The PCA9544A provides 4 interrupt inputs, one for each channeland one open drain interrupt output. When an interrupt is generated byany device, it will be detected by the PCA9544A and the interruptoutput will be driven LOW. The channel need not be active fordetection of the interrupt. A bit is also set in the control byte.Bits 4 – 7 of the control byte correspond to channels 0 – 3 of thePCA9544A, respectively. Therefore, if an interrupt is generated byany device connected to channel 2, the state of the interrupt inputs isloaded into the control register when a read is accomplished.Likewise, an interrupt on any device connected to channel 0 wouldcause bit 4 of the control register to be set on the read. The mastercan then address the PCA9544A and read the contents of thecontrol byte to determine which channel contains the devicegenerating the interrupt. The master can then reconfigure thePCA9544A to select this channel, and locate the device generatingthe interrupt and clear it. The interrupt clears when the deviceoriginating the interrupt clears.
标签： 4channel multiple 9544A 9544
上传时间： 2014-12-28
上传用户：潜水的三贡
The TJA1042 is a high-speed CAN transceiver that provides an interface between aController Area Network (CAN) protocol controller and the physical two-wire CAN bus.The transceiver is designed for high-speed (up to 1 Mbit/s) CAN applications in theautomotive industry, providing the differential transmit and receive capability to (amicrocontroller with) a CAN protocol controller.
标签： High-speed transce 1042 TJA
上传时间： 2014-12-28
上传用户：气温达上千万的
The TJA1051 is a high-speed CAN transceiver that provides an interface between aController Area Network (CAN) protocol controller and the physical two-wire CAN bus.The transceiver is designed for high-speed (up to 1 Mbit/s) CAN applications in theautomotive industry, providing differential transmit and receive capability to (amicrocontroller with) a CAN protocol controller.
标签： High-speed transce 1051 TJA
上传时间： 2013-10-17
上传用户：jisujeke
Luminary Micro provides an analog-to-digital converter (ADC) module on some members of theStellaris microcontroller family. The hardware resolution of the ADC is 10 bits; however, due to noiseand other accuracy-diminishing factors, the true accuracy is less than 10 bits. This application noteprovides a software-based oversampling technique, resulting in an improved Effective Number OfBits (ENOB) in the conversion result. This document describes methods of oversampling an inputsignal, and the impact on precision and overall system performance.
标签： Oversampling Techniques ADC fo
上传时间： 2013-12-17
上传用户：zhyiroy
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上传时间： 2013-10-11
上传用户：dianxin61
基于PIC单片机的脉冲电源:设计了一种金属凝固过程用脉冲电源。该电源采用PIC16F877作为主控芯片，实现对窄脉冲电流幅值的检测，以及时电流脉冲幅值根据模糊PID算法进行闲环控制。使用结果表明：该电源的输出脉冲波形良好，电流幅值稳定，满足合金材料凝固过程的工艺要求且运行稳定可靠。关键词：脉冲电源；PIC16F877单片机；模糊PID；闲环控制 Abstract：A kind of pulse power supply was designed which uses in the metal solidification process ．．I11is power supply used PIC16F877 to take the master control chip reali on to the narrow pulse electric current peak-to-peak value examination，carried on the closed-loop control to the electric current pulse peak-to-peak value basis fuzzy PID algorithm．The use result indicated ，this power supply output se profile is good，and the electric current peak-to-p~k value is stable，It satisfies the alloy material solidification process the technological requirement and movement stable reliable，Key words：p se po wer supply；PIC16F877single-chip microcontroller；f r PID；closed-loop control
上传时间： 2013-10-27
上传用户：xcy122677
