介绍以P87LPC764型单片机为核心的延时型漏电继电器设计方案。该方案可供用户选择实现额定动作电流和5倍额定动作电流下不同的延时动作时间，并有重合闸设定选择功能。解决了以往传统分立元件带来的延时时间离散性大且不易实现的弊端。 Abstract: In this paper, the delay leakage relay based on P87LPC764 is introduced in detail. This system provides different relay times at rating current and 5× rating current for users and also offers superposition brake set selection function. So that it resolves many traditional problems.
上传时间： 2013-11-08
上传用户：zhaiye
介绍了CAN总线和P87C591单片机的特点，给出了基于P87C591单片机的信号采集节点的软、硬件设计，指出了硬件电路设计中应注意的问题，在软件设计中重点介绍了节点初始化、报文发送和报文接收等子程序。 Abstract: The features of CAN Bus and the microcontroller P87C591 are introduced, and the design of hardware circuit and soft configuration of the signals collection node based on P87C591 are presented. The problems in designing hardware circuit are discussed.Initialization subprogram, transmiting subprogram and receiving subprogram are emphasized in soft configuration.
上传时间： 2013-11-03
上传用户：BIBI
基于幅移键控技术ASK（Amplitude-Shift Keying），以C8051F340单片机作为监测终端控制器，C8051F330D单片机作为探测节点控制器，采用半双工的通信方式，通过监控终端和探测节点的无线收发电路，实现数据的双向无线传输。收发电路采用直径为0.8 mm的漆包线自行绕制成圆形空心线圈天线，天线直径为（3.4±0.3）cm。试验表明，探测节点与监测终端的通信距离为24 cm，通过桥接方式，节点收发功率为102 mW时，节点间的通信距离可达20 cm。与传统无线收发模块相比，该无线收发电路在受体积、功耗、成本限制的场合有广阔的应用前景。 Abstract: Based on ASK technology and with the C8051F340 and C8051F330D MCU as the controller， using half-duplex communication mode， this paper achieves bi-directional data transfer. Transceiver circuit constituted by enameled wire which diameter is 0.8mm and wound into a diameter （3.4±0.3） cm circular hollow coil antenna. Tests show that the communication distance between detection and monitoring of the terminal is 24cm，the distance is up to 20cm between two nodes when using the manner of bridging and the node transceiver power is 102mW. Compared with the conventional wireless transceiver modules， the circuit has wide application prospect in small size， low cost and low power consumption and other characteristics.
上传时间： 2013-10-19
上传用户：xz85592677
在需要实时大量输入汉字的显示控制处理应用中，利用传统单片机实现显示控制的设计方法是较难实现的。带汉字字库的液晶模块的使用使得小容量ROM单片机的大量汉字信息输入与显示成为可能。提出了针对汉字字库编码的二级索引拼音输入检索方法,介绍了以ST7920作为控制器的带汉字字库的液晶显示模块的接口方法及汉字显示和控制原理，给出了通用计算机键盘在单片机中的串行接口，采用该技术可大大增强单片机的汉字输入功能。为小容量ROM单片机的大批量汉字信息处理提供了一种汉字输入解决方案。 Abstract: It is difficult to realize Chinese characters input method based on the embedded system by using the traditional design method of display control. It is possible to input and display Chinese characters based on the embedded system with the ROM of small content by using the LCD module with Chinese characters.Chinese characters input method of the quadric index recall in allusion to Chinese characters code is brought forward.The interface and the principle of Chinese characters display control based on the LCD module controlled with the ST7920 is introduced too.The serial interface of the computer keyboard in common use and the embedded system is given at the same time. It can enhance the embedded system function of Chinese characters input by using this technology, and provide a kind of Chinese characters input scheme for the embedded system with small capacity ROM.
上传时间： 2013-11-19
上传用户：jhksyghr
为解决传统可视倒车雷达视频字符叠加器结构复杂，可靠性差，成本高昂等问题，在可视倒车雷达设计中采用视频字符发生器芯片MAX7456。该芯片集成了所有用于产生用户定义OSD，并将其插入视频信号中所需的全部功能，仅需少量的外围阻容元件即可正常工作。给出了以MAX7456为核心的可视倒车雷达的软、硬件实现方案及设计实例。该方案具有电路结构简单、价格低廉、符合人体视觉习惯的特点。经实际装车测试，按该方案设计的可视倒车雷达视场清晰、提示字符醒目、工作可靠，可有效降低驾驶员倒车时的工作强度、减少倒车事故的发生。 Abstract: A new video and text generation chip，MAX7456，was used in the design of video parking sensor in order to simplify system structure，improve reliability and reduce cost. This chip included all the necessary functions to generate user-defined OSDs and to add them into the video signals. It could be put into work with addition of just a small number of resistances and capacitors. This paper provided software and hardware implementation solutions and design example based on the chip. The system had the characteristics of simplicity in circuit structure，lower cost，and comfort for the nature of human vision. Loading road test demonstrates high video and text display quality and reliable performance，which makes the driver easy to see backward and reduces chance of accidents.
