虫虫首页| 资源下载| 资源专辑| 精品软件
登录| 注册

ControlLER

  • 基于VHDL的微型打印机控制器设计

    介绍基于VHDL的微型打印机控制器的设计。论述了微型打印机的基本原理,以及实现控制器的VHDL语言设计。打印机的数据来自系统中的存储模块,根据需要控制打印。该微型打印机控制器可取代传统的微型打印机,且抗干扰性好,可靠性高,具有较强的移植性,稍加改动就可应用于不同场合。 Abstract:  This paper introduced the design method of micro printer ControlLER based on VHDL.The basic principles of microprinter is explained,as well as the realization of the ControlLER by VHDL language.The printer data is from the system memory modules,can control printer.The design of microprinter ControlLER has antigood and high reliability,it can replace the traditional printer.The ControlLER has very good portability,and need little modify that can use in different situation.

    标签: VHDL 微型打印机 制器设计

    上传时间: 2013-11-03

    上传用户:dudu1210004

  • NXP P89LPC901单片机汽车起动保护控制器设计

    在汽车发动机起动时,若发动机起动后起动机不能及时断电,将会烧毁起动机或损坏飞轮齿环;若变速器不在空档位置起动,则起动机的瞬间动力将使汽车位移,还可能引起交通事故和人身安全。为此介绍一种利用NXP P89LPC901单片机控制的汽车起动保护控制器,通过检测汽车起动开关、变速箱档位、发动机转速,实现对汽车发动机起动过程检测和保护。起动保护控制器在发动机起动过程中通过采用逐个关闭打开负载系统,解决汽车发动机过程中因起动电流大而对汽车电源的冲击影响,延长了电瓶寿命。 Abstract:  When the automotive engine is started, the engine start motor and flywheel gear may be damaged, even traffic accidents and personal safeties may be caused by wrong operation or other factors.In order to ensure the automotive engine can be started normally and safely,it is necessary that the protecting measures and methods are considered in the automotive electrical control system.This paper introduces a kind of the automotive engine starting protect ControlLER based on NXP P89LPC901 MCU.The ControlLER can protect the engine starting process by detecting the starter key switch,transmission stall and engine speed.Through the use of close and open load system,the ControlLER can solve the impact on automotive power because of the high-current load in the process of the automobile engine starting, and extend battery life.

    标签: NXP LPC 901 P89

    上传时间: 2013-10-15

    上传用户:mikesering

  • 基于C8051F020的触摸屏驱动控制

    C8051F020单片机通过SPI接口驱动四线电阻式触摸屏控制器TSC2046,利用中断方式驱动TSC2046设计软件。介绍了触摸屏的工作原理、TSC2046工作方式以及典型应用电路。 Abstract:  The C8051F020 MCU is connected with the TSC2046 which is a 4-wire touch screen ControlLER. The TSC2046 is controlled by interrupt mode, the? operation principle of touch screen is introduced. The operation mode of TSC2046 and typical application circuit are also discussed.

    标签: C8051F020 触摸屏 驱动控制

    上传时间: 2014-12-27

    上传用户:hwl453472107

  • 基于C8051F340的数据采集器设计

    针对众多低成本数据采集需求,采用带有片上USB控制器和D/A转换器的混合信号微处理器C8051F340,设计了一款可通过USB接口和LabVIEW图形用户界面实现与PC机联机的数据采集器,同时借助系统的SD卡存储独立实现现场长时间采集数据。该数据采集器成本低,结构简单,体积小,已成功用于工业现场。 Abstract:  Aiming at the need of low cost data acquisition, a data acquisition device is designed based on C8051F340 which is a mixed-signal microControlLER and integrates USB ControlLER and A/D ControlLER on a chip.The data acquisition device which can combine with PC by USB interface and LabVIEW graphical user interface,can realize data acquisition. At the same time,it can be solely run a long time in virtue of SD card in field.The date aequisition device features low cost,simple structure and little sharp, and it has been used in industry field.

    标签: C8051F340 数据 集器设计

    上传时间: 2014-05-31

    上传用户:1109003457

  • 基于UC3854A控制的PFC中分岔现象仿真研究

       为深入了解基于UC3854A控制的PFC变换器中的动力学特性,研究系统参数变化对变换器中分岔现象的影响,在建立Boost PFC变换器双闭环数学模型的基础上,用Matlab软件对变换器中慢时标分岔及混沌等不稳定现象进行了仿真。在对PFC变换器中慢时标分岔现象仿真的基础上,分析了系统参数变化对分岔点的影响,并进行了仿真验证。仿真结果清晰地显示了输入整流电压的幅值变化对系统分岔点的影响。 Abstract:  In order to better understand the dynamics characteristic of power factor correction converter based on UC3854A, and make the way that parameters change influences the bifurcation phenomena of the system clearly. The math model of the two closed loop circuits to the Boost PFC (Power Factor Correction) converter ControlLER was built. Then, with the help of Matlab, the simulation for nonlinear phenomena such as chaos and slow-scale bifurcation in the PFC converter was made. Finally the factors that have influence to the phenomenon of bifurcation under slow-scale in PFC converter were analyzed. The simulation results clearly show the parameters change influences the bifurcation point of the system.

