All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low and high levels, even if anundefined voltage level (between TTL-VIL and TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, and can not be properly used in anapplication to suppress signal noise, and to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL and VIH with a sufficient rise/fall time, as generally usualand specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input and theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, and no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.
上传时间： 2014-04-02
上传用户：han_zh
This application note demonstrates how to write an Inter Integrated Circuit bus driver (I2C) for the XA-S3 16-bitMicrocontroller from Philips Semiconductors.Not only the driver software is given. This note also contains a set of (example) interface routines and a smalldemo application program. All together it offers the user a quick start in writing a complete I2C system applicationwith the PXAS3x.The driver routines support interrupt driven single master transfers. Furthermore, the routines are suitable foruse in conjunction with real time operating systems.
上传时间： 2013-11-02
上传用户：zw380105939
I2C interface, is a very powerful tool for system designers. Theintegrated protocols allow systems to be completely software defined.Software development time of different products can be reduced byassembling a library of reusable software modules. In addition, themultimaster capability allows rapid testing and alignment ofend-products via external connections to an assembly-line computer.The mask programmable 87LPC76X and its EPROM version, the87LPC76X, can operate as a master or a slave device on the I2Csmall area network. In addition to the efficient interface to thededicated function ICs in the I2C family, the on-board interfacefacilities I/O and RAM expansion, access to EEPROM andprocessor-to-processor communications.
标签： microcontro Using 76X LPC
上传时间： 2013-12-30
上传用户：Artemis
//芯片资料请到www.elecfans.com查找 //DS1820 C51 子程序//这里以11.0592M晶体为例，不同的晶体速度可能需要调整延时的时间//sbit DQ =P2^1;//根据实际情况定义端口 typedef unsigned char byte;typedef unsigned int word; //延时void delay(word useconds){ for(;useconds>0;useconds--);} //复位byte ow_reset(void){ byte presence; DQ = 0; //pull DQ line low delay(29); // leave it low for 480us DQ = 1; // allow line to return high delay(3); // wait for presence presence = DQ; // get presence signal delay(25); // wait for end of timeslot return(presence); // presence signal returned} // 0=presence, 1 = no part //从 1-wire 总线上读取一个字节byte read_byte(void){ byte i; byte value = 0; for (i=8;i>0;i--) { value>>=1; DQ = 0; // pull DQ low to start timeslot DQ = 1; // then return high delay(1); //for (i=0; i<3; i++); if(DQ)value|=0x80; delay(6); // wait for rest of timeslot } return(value);} //向 1-WIRE 总线上写一个字节void write_byte(char val){ byte i; for (i=8; i>0; i--) // writes byte, one bit at a time { DQ = 0; // pull DQ low to start timeslot DQ = val&0x01; delay(5); // hold value for remainder of timeslot DQ = 1; val=val/2; } delay(5);} //读取温度char Read_Temperature(void){ union{ byte c[2]; int x; }temp; ow_reset(); write_byte(0xCC); // Skip ROM write_byte(0xBE); // Read Scratch Pad temp.c[1]=read_byte(); temp.c[0]=read_byte(); ow_reset(); write_byte(0xCC); //Skip ROM write_byte(0x44); // Start Conversion return temp.x/2;}
上传时间： 2013-11-03
上传用户：hongmo
#include <reg51.h>#include<intrins.h> #define BUSY1 (DQ1==0) sbit DQ1 = P0^4; unsigned char idata TMP; unsigned char idata TMP_d; unsigned char f; void wr_ds18_1(char dat);unsigned char rd_ds18_1(); /***************延时程序，单位us,大于10us*************/void time_delay(unsigned char time){ time=time-10; time=time/6; while(time!=0)time--;} /*****************************************************//* reset ds18b20 *//*****************************************************/void ds_reset_1(void){ unsigned char idata count=0; DQ1=0; time_delay(240); time_delay(240); DQ1=1; return;}
