Permission to make digital or hard copies of all or part of this work forpersonal or classroom use is granted without fee provided that copies arenot made or distributed for profit or commercial advantage and that copiesbear this notice and the full citation on the first page. To copy otherwise, torepublish, to post on servers or to redistribute to lists, requires prior specificpermission.
标签： 数字电源
上传时间： 2013-10-16
上传用户：dddddd
ØCPV is the abbreviation of concentration PV. Ø It utilizes optics to concentrate the sunlight to the CPV cell to generate power. Ø The purpose of CPV is to reduce the cell’s area and the cost of PV module.
上传时间： 2013-10-29
上传用户：开怀常笑
Abstract: This application note describes how to build, debug, and run applications on the on-board MAXQ622microcontroller to interface with the DS8005 dual smart card interface. This is demonstrated in both IAREmbedded Workbench and the Rowley CrossWorks IDE, using sample code provided with the kit.
上传时间： 2013-10-29
上传用户：ddddddd
#include<iom16v.h> #include<macros.h> #define uint unsigned int #define uchar unsigned char uint a,b,c,d=0; void delay(c) { for for(a=0;a<c;a++) for(b=0;b<12;b++); }; uchar tab[]={ 0xc0,0xf9,0xa4,0xb0,0x99,0x92,0x82,0xf8,0x80,0x90,
上传时间： 2013-10-21
上传用户：13788529953
设计了一种基于PIC16C71单片机的数字水温配制阀。该配制阀采用NTC热敏电阻作温度传感器，与固定电阻组成简单分压电路作为水温测量电路，利用PIC16C71单片机内置的8位A/D转换器把热敏电阻上的模拟电压转换为数字量，PIC16C71单片机控制直流电机驱动混水阀调节冷热水的混合比例实现水温调节。给出了控制电路图，对水温测量电路的参数选择和测温精度作了详细讨论。实验和分析表明，选用阻值较大的NTC热敏电阻和分压电阻可较好地解决热敏电阻因功耗较大造成的热击穿问题。 Abstract: A digital valve for controlling water temperature based on PIC16C71 was presented in this paper.A bleeder circuit which consisted of a NTC thermistor as temperature sensor and a fixed resistance was designed as water temperature measuring circuit.The analog voltage on the thermistor was converted into digital signal by a 8-bit A/D converter embedded in PIC16C71. Based on the digital signal， the MCU PIC16C71 drived the valve by a DC motor to adjust the water temperature through adjusting the proportion of hot water and cold water.The circuit diagram of controller was given，the principle，the component parameters and the accuracy of measuring temperatures were also dissertated in detail. It was found by experiment and analysis that thermal breakdown of thermistor caused by high power could be solved by selecting thermistor and fixed resistance with high impedance value.
上传时间： 2013-11-08
上传用户：Yue Zhong
在航电系统维护过程中，为解决定位故障的效率和降低维修成本等问题，提出了基于ICD（Interface Control Document，接口控制文件）的1553B总线的信息监控系统模型。该系统运用数据采集卡对总线中传输的信号有无失真、偏差等电气特性进行检测，并使用1553B通讯卡通过测控软件LabWindows/CVI编程与ICD数据库的动态链接，实现总线信息的解析和故障的判断。与传统的维护过程相比，这种模型能够从信号的电气特性以及信息的解析等全方位的去检测判断故障的来源，并且能够广泛在其他1553B总线系统内扩展应用。验证表明该监控系统可以对总线信息进行快速有效地监测分析，能满足应用需求。 Abstract: In the process of avionics system maintenance， to solve the problems such as improving the efficiency of fast orientation to troubles and reducing maintenance cost， system of 1553B bus information monitor model based on ICD was proposed. The system observed whether the data which transmitted on the bus appear distortion and deviation by using data acquisition card. And using 1553B communication card programming of the measure software LabWindows/CVI and the dynamic linking of ICD database， message analysis and fault estimation could be realized. Compared with traditional maintenance， this model can all-dimensionally detect and analyze the source of faults from both electrical characteristics of the signal and message analysis， and it can be widely applied in the other 1553B system. Experiment shown that this monitor system can effectively detect and analyze the bus message and can meet the application requirements.
