemp Jr. makes it relatively easy to write custom software for receiving, recording, and analyzing ambient temperature data. Best of all, Digitemp Jr. requires no external power supplies or batteries. It is powered directly by the RS-232 port.
上传时间： 2013-10-20
上传用户：Maple
