针对使用硬件描述语言进行设计存在的问题，提出一种基于FPGA并采用DSP Builder作为设计工具的数字信号处理器设计方法。并按照Matlab/Simulink/DSP Builder/QuartusⅡ设计流程，设计了一个12阶FIR 低通数字滤波器，通过Quartus 时序仿真及嵌入式逻辑分析仪SignalTapⅡ硬件测试对设计进行了验证。结果表明，所设计的FIR 滤波器功能正确，性能良好。 Abstract: Aiming at the problems in designing DSP using HDL，a method of designing DSP based on FPGA which using DSP Builder as DESigned tool is pointed out.A 12-order low-pass FIR digital filter was DESigned according to the process of Matlab/Simulink/DSP Builder/QuartusⅡ, and the design was verified by the timing simulation based on QuartusⅡand practical test based on SignalTapⅡ. The result shows the DESigned filter is correct in function and good in performance.
上传时间： 2013-11-17
上传用户：lo25643
在综合分析谐波励磁无刷同步发电机励磁控制系统的基础上,对其励磁控制策略进行了研究,开发了一套基于DSP( TMS320F2812) 控制的新型柴油发电机励磁控制系统,该系统采用参数自适应模糊PID 控制励磁,选用交流采样方式实时检测各信号的瞬时特性,系统仿真结果以及在1 台25 kW 工频柴油发电机上的试验结果证明了该控制器具有较好的电压调节特性,系统稳态和暂态性能完全满足发电机对励磁系统的要求。关键词:励磁调节;模糊PID 控制;数字信号处理器;交流采样 Abstract :According to the general analysis of the excitation cont rol system of the harmonious wave excitation brushless synchronous generator and it s characteristics ,a new type of diesel generator excitation cont rol system based on DSP( TMS320F2812) was DESigned. An adaptive fuzzy PID cont rol of excitation is used in this system. To detect the t ransient characteristics of the signals in a timely manner ,AC sampling was applied.The system simulation result s and the testing result s f rom a 25 kW diesel generator (50 Hz) can prove that the voltage regulation characteristics of the excitation cont rol system are very well ,and both the steadyOstate performance and the t ransient performance of the generator are also good.Key words :excitation cont rol ;fuzzy PID cont rol ;digital signal processor (DSP) ;AC sampling
上传时间： 2013-10-29
上传用户：fxf126@126.com
设计一种应用于某全地形ATV车载武器装置中的中控系统，该系统设计是以TMS320F2812型DSP为核心，采用模块化设计思想，对其硬件部分进行系统设计，能够完成对武器装置高低、回转方向的运动控制，实现静止或行进状态中对目标物的测距，自动瞄准以及按既定发射模式发射弹丸和各项安全性能检测等功能。通过编制相应的软件，对其进行系统调试，验证了该设计运行稳定。 Abstract: A central control system applied to an ATV vehicle weapons is DESigned. The system design is based on TMS320F2812 DSP as the core， uses modular design for its hardware parts. The central control system can complete the motion control of the level of weapons and equipment， rotation direction， to achieve a state of static or moving objects on the target ranging， auto-targeting and according to the established target and the projectile and the launch of the security performance testing and other functions. Through the development of appropriate software and to carry out system testing to verify the stability of this design and operation.
上传时间： 2013-11-02
上传用户：jshailingzzh
针对传统集成电路（ASIC）功能固定、升级困难等缺点，利用FPGA实现了扩频通信芯片STEL-2000A的核心功能。使用ISE提供的DDS IP核实现NCO模块，在下变频模块调用了硬核乘法器并引入CIC滤波器进行低通滤波，给出了DQPSK解调的原理和实现方法，推导出一种简便的引入?仔/4固定相移的实现方法。采用模块化的设计方法使用VHDL语言编写出源程序，在Virtex-II Pro 开发板上成功实现了整个系统。测试结果表明该系统正确实现了STEL-2000A的核心功能。 Abstract: To overcome drawbacks of ASIC such as fixed functionality and upgrade difficulty, FPGA was used to realize the core functions of STEL-2000A. This paper used the DDS IP core provided by ISE to realize the NCO module, called hard core multiplier and implemented CIC filter in the down converter, described the principle and implementation detail of the demodulation of DQPSK, and derived a simple method to introduce a fixed phase shift of ?仔/4. The VHDL source code was DESigned by modularity method , and the complete system was successfully implemented on Virtex-II Pro development board. Test results indicate that this system successfully realize the core function of the STEL-2000A.
上传时间： 2013-11-06
上传用户：liu123
为了在CDMA系统中更好地应用QDPSK数字调制方式，在分析四相相对移相（QDPSK)信号调制解调原理的基础上，设计了一种QDPSK调制解调电路，它包括串并转换、差分编码、四相载波产生和选相、相干解调、差分译码和并串转换电路。在MAX+PLUSⅡ软件平台上，进行了编译和波形仿真。综合后下载到复杂可编程逻辑器件EPM7128SLC84-15中，测试结果表明，调制电路能正确选相，解调电路输出数据与QDPSK调制输入数据完全一致，达到了预期的设计要求。 Abstract: In order to realize the better application of digital modulation mode QDPSK in the CDMA system， a sort of QDPSK modulation-demodulation circuit was DESigned based on the analysis of QDPSK signal modulation-demodulation principles. It included serial/parallel conversion circuit, differential encoding circuit, four-phase carrier wave produced and phase chosen circuit, coherent demodulation circuit, difference decoding circuit and parallel/serial conversion circuit. And it was compiled and simulated on the MAX+PLUSⅡ software platform,and downloaded into the CPLD of EPM7128SLC84-15.The test result shows that the modulation circuit can exactly choose the phase，and the output data of the demodulator circuit is the same as the input data of the QDPSK modulate. The circuit achieves the prospective requirement of the design.