    标签: 3854A 3854 PFC UC

    上传时间: 2013-10-17

    上传用户:杜莹12345

  • LS7266R1在电子式万能材料试验机中的应用

    针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移,一般采用光电轴角编码器检测位置信号,输出正交编码脉冲信号。若采用其他方法检测位置信号,必然导致电路设计复杂,可靠性降低。因此,提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理,LS7266R1与单片机的接口硬件设计,以及主程序软件流程图。巧妙地把力量传感器,位移传感器等机械运动状态的压力或拉力以及位置坐标,变成了电压信号和电脉冲数字信号,供A/D测量和LS7266R1计数,从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract:  Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore, the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods, will inevitably lead to the circuit design complexity, reliability decreased. The work theory of the ControlLER, the hardware interface design between LS7266R1 and single chip, and the flow chart of main program, are presented in this paper. The signal of the compression or tension power and displacement at working, which tested by power sensor and displacement sensor especially, is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself, or controlled by the COM command of PC.

    标签: 7266R 7266 LS R1

    上传时间: 2013-11-02

    上传用户:yl1140vista

  • 基于P89LPC922单片机的汽车后车窗控制器设计

    介绍一种应用于长城赛弗SUV汽车后门车窗多功能控制器,能实现对电动玻璃车窗、车窗雨刮器、喷水器以及电加热除霜器等控制。介绍了基于NXP P89LPC922单片机多功能汽车后车窗控制器的控制功能、硬件电路原理和软件设计方法。 Abstract:  This paper presents a multipurpose automotive rear windows ControlLER for CHANGCHENG SAFE SUV.The ControlLER can control rear power-operated window,rear wiping,washing water pump and rear defroster of the windows. In this paper, it is introduced in detail that the functions and the design of the circuit and program of the ControlLER based on NXP P89LPC922 MCU.

    标签: P89 LPC 922 89

    上传时间: 2013-11-13

    上传用户:z754970244

  • 基于ATmega168的ADC按键设计

    利用Atmel公司的ATmega168微处理器,采用A/D转换方式来实现按摩椅控制器的键盘接口,通过在硬件电路中巧妙地选择电阻,在软件设计中采用数字滤波、二分法和区间鉴定等方法,灵敏可靠地实现了按摩椅中30个按键的处理。给出了硬件电路设计和软件设计思想以及部分汇编代码。 Abstract:  This paper chooses A/D conversion method to realize the keyboard interface of the ControlLER by using ATmega168 microchip from Atmel Company.It accomplishes 30-key dealing sensitively and reliably in massage chair through skillfully selecting resistors in hardware circuit and using digital filter,dichotomy and area-judging method in software design.The hardware design circuit, software design idea and partly assembles code are presented mainly.

    标签: ATmega 168 ADC 按键

    上传时间: 2014-01-10

    上传用户:咔乐坞

  • 基于C8051F系列单片机的无线收发电路设计

    基于幅移键控技术ASK(Amplitude-Shift Keying),以C8051F340单片机作为监测终端控制器,C8051F330D单片机作为探测节点控制器,采用半双工的通信方式,通过监控终端和探测节点的无线收发电路,实现数据的双向无线传输。收发电路采用直径为0.8 mm的漆包线自行绕制成圆形空心线圈天线,天线直径为(3.4±0.3)cm。试验表明,探测节点与监测终端的通信距离为24 cm,通过桥接方式,节点收发功率为102 mW时,节点间的通信距离可达20 cm。与传统无线收发模块相比,该无线收发电路在受体积、功耗、成本限制的场合有广阔的应用前景。 Abstract:  Based on ASK technology and with the C8051F340 and C8051F330D MCU as the ControlLER, using half-duplex communication mode, this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter (3.4±0.3) cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm,the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules, the circuit has wide application prospect in small size, low cost and low power consumption and other characteristics.

    标签: C8051F 单片机 无线收发 电路设计

    上传时间: 2013-10-19

    上传用户:xz85592677

  • PCF8578 LCD图形点阵液晶驱动器芯片简介及封装库

    The PCF8578 is a low power CMOS1 LCD row and column driver, designed to drive dotmatrix graphic displays at multiplex rates of 1:8, 1:16, 1:24 or 1:32. The device has40 outputs, of which 24 are programmable and configurable for the following ratios ofrows/columns: 32¤8, 24¤16, 16¤24 or 8¤32. The PCF8578 can function as a stand-alone LCDControlLER and driver for use in small systems. For larger systems it can be used inconjunction with up to 32 PCF8579s for which it has been optimized. Together these twodevices form a general purpose LCD dot matrix driver chip set, capable of driving displaysof up to 40960 dots. The PCF8578 is compatible with most microControlLERs andcommunicates via a two-line bidirectional bus (I2C-bus). Communication overhead isminimized by a display RAM with auto-incremented addressing and display bankswitching.

    标签: 8578 PCF LCD 图形点阵

    上传时间: 2013-10-23

    上传用户:顶得柱