sfrmat is a Matlab function that provides a spatial frequency response* (SFR) from a digital image file containing a slanted-EDGE feature. The specific EDGE-gradient algorithm follows the intent of the standard ISO 12233, developed by Technical Committee ISI/TC 42, for resolution measurements for electronic still pictorial cameras.
标签： frequency function provides response
上传时间： 2014-01-20
上传用户：qunquan
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising EDGE. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上传时间： 2013-12-13
上传用户：himbly
Top module name : SHIFTER (File name : SHIFTER.v) 2. Input pins: SHIFT [3:0], IN [15:0], SIGN, RIGHT. 3. Output pins: OUT [15:0]. 4. Input signals generated from test pattern are latched in one cycle and are synchronized at clock rising EDGE. 5. The SHIFT signal describes the shift number. The shift range is 0 to 15. 6. When the signal RIGHT is high, it shifts input data to right. On the other hand, it shifts input data to left. 7. When the signal SIGN is high, the input data is a signed number and it shifts with sign extension. However, the input data is an unsigned number if the signal SIGN is low. 8. You can only use following gates in Table I and need to include the delay information (Tplh, Tphl) in your design.
上传时间： 2014-01-20
上传用户：三人用菜
ST32 基于（英蓓特）STM32V100的EXTI程序 This example shows how to configure an external interrupt line. In this example, the EXTI line 9 is configured to generate an interrupt on each falling EDGE. In the interrupt routine a led connected to PC.06 is toggled. This led will be toggled due to the softawre interrupt generated on EXTI Line9 then at each falling EDGE.
标签： configure interrupt external example
上传时间： 2016-11-17
上传用户：GavinNeko
selects the mux channel and configures the MAX197 for second write pulse, written with ACQMOD = 0, termi- either unipolar or bipolar input range. A write pulse (WR nates acquisition and starts conversion on WR°Os risin + CS) can either start an acquisition interval or initiate a EDGE (Figure 6). However, if the second control byte combined acquisition plus conversion. The sampling contains ACQMOD = 1, an indefinite acquisition interval interval occurs at the end of the acquisition interval. is restarted. The ACQMOD bit in the input control byte offer
标签： configures the selects channel
上传时间： 2013-12-09
上传用户：
selects the mux channel and configures the MAX197 for second write pulse, written with ACQMOD = 0, termi- either unipolar or bipolar input range. A write pulse (WR nates acquisition and starts conversion on WR°Os risin + CS) can either start an acquisition interval or initiate a EDGE (Figure 6). However, if the second control byte combined acquisition plus conversion. The sampling contains ACQMOD = 1, an indefinite acquisition interval interval occurs at the end of the acquisition interval. is restarted. The ACQMOD bit in the input control byte offer
标签： configures the selects channel
上传时间： 2016-12-24
上传用户：朗朗乾坤
selects the mux channel and configures the MAX197 for second write pulse, written with ACQMOD = 0, termi- either unipolar or bipolar input range. A write pulse (WR nates acquisition and starts conversion on WR°Os risin is restarted. The ACQMOD bit in the input control byte offer+ CS) can either start an acquisition interval or initiate a EDGE (Figure 6). However, if the second control byte combined acquisition plus conversion. The sampling contains ACQMOD = 1, an indefinite acquisition interval interval occurs at the end of the acquisition interval.
标签： configures the selects channel
上传时间： 2016-12-24
上传用户：yzhl1988
97 law to enhance the classic procedure Ridge wavelet extraction Modulus maximum for the wavelet EDGE detection Small spectral analysis method mallat classic procedure
标签： wavelet extraction the procedure
上传时间： 2014-01-09
上传用户：xg262122
1.an fpga implementation of the image space reconstruction algorithm for hyperspectral imaging analysis 2. fpga implemention of a median filter 3. fpga implementation of digital filters 4.hardware acceleration of EDGE detection algorithm on fpgas 5.implementation and evaluation of image processing algorithms on reconfigurable architecture using C-based hardware descriptive languages 6. implementing 2D median filter in fpgas 7.视频图像处理与分析的网络资源
标签： implementation reconstruction hyperspectral algorithm
上传时间： 2014-01-10
上传用户：894898248
c pgm to find redundant paths in a graph.Many fault-tolerant network algorithms rely on an underlying assumption that there are possibly distinct network paths between a source-destination pair. Given a directed graph as input, write a program that uses depth-first search to determine all such paths. Note that, these paths are not vertex-disjoint i.e., the vertices may repeat but they are all EDGE-disjoint i.e., no two paths have the same EDGEs. The input is the adjacency matrix of a directed acyclic graph and a pair(s) of source and destination vertices and the output should be the number of such disjoint paths and the paths themselves on separate lines. In case of multiple paths the output should be in order of paths with minimum vertices first. In case of tie the vertex number should be taken in consideration for ordering.
标签： fault-tolerant algorithms redundant underlyin
上传时间： 2013-12-18
上传用户：jkhjkh1982
