针对嵌入式机器视觉系统向独立化、智能化发展的要求，介绍了一种嵌入式视觉系统--智能相机。基于对智能相机体系结构、组成模块和图像采集、传输和处理技术的分析，对国内外的几款智能相机进行比较。综合技术发展现状，提出基于FPGA+DSP模式的硬件平台，并提出智能相机的发展方向。分析结果表明，该系统设计可以实现脱离PC运行，完成图像获取与分析，并作出相应输出。 Abstract: This paper introduced an embedded vision system-intelligent camera ，which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture， component modules and image acquisition， transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad， the paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design， the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.
上传时间： 2013-11-14
上传用户：无聊来刷下
针对传统集成电路（ASIC）功能固定、升级困难等缺点，利用FPGA实现了扩频通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核实现NCO模块，在下变频模块调用了硬核乘法器并引入CIC滤波器进行低通滤波，给出了DQPSK解调的原理和实现方法，推导出一种简便的引入?仔/4固定相移的实现方法。采用模块化的设计方法使用VHDL语言编写出源程序，在Virtex-II Pro 开发板上成功实现了整个系统。测试结果表明该系统正确实现了STEL-2000A的核心功能。 Abstract: To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was designed by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
上传时间： 2013-11-19
上传用户：neu_liyan
为了在CDMA系统中更好地应用QDPSK数字调制方式，在分析四相相对移相（QDPSK)信号调制解调原理的基础上，设计了一种QDPSK调制解调电路，它包括串并转换、差分编码、四相载波产生和选相、相干解调、差分译码和并串转换电路。在MAX+PLUSⅡ软件平台上，进行了编译和波形仿真。综合后下载到复杂可编程逻辑器件EPM7128SLC84-15中，测试结果表明，调制电路能正确选相，解调电路输出数据与QDPSK调制输入数据完全一致，达到了预期的设计要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was designed based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上传时间： 2013-10-28
上传用户：jyycc
波长信号的解调是实现光纤光栅传感网络的关键，基于现有的光纤光栅传感器解调方法，提出一种基于FPGA的双匹配光纤光栅解调方法，此系统是一种高速率、高精度、低成本的解调系统，并且通过引入双匹配光栅有效地克服了双值问题同时扩大了检测范围。分析了光纤光栅的测温原理并给出了该方案软硬件设计，综合考虑系统的解调精度和FPGA的处理速度给出了基于拉格朗日的曲线拟合算法。 Abstract: Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network， based on several existing methods of fiber grating sensor demodulation inadequate， a two-match fiber grating demodulation method was presented. This system is a high-speed， high precision， low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA，this paper gives the curve fitting algorithm based on Lagrange.
上传时间： 2013-10-10
上传用户：zxc23456789
为了提高直接转矩控制（DTC）系统定子磁链估计精度，降低电流、电压测量的随机误差，提出了一种基于扩展卡尔曼滤波（EKF）实现异步电机转子位置和速度估计的方法。扩展卡尔曼滤波器是建立在基于旋转坐标系下由定子电流、电压、转子转速和其它电机参量所构成的电机模型上，将定子电流、定子磁链、转速和转子角位置作为状态变量，定子电压为输入变量，定子电流为输出变量，通过对磁链和转速的闭环控制提高定子磁链的估计精度，实现了异步电机的无速度传感器直接转矩控制策略，仿真结果验证了该方法的可行性,提高了直接转矩的控制性能。 Abstract: In order to improve the Direct Torque Control（DTC） system of stator flux estimation accuracy and reduce the current， voltage measurement of random error， a novel method to estimate the speed and rotor position of asynchronous motor based on extended Kalman filter was introduced. EKF was based on d-p axis motor and other motor parameters （state vector: stator current， stator flux linkage， rotor angular speed and position； input: stator voltage； output: staror current). EKF was designed for stator flux and rotor speed estimation in close-loop control. It can improve the estimated accuracy of stator flux. It is possible to estimate the speed and rotor position and implement asynchronous motor drives without position and speed sensors. The simulation results show it is efficient and improves the control performance.