上传时间： 2014-01-13
上传用户：qoovoop
a8259 可编程中断控制 altera提供 The a8259 is DESigned to simplify the implementation of the interrupt interface in 8088 and 8086 based microcomputer systems. The device is known as a programmable interrupt controller. The a8259 receives and prioritizes up to 8 interrupts, and in the cascade mode, this can be expanded up to 64 interrupts. An asynchronous reset and a clock input have been added to improve operation and reliability.
上传时间： 2014-11-29
上传用户：zhyiroy
针对飞行模拟器座舱数据采集的复杂性，设计了一种基于以太网分布式的数据采集控制系统，该系统是RCM5700微处理器模块上的以太网应用。在系统的基础上具体讨论了PoE技术的应用，在传输数据的网线上同时提供电流，提出并实现了一种包括辅助电源在内的完整可靠的PoE供电方案。设计采用美国国家半导体的LM5073和LM5576并根据不同的负载情况，进行稳定可靠的电压转换，以满足数据采集电路的要求。实验结果表明：该设计稳定可靠，满足低于13 W的采集节点供电要求，提高了模拟器信号采集系统的通用性和标准化程度，避免了以往数据采集节点单独繁琐的电源设计。 Abstract: Aiming at the complexity of large avion simulation and controlling，the simulator cabin distribute data collecting and control system was DESigned. This system is the application of RCM5700 on Ethernet. Based on this system，PoE technique that makes Ethernet can also provide power were expounded with emphasis and included FAUX design the PoE resolution was realized. To achieve the requirement of this system，LM5073 and LM5576 were used to DC-DC switch. From the data of experiment，the design filled the requirement of power-need of node whose power was lower than 13W. The application of the technique can advance the degree of simulation data collections currency and standardization and avoid designing additional power system.
上传时间： 2013-11-09
上传用户：xyipie
A Computer-On-Module, or COM, is a Module with all components necessary for a bootable host computer, packaged as a super component. A COM requires a Carrier Board to bring out I/O and to power up. COMs are used to build single board computer solutions and offer OEMs fast time-to-market with reduced development cost. Like integrated circuits, they provide OEMs with significant freedom in meeting form-fit-function requirements. For all these reasons the COM methodology has gained much popularity with OEMs in the embedded industry. COM Express® is an open industry standard for Computer-On-Modules. It is DESigned to be future proof and to provide a smooth transition path from legacy parallel interfaces to LVDS (Low Voltage Differential Signaling) interfaces. These include the PCI bus and parallel ATA on the one hand and PCI Express and Serial ATA on the other hand.
上传时间： 2013-11-05
上传用户：Wwill
The CC1101 is a low-cost sub- 1 GHztransceiver DESigned for very low-powerwireless applications. The circuit is mainlyintended for the ISM (Industrial, Scientific andMedical) and SRD (Short Range Device)frequency bands at 315, 433, 868, and 915MHz, but can easily be programmed foroperation at other frequencies in the 300-348MHz, 387-464 MHz and 779-928 MHz bands.CC1101 is an improved and code compatibleversion of the CC1100 RF transceiver. Themain improvements on the CC1101 include:
上传时间： 2013-11-12
上传用户：363186
6小时学会labview, labview Six Hour Course – Instructor Notes This zip file contains material DESigned to give students a working knowledge of labview in a 6 hour timeframe. The contents are: Instructor Notes.doc – this document. labviewIntroduction-SixHour.ppt – a PowerPoint presentation containing screenshots and notes on the topics covered by the course. Convert C to F (Ex1).vi – Exercise 1 solution VI. Convert C to F (Ex2).vi – Exercise 2 solution subVI. Thermometer-DAQ (Ex2).vi – Exercise 2 solution VI. Temperature Monitor (Ex3).vi – Exercise 3 solution VI. Thermometer (Ex4).vi – Exercise 4 solution subVI. Convert C to F (Ex4).vi – Exercise 4 solution subVI. Temperature Logger (Ex4).vi – Exercise 4 solution VI. Multiplot Graph (Ex5).vi – Exercise 5 solution VI. Square Root (Ex6).vi – Exercise 6 solution VI. State Machine 1 (Ex7).vi – Exercise 7 solution VI. The slides can be presented in two three hour labs, or six one hour lectures. Depending on the time and resources available in class, you can choose whether to assign the exercises as homework or to be done in class. If you decide to assign the exercises in class, it is best to assign them in order with the presentation. This way the students can create VI’s while the relevant information is still fresh. The notes associated with the exercise slide should be sufficient to guide the students to a solution. The solution files included are one possible solution, but by no means the only solution.
标签： labview
上传时间： 2013-10-13
上传用户：zjwangyichao
