提出一种基于凌阳单片机的步进电机加减速的控制方法。采用凌阳科技推出的16位结构工控单片机SPMC75F2413A为控制器，由Allegro公司生产的两相步进电机专用驱动器件SLA7042M构成步进电机的驱动电路，在传统的3段直线加减速控制算法基础上增加至7段S形曲线加减速过程，控制步进电机的启动和停止。实验结果表明，该控制方法克服了直线加减速中不连续、易造成系统冲击的问题，整个系统实现柔性控制，电机启动、停止连续性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
上传时间： 2013-12-08
上传用户：jiangfire
单片机作为一种微型计算机，其内部具有一定的存储单元（8031除外），但由于其内部存储单元及端口有限，很多情况下难以满足实际需求。为此介绍一种新的扩展方法，将数据线与地址线合并使用，通过软件控制的方法实现数据线与地址线功能的分时转换，数据线不仅用于传送数据信号，还可作为地址线、控制线，用于传送地址信号和控制信号，从而实现单片机与存储器件的有效连接。以单片机片外256KB数据存储空间的扩展为例，通过该扩展方法，仅用10个I/O端口便可实现，与传统的扩展方法相比，可节约8个I/O端口。 Abstract: As a micro-computer,the SCM internal memory has a certain units(except8031),but because of its internal storage units and the ports are limited,in many cases it can not meet the actual demand.So we introduced a new extension method,the data line and address lines combined through software-controlled approach to realize the time-conversion functions of data lines and address lines,so the data lines not only transmited data signals,but also served as address lines and control lines to transmit address signals and control signals,in order to achieve an effective connection of microcontroller and memory chips.Take microcontroller chip with256KB of data storage space expansion as example,through this extension method,with only10I/O ports it was achieved,compared with the traditional extension methods,this method saves8I/O ports.
上传时间： 2014-12-26
上传用户：adada
在深入了解Flash存储器的基础上，采用单片机自动检测存储器无效块。主要通过读取每一块的第1、第2页内容，判断该块的好坏，并给出具体的实现过程，以及部分关键的电路原理图和C语言程序代码。该设计最终实现单片机自动检测Flash坏块的功能，并通过读取ID号检测Flash的性能，同时该设计能够存储和读取1GB数据。 Abstract: On the basis of in-depth understanding the Flash chips，this paper designs a new program which using the SCM to detect the invalid block.Mainly through reading the data of the first and second page to detect the invalid block.Specific implementation procedure was given,and the key circuit schematic diagram and C language program code was introduced.This design achieved the function of using the MCU checks the invalid block finally，and increased the function by reading the ID number of Flash to get the performance of the memory.And the design also can write and read1GB data
上传时间： 2013-10-25
上传用户：taozhihua1314
为提高太阳能的利用率，以ATmega8单片机为控制核心，设计了一套光电跟踪与视日运动轨迹跟踪互补控制的双轴太阳跟踪器。该跟踪器在晴天时，利用光敏电阻采集光强判断太阳位置,控制步进电机实现光电跟踪；在阴天时，采集时钟器件PCF8583的时间信息,计算当前太阳位置来实现视日运动轨迹跟踪。实验表明：该太阳跟踪器能在不同天气状况下对太阳进行较准确地跟踪，能量接收效率提高了30%，达到充分利用太阳能的目的。 Abstract: To improve the utilization rate of solar energy，a kind of solar tracking controller which effectively combined the sun angle tracking and photo electric tracking based on ATmega8is designed.In the sunny days，the solar tracking con-troller determines the sun's position by using photosensitive resistances to collect light intensity and control stepper motors to achieve photo electric tracking，n cloudy days，it collects clock chip PCF8583time information to calculate the current position of the sun and achieve the sun angle tracking.Experimental results show the solar tracking controller accurately tracks the sun in different weather conditions，improves received energy efficiency by30%and reaches the purpose of full use of solar energy.