上传时间： 2013-12-10
上传用户：qiaoyue
针对船舶气象仪保障维修而设计的船舶气象仪测试系统，包括信息处理终端、主仪器检测模块、传感器检测模块，各个模块都采用基于AVR单片机的嵌入式系统，模块之间通过CAN总线进行通信。结果表明，船舶气象仪测试系统能够快速检测船舶气象仪故障，与单纯依靠人工方式排查故障相比，故障检测时间缩短了60%以上。 Abstract: The test system of ship meteorological instrument was developed to satisfy the maintenance of ship meteorological instruments，which composed of information processing terminal， testing module of main instrument and testing module of sensors. Each of these modules included an embedded system based on microcontroller of AVR series and communicated with other module by CAN bus. The results show that the test system can judge the fault of ship meteorological instrument quickly and shorten the fault detection time as much as 60% compared with simple manual troubleshooting.
上传时间： 2013-11-23
上传用户：stvnash
将现行的供暖计费方式由按建筑面积计费变为按消耗的热能计费是供暖计费方式发展趋势，为了满足这一计费方式变化的需要，设计了基于IC卡的预付费式新型供暖计费系统，通过测量用户采暖系统进出口的温度和流量，计算用户消耗的热能，利用IC卡记录用户预付费的金额和当年热能的单价，根据热能消耗和当年热能的单价计算用户采暖费，根据实际发生的供暖费用和预付费金额控制供暖的开停，这一计费方式的变化使供暖计费更趋合理。 Abstract: It is trend that the mode of heat charging is changed from billing by building area to by thermal energy. In order to meet the needs of heat charging mode changing， a new system of heat charging based on IC card is proposed. The user?蒺s energy consumption is calculated by measuring the user inlet and outlet temperature and flow，using the IC card to record the prepaid amount and the current price of heat. The user?蒺s heating costs is calculated according to energy consumption and current price， according to actual heating costs and prepaid amount，the system controls the heating opening or stopping. It is more reasonable that calculated heating costs by user heat consumption
上传时间： 2013-10-14
上传用户：大融融rr
提出一种基于单片机AT89C51SND1C的MP3播放系统的设计方案。单片机集成了专用的解码器，使用K9F1208闪存作为外存储器，放音电路采用CS4330，存储文件通过播放器上的USB接口设备从PC机上直接下载，液晶显示采用LCD1602。方案设计简单，性价比高，低功耗，易扩展。由于采用的是通用单片机实现的，可以很容易地移植到其他微控制器系统中，有很强的市场竞争能力和实用价值。 Abstract: A MP3 player design based on microchip AT89C51SND1C was presented, which used K9F1208 Flash chip as the memory circuit and used CS4330 as play chip. Storage files were download from PC through USB interfaces player on the device，and the LCD/602 was used as display screen. This system had characteristics of simple design,low power,easy expand，low cost and high recognition. Using of universual microchip make it easy to transplant to other microcontrol system，and have strong market competitiom and practical value.
上传时间： 2014-12-27
上传用户：佳期如梦
为了在工业生产及过程控制中准确测量温度，设计了一种基于低功耗MSP430单片机的数字温度计。整个系统通过单片机MSP430F1121A控制DS18B20读取温度，采用数码管显示，温度传感器DS18B20与单片机之间通过串口进行数据传输。MSP430系列单片机具有超低功耗，且外围的整合性高，DS18B20只需一个端口即可实现数据通信，连接方便。通过多次实验证明，该系统的测试结果与实际环境温度一致，除了具有接口电路简单、测量精度高、误差小、可靠性高等特点外，其低成本、低功耗的特点使其拥有更广阔的应用前景。 Abstract: In order to obtain accurate measuring temperature in industrial production and process control， a digital thermometer based on MSP430 MCU is designed. The system uses MSP430F1121A MCU to control DS18B20， and gets the temperature data， which is displayed on the LED. The temperature sensor DS18B20 and MCU transmit data through serial communication. MSP430 series has ultra-low power and high integration， DS18B20 only needs one port to achieve data communication. Through many experimental results prove， this system is consistent with actual environment temperature. The system has characteristics of interface circuit simple， high measuring accuracy， minor error， high reliability， besides， the characteristics of low cost and low power make it having vaster application prospect.
上传时间： 2013-10-16
上传用户：wettetw
Bootloader是微处理器上电时运行的第一段代码，它可以通过通信接口实现对微处理器内部应用程序的更新升级，为网络化嵌入式产品的应用程序升级带来极大的便利。由于目前没有统一嵌入式系统的Bootloader。基于NEC 78K0系列单片机自编程原理，设计出一个适用于78K0/Fx2系列单片机的Bootloader，并能够通过单片机串口在线升级应用程序。 Abstract: Bootloader is the first piece of code executed after microprocessor startup. It makes the embedded product’s firmware update conveniently through communication interface. However， no unified bootloader is available for all kinds of microprocessor products. Based on the principle of self-programming NEC 78K0s’ series， a useful Bootloader which is suitable for 78K0/Fx2s’ series MCU is designed，the design can update the application through serial ports.
标签： Bootloader MCU 自编程
上传时间： 2013-10-26
上传用户：fang2010