上传时间： 2015-01-02
上传用户：qingdou
微电脑型RS-485显示电表（24*48mm/48*96mm） 特点： 5位数RS-485显示电表 显示范围-19999-99999位數 通訊协议Modbus RTU模式 宽范围交直流兩用電源設計 尺寸小,穩定性高 主要规格： 显示范围:-19999~99999 digit RS-485传输速度: 19200/9600/4800/2400 selective RS-485通讯位址: "01"-"FF" RS-485通讯协议: Modbus RTU mode 显示幕: Red high efficiency LEDs high 10.16 mm (0.4") (MMX-RS-11X) Red high efficiency LEDs high 20.32 mm (0.8") (MMX-RS-12X) Red high efficiency LEDs high 10.16 mm (0.4")x2 (MMX-RS-22X) 参数设定方式: Touch switches 记忆方式: Non-volatile E²PROM memory 绝缘耐压能力: 2KVac/1 min. (input/power) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2015-01-03
上传用户：feitian920
微电脑型单相交流集合式电表（单相二线系统） 特点： 精确度0.25%满刻度±1位数 可同时量测与显示交流电压,電流,頻率,瓦特,(功率因數/視在功率) 交流電壓,電流,瓦特皆為真正有效值(TRMS) 交流電流,瓦特之小數點可任意設定 瓦特單位W或KW可任意設定 CT比可任意設定(1至999) 輸入與輸出絕緣耐压 2仟伏特/1分鐘( 突波測試強度4仟伏特(1.2x50us) 數位RS-485界面 (Optional) 主要规格： 精确度: 0.1% F.S.±1 digit (Frequency) 0.25% F.S.±1 digit(ACA,ACV,Watt,VA) 0.25% F.S. ±0.25o(Power Factor) (-.300~+.300) 输入负载: <0.2VA (Voltage) <0.2VA (Current) 最大过载能力: Current related input: 3 x rated continuous 10 x rated 30 sec. 25 x rated 3sec. 50 x rated 1sec. Voltage related input: maximum 2 x rated continuous 过载显示: "doFL" 显示值范围: 0~600.0V(Voltage) 0~999.9Hz(Frequency)(<20% for voltage input) 0~19999 digit adjustable(Current,Watt,VA) 取样时间: 2 cycles/sec. RS-485通讯位址: "01"-"FF" RS-485传输速度: 19200/9600/4800/2400 selective RS-485通信协议: Modbus RTU mode 温度系数: 100ppm/℃ (0-50℃) 显示幕: Red high efficiency LEDs high 10.16 mm(0.4") 参数设定方式: Touch switches 记忆型式: Non-volatile E²PROM memory 绝缘抗阻: >100Mohm with 500V DC 绝缘耐压能力: 2KVac/1 min. (input/output/power) 1600 Vdc (input/output) 突波测试: ANSI c37.90a/1974,DIN-IEC 255-4 impulse voltage 4KV(1.2x50us) 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2015-01-03
上传用户：几何公差
集合式直流电能表（小功率的） 特点： 精确度0.05%满刻度±1位数 可同时量测与显示/直流电压/电流/瓦特（千瓦）/瓦特小时（千瓦小时） 电压输入（DC0-99.99V/0-600.0V）自动变档功能 显示范围0-9999(电流/瓦特/千瓦),0至99999999(八位數瓦特小时)可任意规划 数位RS-485 界面 (Optional) 主要规格： 辅助电源消耗功率：＜0.35VA(DC12V/DC24V) ＜0.5VA（DC48V） ＜1.5VA（AC90-240V(50/60Hz)） 精确度: 0.05% F.S. ±1 digit (23 ±5℃) 输入范围：Auto range(DC0-99.99V/0-600.0V(DC voltage)) 输入抗阻：＞5MΩ（DC voltage） 取样时间：10 cycles/second(total) 过载显示: " doFL " 显示值范围: 0-9999 digit（DCA/W(KW)） 0-9999999.999 digit(WH/(KWH)) RS-485传输速度: 19200/9600/4800/2400 selective RS-485通讯位址: "01"-"FF"（0-255） RS-485通信协议: Modbus RTU mode 温度系数: 50ppm/℃ (0-50℃) 显示幕:Bight Red LEDs high 10.16 mm(0.4") 参数设定方式: Touch switches 记忆方式: Non-volatile E²PROM memory 绝缘耐压能力:2KVac/1min.(input/output)（RS-485(Isolating)） 1600 Vdc (input/output) （RS-485(Isolating)） 使用环境条件: 0-50℃(20 to 90% RH non-condensed) 存放环境条件: 0-70℃(20 to 90% RH non-condensed) CE认证: EN 55022:1998/A1:2000 Class A EN 61000-3-2:2000 EN 61000-3-3:1995/A1:2001 EN 55024:1998/A1:2001
上传时间： 2013-11-20
上传用户：s363994250
基于通用集成运算放大器，利用MASON公式设计了一个多功能二阶通用滤波器，能同时或分别实现低通、高通和带通滤波，也能设计成一个正交振荡器。电路的极点频率和品质因数能够独立、精确地调节。电路使用4个集成运放、2个电容和11个电阻，所有集成运放的反相端虚地。利用计算机仿真电路的通用滤波功能、极点频率和品质因数的独立控制和正交正弦振荡，从而证明该滤波器正确有效。 Abstract: A new multifunctional second-order filter based on OPs was presented by MASON formula. Functions， such as high-pass， band-pass， low-pass filtering， can be realized respectively and simultaneously， and can become a quadrature oscillator by modifying resistance ratio. Its pole angular frequency and quality factor can be tuned accurately and independently. The circuit presented contains four OPs， two capacitors， and eleven resistances， and inverting input of all OPs is virtual ground. Its general filtering， the independent control of pole frequency and quality factor and quadrature sinusoidal oscillation were simulated by computer， and the result shows that the presented circuit is valid and effective.
上传时间： 2013-10-09
上传用户：13788529953
在Multisim 10软件环境下，设计一种由运算放大器构成的精确可控矩形波信号发生器，结合系统电路原理图重点阐述了各参数指标的实现与测试方法。通过改变RC电路的电容充、放电路径和时间常数实现了占空比和频率的调节，通过多路开关投入不同数值的电容实现了频段的调节，通过电压取样和同相放大电路实现了输出电压幅值的调节并提高了电路的带负载能力，可作为频率和幅值可调的方波信号发生器。Multisim 10仿真分析及应用电路测试结果表明，电路性能指标达到了设计要求。 Abstract: Based on Multisim 10， this paper designed a kind of rectangular-wave signal generator which could be controlled exactly composed of operational amplifier， the key point was how to implement and test the parameter indicators based on the circuit diagram. The duty and the frequency were adjusted by changing the time constant and the way of charging and discharging of the capacitor， the width of frequency was adjusted by using different capacitors provided with multiple switch， the amplitude of output voltage was adjusted by sampling voltage and using in-phase amplifier circuit，the ability of driving loads was raised， the circuit can be used as squarewave signal generator whose frequency and amplitude can be adjusted. The final simulation results of Multisim 10 and the tests of applicable circuit show that the performance indicators of the circuit meets the design requirements.
上传时间： 2014-01-21
上传用户：shen007yue