上传时间： 2013-10-29
上传用户：sssnaxie
基于变频调速的水平连铸机拉坯辊速度控制系统Frequency Inverter Based Drawing RollerS peedC ontrolSy stem ofHorizontal Continuous Casting MachineA 伟刘冲旅巴(南 华 大 学电气工程学院，衡阳421001)摘要拉坯辊速度控制是水平连铸工艺的关键技术之一，采用变频器实现水平连铸机拉坯辊速度程序控制，由信号发生装置给变频器提供程控信号。现场应用表明该控制系统速度响应快，控制精度高，满足了水平连铸生产的需要。关键词水平连铸拉坯辊速度程序控制变频器Absh'act Speedc ontorlof dr awingor leris on eo fth ek eyte chnologiesfo rho rizontalco ntinuousca stingm achine.Fo rth ispu rpose,fr equencyco nverterisad optedfo rdr awingor lersp eedp rogrammablec ontorlof ho rizontalco ntinuousca stingm achine,th ep rogrammableco ntorlsi gnalto fr equencyc onverteris provided场a signal generator. The results of application show that the response of system is rapid and the control accuracy is high enough to meet thedemand of production of horizontal continuous casting.Keywords Horizontalco ntinuousc asting Drawingor ler Speedp rogrammablec ontrol Ferquencyin verter 随着 现 代 化工业生产对钢材需求量的日益增加，连铸生产能力已经成为衡量一个国家冶金工业发展水平的重要指标之一。近十几年来，水平连铸由于具有投资少、铸坯直、见效快等多方面的优点，国内许多钢铁企业利用水平连铸机来浇铸特种合金钢，发挥了其独特的优势并取得了较好的经济效益〔1,2)0采用 水 平 连铸机浇铸特种合金钢时，由于拉坯机是水平连铸系统中的关键设备之一，拉坯机及其控制性能的好坏直接影响着连铸坯的质量，因此，连铸的拉坯技术便成为整个水平连铸技术的核心。由于钢的冶炼过程是在高温下进行的，钢水温度的变化又容易影响铸坯的质量和成材率，因此，如何能在高温环境下控制好与铸坯速度相关的参数(拉、推程量，中停时间和拉坯频率等)对于确保连铸作业的进一步高效化，延长系统的连续作业时间十分关键。因此，拉坯辊速度控制技术是连铸生产过程控制领域中的关键技术之- [31
上传时间： 2013-10-12
上传用户：gxy670166755
PLC TM卡开发系统汇编程序(ATM8051) ;***************** 定义管脚*************************SCL BIT P1.0SDA BIT P1.1GC BIT P1.2BZ BIT P3.6LEDI BIT P1.4LEDII BIT P1.5OK BIT 20H.1OUT1 BIT P1.3OUT2 BIT P1.0OUT3 BIT P1.1RXD BIT P3.0TXD BIT P3.1PCV BIT P3.2WPC BIT P3.3RPC BIT P3.5LEDR BIT P3.4LEDL BIT P3.6TM BIT P3.7;********************定义寄存器***********************ROMDTA EQU 30H;NUMBY EQU 61H;SLA EQU 60H;MTD EQU 2FH;MRD EQU 40H;TEMP EQU 50H;;ORG 00H;;INDEX:MOV P1, #00H;MOV P2, #0FFHMOV MTD ,#00HCALL REEMOV R0,40HCJNE R0,#01,NO;MOV P2,#1CHLJMP VIMEN MOV P2,#79HACALL TOUCHRESET ;JNC NO ;CALL READTM ;CJNE A,#01H,NO;NOPMOV MTD, #00HCALL WEENOPMOV P2,#4AHSETB BZCALL TIMECLR BZMOV PCON, #0FFHVIME:CALL TIME1CALL TOUCHRESETJNC VIMECALL READTMCJNE A, #01H,VIME;NOPNOPNOPIII: MOV MTD,#00HCALL REECALL BBJNB OK,NO1LJMP ZHUNO1:MOV MTD,#10H
上传时间： 2014-03-24
上传用户：448949
用单片机配置FPGA—PLD设计技巧 Configuration/Program Method for Altera Device Configure the FLEX Device You can use any Micro-Controller to configure the FLEX device–the main idea is clocking in ONE BITof configuration data per CLOCK–start from the BIT 0The total Configuration time–e.g. 10K10 need 15K byte configuration file•calculation equation–10K10* 1.5= 15Kbyte–configuration time for the file itself•15*1024*8*clock = 122,880Clock•assume the CLOCK is 4MHz•122,880*1/4Mhz=30.72msec
上传时间： 2013-10-09
上传用户：a67818601
自动检测80C51 串行通讯中的波特率本文介绍一种在80C51 串行通讯应用中自动检测波特率的方法。按照经验，程序起动后所接收到的第1 个字符用于测量波特率。这种方法可以不用设定难于记忆的开关，还可以免去在有关应用中使用多种不同波特率的烦恼。人们可以设想：一种可靠地实现自动波特检测的方法是可能的，它无须严格限制可被确认的字符。问题是：在各种的条件下，如何可以在大量允许出现的字符中找出波特率的定时间隔。显然，最快捷的方法是检测一个单独位时间（single bit time），以确定接收波特率应该是多少。可是，在RS-232 模式下，许多ASCII 字符并不能测量出一个单独位时间。对于大多数字符来说，只要波特率存在合理波动（这里的波特率是指标准波特率），从起始位到最后一位“可见”位的数据传输周期就会在一定范围内发生变化。此外，许多系统采用8 位数据、无奇偶校验的格式传输ASCII 字符。在这种格式里，普通ASCII 字节不会有MSB 设定
上传时间： 2013-10-15
上传用户：shirleyYim
传统的人工耳蜗语音处理器采用ASIC设计，投入成本高，可移植性差，设计了一种基于TMS320VC5509A的人工耳蜗语音处理器。该处理器采用双麦克风接受语音信号，实现了语音信号的自适应噪声消除和CIS （Continuous Interleaved Sampling） 方案。同一段语音由DSP采样处理得到的刺激脉冲与MATLAB采样处理的结果基本相同。实验结果表明，基于DSP的人工耳蜗语音处理器能实现语音信号中噪声的消除并得到良好的刺激脉冲。
上传时间： 2013-10-22
上传用户：23333