上传时间： 2013-10-15
上传用户：urgdil
设计一种基于ATmega16L单片机的温度控制系统，阐述该系统的软硬件设计方案。采用模块化设计方法，利用增量式PID算法使被控对象的温度值趋于给定值。实验结果表明该系统具有良好的检测和控制功能。 Abstract: This paper designs a temperature control system based on ATmega16L，describes the hardware and software de－sign scheme of the system，adopts the modularized design method and utilizes the incremental PID algorithm to realize the temperature of controlled device incline to the given value.The experiment result indicates that the system has good detec－tion and control function
上传时间： 2013-10-09
上传用户：stvnash
为提高温度测量效率，降低系统的成本，扩展传输距离，设计出一种新型温度采集系统。单片机通过控制具有单总线方式的温度传感器DS18B20实现对温度的测量，同时单片机通过控制具有单总线方式300～450MHz频率范围内的MAX7044与MAX7033无线发射与接收芯片实现温度数据的无线传输。与传统温度采集系统相比，该系统利用单总线方式连接，采用无线传输方式实现远距离通信，易于系统的集成与扩展。实验结果表明，该系统结构简单、方便移植，能够同时实现多达上百点温度的测量与500m范围的传输。 Abstract: To improve the temperature measurement efficiency and reduce system cost,expansion of transmission distance,a new type of temperature acquisition system is designed.Microcontroller controlled temperature sensor DS18B20which has a single-bus achieves temperature measurement,while microcontroller by controlled the MAX7044and MAX7033chip with a single-bus and having300~450MHz radiofrequency to achieve the wireless transmission of temperature data.Compared with conventional temperature acquisition system,the system uses single-bus connected,and uses wireless transmission means to achieve long-distance communications,easy-to-system integration and expansion.The experimental results show that the system is simple,convenient transplantation,and can be implemented in as many as a hundred-point temperature measure-ment and the transmission range of500meters.
上传时间： 2013-10-29
上传用户：515414293
设计一种基于P89V51RD2的功率因数测量仪，采用光电隔离器和专用数码管驱动器。该测量仪是以增强型单片机P89V51RD2为核心，大大简化系统硬件设计。而软件部分采用模块化设计思想，采用中值滤波和小数补偿算法，实现功率因数的高精度测量。实验测试表明，该功率因数测量仪测量精度高，运行稳定可靠。 Abstract: A power－factor measurement instrument based on P89V51RD2is designed，which uses optical coupler and specific LED drive chip.The power factor measurement instrument uses P89V51RD2as a core of which greatly simplifies the system design.Furthermore，modularization software is developed in detail.The high precision power－factor measuring system is realized by the center value filter and fractional compensation algorithm.Experiments manifests that the power－ factor measurement instrument is high precision，steady and reliable.
上传时间： 2014-12-27
上传用户：CHINA526
首先研究CAN总线和SAE J1939协议，提出一种基于MC9S12HZ256微控制器的总线式汽车数字仪表解决方案。详细介绍SAE J1939协议的报文帧格式及应用层协议中发动机相关参数的定义，以及步进电机及其驱动和车速信号的处理方法。该数字仪表系统硬件平台由微处理器和信号采集和信息处理及显示等模块组成。软件设计部分编程实现了对CAN总线和各传感器数据的读取、处理。该系统能够实时反映车辆工况。 Abstract: In this paper，CAN bus and SAE J1939protocol are researched，and a vehicle digital instrument solution based on MC9S12HZ256MCU is proposed.The message frame format and some engine-related parameters’definition in SAE J1939application layer protocol are introduced in detail.Stepper motor and its driver，the methods of speed signal process-ing are also introduced.The hardware platform of vehicle digital instrument is composed by MCU，signal acquisition mod-ule，and signal processing and displaying module.Data receiving and processing from CAN bus and sensors are accom-plished by programming，and vehicle condition can be reflected in real-time.
上传时间： 2013-10-20
上传用户：huannan88
详细介绍工控软件组态王与单片机多机串口通讯的设计原理。分析组态王提供的直接与单片机串口通信方法的优点，给出系统基于RS-485总线传输的接口电路原理图。根据组态王提供的通讯协议和单片机多机串口通讯的原理，给出程序设计流程与思路。 Abstract: In this paper，the design principle of communication between multi-SCM and KingView by serial ports is described in detail.We analysis the advantage of method supplied by KingView,by which KingView can communicate with serial ports of SCM directly，and provide the system’s interface circuit based on the RS-485transmission line.We provide flow diagram of programming and thinking on the basis of communication protocol supplied by KingView and principle of communication among multi-SCM through serial ports.
上传时间： 2013-12-19
上传用户：tecman
针对目前汽车追尾事件频发问题，提出一种防汽车车前和车后追尾的安全装置设计。该设计以高性能、低功耗的8位AVR微处理器ATmega8L为核心，结合霍尔式车速传感器、激光雷达测距装置和MMA7260QT加速度传感器，能够兼顾车前和车后，摒弃以往设计中只考虑车前或车后单一性缺点，尤其适用于高速、夜晚或新手行车。 Abstract: Aiming at the high frequency of vehicle rear-end collision，a safe device design of anti-vehicle rear-end collision is presented.In the design，the high-performance，low-power8-bit AVR microprocessor ATmega8L is utilized as a core combined with Hall-type speed sensor，laser-radar ranging devices and the acceleration sensor MMA7260QT.The design considers both the front and back of a car，and overcomes the drawbacks of former designs in which only the front or the back of the car is considered，so it is especially suitable for high-speed，night or the beginner’s driving.
上传时间： 2013-10-14
上传用户：GavinNeko