本文依据集成电路设计方法学，探讨了一种基于标准Intel 8086 微处理器的单芯片计算机平台的架构。研究了其与SDRAM，8255 并行接口等外围IP 的集成，并在对AMBA协议和8086 CPU分析的基础上，采用遵从AMBA传输协议的系统总线代替传统的8086 CPU三总线结构，搭建了基于8086 IP 软核的单芯片计算机系统，并实现了FPGA 功能演示。关键词：微处理器； SoC；单芯片计算机；AMBA 协议 Design of 8086 CPU Based Computer-on-a-chip System（School of Electrical Engineering and Automation, Heifei University of Technology, Hefei, 230009,China）Abstract: According to the IC design methodology, this paper discusses the design of one kind of Computer-on-a-chip system architecture, which is based on the standard Intel8086 microprocessor,investigates how to integrate the 8086 CPU and peripheral IP such as, SDRAM controller, 8255 PPI etc. Based on the analysis of the standard Intel8086 microprocessor and AMBA Specification,the Computer-on-a-chip system based on 8086 CPU which uses AMBA bus instead of traditional three-bus structure of 8086 CPU is constructed, and the FPGA hardware emulation is fulfilled.Key words: Microprocessor; SoC; Computer-on-a-chip; AMBA Specification
上传时间： 2013-12-27
上传用户：kernor
基于LabVIEW和单片机的空调温度场测量系统的研究:室内温度是空调系统舒适性的重要指标,对其及时、准确地测量显得非常重要。介绍单片机AT89C51 和数字式、单总线型温度传感器DS18B20 组成矩形测量网络采集空调室内40 点温度,LabVIEW作为开发平台,二者之间通过串口实现数据通信,利用LabVIEW强大的数据处理和显示功能对采集的空调温度场数据进行实时处理、分析和显示,详细介绍了系统的硬件结构和软件模块的设计方案。关键词:单片机;DS18B20 ;LabVIEW;串行通信 Abstract : Temperature is a very important criterion of air condition system′s comfort , so it is very significant to measure it accurately and real timely. This paper int roduces a data acquisition system of measuring 40 point s temperature for air condition room based on single wire digital sensor DS18B20 and microcont roller AT89C51 which are composed of rectangle measuring meshwork. The data communication between LabVIEW and microcont roller is executed via serial port ,and the temperature field data of air condition room are processed analyzed and displayed on LabVIEW. The hardware and software modules are also given in detail.Keywords : single chip ;DS18B20 ;LabVIEW; serial communication
上传时间： 2014-05-05
上传用户：KSLYZ
基于单片机的步进电机开环控制系统:通过ATMEL89C51单片机对步进电机进行控制,主要介绍了步进电机控制器、驱动电路和LED显示电路的设计,实现了步进电机的开环控制。在步进电机控制器的设计中,重点阐述了脉冲产生电路以及对速度的控制。该系统具有成本低、控制方便的特点。关键词: 单片机; 步进电机; 开环控制 Abstract: The design using ATMEL89C51 single chip to control the step2motor with its controller, driving circuit and LED disp lay circuit to realize step motor open2loop controlwere introduced. For the controller in this design,the circuit to p roduce pulse and the speed controlwere expatiated emphatically. This system possesses features of lower cost, easier control.Key words: single ch ip; step2motor; open2loop con trol
上传时间： 2013-10-13
上传用户：cicizoe
The C500 microcontroller family usually provides only one on-chip synchronous serialchannel (SSC). If a second SSC is required, an emulation of the missing interface mayhelp to avoid an external hardware solution with additional electronic components.The solution presented in this paper and in the attached source files emulates the mostimportant SSC functions by using optimized SW routines with a performance up to 25KBaud in Slave Mode with half duplex transmission and an overhead less than 60% atSAB C513 with 12 MHz. Due to the implementation in C this performance is not the limitof the chip. A pure implementation in assembler will result in a strong reduction of theCPU load and therefore increase the maximum speed of the interface. In addition,microcontrollers like the SAB C505 will speed up the interface by a factor of two becauseof an optimized architecture compared with the SAB C513.Moreover, this solution lays stress on using as few on-chip hardware resources aspossible. A more excessive consumption of those resources will result in a highermaximum speed of the emulated interface.Due to the restricted performance of an 8 bit microcontroller a pin compatible solution isprovided only; the internal register based programming interface is replaced by a set ofsubroutine calls.The attached source files also contain a test shell, which demonstrates how to exchangeinformation between an on-chip HW-SSC and the emulated SW-SSC via 5 external wiresin different operation modes. It is based on the SAB C513 (Siemens 8 bit microcontroller).A table with load measurements is presented to give an indication for the fraction of CPUperformance required by software for emulating the SSC.
标签： synchronous Emulating serial
上传时间： 2014-01-31
上传用户：z1191176801
