为满足无线网络技术具有低功耗、节点体积小、网络容量大、网络传输可靠等技术要求，设计了一种以MSP430单片机和CC2420射频收发器组成的无线传感节点。通过分析其节点组成，提出了ZigBee技术中的几种网络拓扑形式，并研究了ZigBee路由算法。针对不同的传输要求形式选用不同的网络拓扑形式可以尽大可能地减少系统成本。同时针对不同网络选用正确的ZigBee路由算法有效地减少了网络能量消耗，提高了系统的可靠性。应用试验表明，采用ZigBee方式通信可以提高传输速率且覆盖范围大，与传统的有线通信方式相比可以节约40%左右的成本。 Abstract: To improve the proposed technical requirements such as low-ower， small nodes， large capacity and reliable network transmission， wireless sensor nodes based on MSP430 MCU and CC2420 RF transceiver were designed. This paper provided network topology of ZigBee technology by analysing the component of the nodes and researched ZigBee routing algorithm. Aiming at different requirements of transmission mode to choose the different network topologies form can most likely reduce the system cost. And aiming at different network to choose the correct ZigBee routing algorithm can effectively reduced the network energy consumption and improved the reliability of the system. Results show that the communication which used ZigBee mode can improve the transmission rate， cover more area and reduce 40% cost compared with traditional wired communications mode.
上传时间： 2013-10-09
上传用户：robter
针对UHF读写器设计中，在符合EPC Gen2标准的情况下，对标签返回的高速数据进行正确解码以达到正确读取标签的要求，提出了一种新的在ARM平台下采用边沿捕获统计定时器数判断数据的方法，并对FM0编码进行解码。与传统的使用定时器定时采样高低电平的FM0解码方法相比，该解码方法可以减少定时器定时误差累积的影响；可以将捕获定时器数中断与数据判断解码相对分隔开，使得中断对解码影响很小，实现捕获与解码的同步。通过实验表明，这种方法提高了解码的效率，在160 Kb/s的接收速度下，读取一张标签的时间约为30次/s。 Abstract: Aiming at the requirement of receiving correctly decoded data from the tag under high-speed communication which complied with EPC Gen2 standard in the design of UHF interrogator， the article introduced a new technology for FM0 decoding which counted the timer counter to judge data by using the edge interval of signal capture based on the ARM7 platform. Compared with the traditional FM0 decoding method which used the timer timed to sample the high and low level， the method could reduce the accumulation of timing error and could relatively separate capture timer interrupt and the data judgment for decoding， so that the disruption effect on the decoding was small and realizd synchronization of capture and decoding. Testing result shows that the method improves the efficiency of decoding， at 160 Kb/s receiving speed， the time of the interrogator to read a tag is about 30 times/s.
上传时间： 2013-11-10
上传用户：liufei
The LPC1850/30/20/10 are ARM Cortex-M3 based microcontrollers for embeddedapplications. The ARM Cortex-M3 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC1850/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals. The ARMCortex-M3 CPU also includes an internal prefetch unit that supports speculativebranching.The LPC1850/30/20/10 include up to 200 kB of on-chip SRAM data memory, a quad SPIFlash Interface (SPIFI), a State Configuration Timer (SCT) subsystem, two High-speedUSB controllers, Ethernet, LCD, an external memory controller, and multiple digital andanalog peripherals.
上传时间： 2014-12-31
上传用户：zhuoying119
The LPC4350/30/20/10 are ARM Cortex-M4 based microcontrollers for embeddedapplications. The ARM Cortex-M4 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC4350/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals, andincludes an internal prefetch unit that supports speculative branching. The ARMCortex-M4 supports single-cycle digital signal processing and SIMD instructions. Ahardware floating-point processor is integrated in the core.The LPC4350/30/20/10 include an ARM Cortex-M0 coprocessor, up to 264 kB of datamemory, advanced configurable peripherals such as the State Configurable Timer (SCT)and the Serial General Purpose I/O (SGPIO) interface, two High-speed USB controllers,Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals
上传时间： 2013-10-28
上传用户：15501536189
The correct answer for each test bank question is highlighted in bold. Test bank questions are based on the end-of-chapter questions. If a student studies the end-of-chapter questions (which are linked to the italicized words in each chapter), then they will be successful on the test bank questions.
上传时间： 2014-12-31
上传用户：旗鱼旗鱼
This white paper discusses how market trends, the need for increased productivity, and new legislation have accelerated the use of safety systems in industrial machinery. This TÜV-qualified FPGA design methodology is changing the paradigms of safety designs and will greatly reduce development effort, system complexity, and time to market. This allows FPGA users to design their own customized safety controllers and provides a significant competitive advantage over traditional microcontroller or ASIC-based designs. Introduction The basic motivation of deploying functional safety systems is to ensure safe operation as well as safe behavior in cases of failure. Examples of functional safety systems include train brakes, proximity sensors for hazardous areas around machines such as fast-moving robots, and distributed control systems in process automation equipment such as those used in petrochemical plants. The International Electrotechnical Commission’s standard, IEC 61508: “Functional safety of electrical/electronic/programmable electronic safety-related systems,” is understood as the standard for designing safety systems for electrical, electronic, and programmable electronic (E/E/PE) equipment. This standard was developed in the mid-1980s and has been revised several times to cover the technical advances in various industries. In addition, derivative standards have been developed for specific markets and applications that prescribe the particular requirements on functional safety systems in these industry applications. Example applications include process automation (IEC 61511), machine automation (IEC 62061), transportation (railway EN 50128), medical (IEC 62304), automotive (ISO 26262), power generation, distribution, and transportation. 图Figure 1. Local Safety System
上传时间： 2013-11-14
上传用户：zoudejile
面向Eclips的Nios II软件构建工具手册 The Nios® II Software Build Tools (SBT) for Eclipse™ is a set of plugins based on the Eclipse™ framework and the Eclipse C/C++ development toolkit (CDT) plugins. The Nios II SBT for Eclipse provides a consistent development platform that works for all Nios II embedded processor systems. You can accomplish all Nios II software development tasks within Eclipse, including creating, editing, building, running, debugging, and profiling programs.
上传时间： 2013-11-02
上传用户：瓦力瓦力hong
Nios II 软件开发人员手册中的缓存和紧耦合存储器部分 Nios® II embedded processor cores can contain instruction and data caches. This chapter discusses cache-related issues that you need to consider to guarantee that your program executes correctly on the Nios II processor. Fortunately, most software based on the Nios II hardware abstraction layer (HAL) works correctly without any special accommodations for caches. However, some software must manage the cache directly. For code that needs direct control over the cache, the Nios II architecture provides facilities to perform the following actions:
上传时间： 2013-10-25
上传用户：虫虫虫虫虫虫
Designing withProgrammable Logicin an Analog WorldProgrammable logic devicesrevolutionized digital design over 25years ago, promising designers a blankchip to design literally any functionand program it in the field. PLDs canbe low-logic density devices that usenonvolatile sea-of-gates cells calledcomplex programmable logic devices(CPLDs) or they can be high-densitydevices based on SRAM look-up tables
标签： Solutions Analog Xilinx FPGAs
上传时间： 2013-11-07
上传用户：suicone
MP3 portable players are the trend in music-listening technology. These players do not includeany mechanical movements, thereby making them ideal for listening to music during any type ofactivity. MP3 is a digital compression technique based on MPEG Layer 3 which stores music ina lot less space than current CD technology. Software is readily available to create MP3 filesfrom an existing CD, and the user can then download these files into a portable MP3 player tobe enjoyed in almost any environment.
上传时间： 2013-11-23
上传用户：nanxia