上传时间： 2013-11-23
上传用户：18752787361
为解决当前计算机串行通讯接口只有USB，难以满足旧型号设备或某些单片机要求RS232通讯的问题，设计出两款RS232/USB电路。采用CH341A与MAX223集成电路芯片构建标准9线RS232/USB通用接口转换器，无需编程。采用CH341A与PIC16F877A构建单片机与计算机之间的USB通讯电路，软件遵循RS232通讯协议，硬件进行电平转换。实际使用表明，这两款产品与计算机端Windows 操作系统下的串口应用程序完全兼容，且通讯过程中无握手失败现象。 Abstract: To solve the problem that current computer serial communication only with USB interface can not satisfy with the old type equipments or MCU to communicate with RS232， two kinds of RS232/USB circuit were designed.CH341A and MAX223 integrated circuit chips were used to create a standard 9-line RS232/USB universal interface convertor without programme. CH341A and PIC16F877A chips were adopted to build the USB communication circuit between computers and MCU. The software follows RS232 communication protocol， and the hardware converts electrical levels. Actual practices indicate that the two manufactures are compatible with serial application program of Windows operation system completely，and get avoid of handshake lost.
上传时间： 2013-11-03
上传用户：siying
为提高电容测量精度，针对电容式传感器的工作原理设计了基于PIC16LF874单片机电容测量模块。简单阐述了电容测量电路的应用背景和国内外研究现状，介绍了美国Microchip公司PIC16LF874单片机的特性。电容式传感器输出的动态微弱电容信号通过PS021型电容数字转换器把模拟量数据转换成数字量数据，所测数据由PIC16LF874单片机应用程序进行处理、显示和保存。实验结果表明，固定电容标称值为10~20 pF 的测量值相对误差在1%以内，同时也可知被测电容容值越大，测量值和标称值相对误差越小。 Abstract: To improve the accuracy of capacitance measurement，aimed at the principle of work of mercury capacitance acceleration transducer，the design of micro capacitance measurement circuit is based on the key PIC16LF874 chip. Briefly discusses the application of the capacitance measuring circuit for the background and status of foreign researchers，focusing on the United States PIC16LF874 microcontroller features. Capacitive sensor outputed signal through the dynamics of weak PS021-chip capacitors （capacitancedigital converter） to convert analog data into digital data，the measured data from the PIC16LF874 microcontroller application process， display and preservation. Experimental results show that the fixed capacitor 10pF ~ 20pF nominal value of the measured value of relative error is within 1%，but also it canbe seen the value of the measured capacitance larger，measuring value and the nominal value of relative error smaller.
上传时间： 2013-10-29
上传用户：wojiaohs
生活中许多目标的高度和水平距离需要进行测量。目前主要的测量方法，仍以传统的皮尺丈量为主，测量效率不高，有时还很不方便，没有技术成熟的数字式测高测距产品。以基本的数学方法为理论依据，利用遥控小车做为载体，采用角度传感器测量角度、霍尔传感器测量水平距离等，通过单片机LM3S615进行数据计算，实现了对待测目标物体的高度、水平距离等数据的快速、精确和数字式的测量，高度测量精度可达99.06%，水平测量精度则可达98.06%。 Abstract: In our lives， the height and horizontal distance of some goals are needed to be measured. Because the currently used methods are still traditional tape-based measuring methods， and the measuring efficiency is low and inconvenient so some kinds of digital and portable measuring methods or instruments are needed. Based on the basic math theory， this paper designed and manufactured a portable， digital and remote controlled measuring mobile small vehicle， which assembled with angle measuring sensor for angle measurement and Hall sensor for horizontal distance measuring. MCU LM3S615 calculated the height and horizontal distance data gotten from these sensors. The measuring process is simple， the measuring results are more accurate and the measuring efficiency is higher than traditional measure instruments. The accuracy of height and distance measurement can reach 99.06% and 98.06%.
上传时间： 2013-10-30
上传用户：jackandlee
提出一种基于凌阳单片机的步进电机加减速的控制方法。采用凌阳科技推出的16位结构工控单片机SPMC75F2413A为控制器，由Allegro公司生产的两相步进电机专用驱动器件SLA7042M构成步进电机的驱动电路，在传统的3段直线加减速控制算法基础上增加至7段S形曲线加减速过程，控制步进电机的启动和停止。实验结果表明，该控制方法克服了直线加减速中不连续、易造成系统冲击的问题，整个系统实现柔性控制，电机启动、停止连续性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
上传时间： 2013-12-08
上传用户：jiangfire
