WP369可扩展式处理平台-各种嵌入式系统的理想解决方案 ：Delivering unrivaled levels of system performance,flexibility, scalability, and integration to developers,Xilinx's architecture for a new Extensible Processing Platform is optimized for system power, cost, and size. Based on ARM's dual-core Cortex™-A9 MPCore processors and Xilinx’s 28 nm programmable logic,the Extensible Processing Platform takes a processor-centric approach by defining a comprehensive processor system implemented with standard design methods. This approach provides Software Developers a familiar programming environment within an optimized, full featured,powerful, yet low-cost, low-power processing platform.
上传时间： 2013-10-22
上传用户：685
The Xilinx Zynq-7000 Extensible Processing Platform (EPP) redefines the possibilities for embedded systems, giving system and software architects and developers a flexible platform to launch their new solutions and traditional ASIC and ASSP users an alternative that aligns with today’s programmable imperative. The new class of product elegantly combines an industrystandard ARMprocessor-based system with Xilinx 28nm programmable logic—in a single device. The processor boots first, prior to configuration of the programmable logic. This, along with a streamlined workflow, saves time and effort and lets software developers and hardware designers start development simultaneously.
上传时间： 2013-11-01
上传用户：dingdingcandy
针对嵌入式机器视觉系统向独立化、智能化发展的要求，介绍了一种嵌入式视觉系统--智能相机。基于对智能相机体系结构、组成模块和图像采集、传输和处理技术的分析，对国内外的几款智能相机进行比较。综合技术发展现状，提出基于FPGA+DSP模式的硬件平台，并提出智能相机的发展方向。分析结果表明，该系统设计可以实现脱离PC运行，完成图像获取与分析，并作出相应输出。 Abstract: This paper introduced an embedded vision system-intelligent camera ，which was for embedded machine vision systems to an independent and intelligent development requirements. Intelligent camera architecture， component modules and image acquisition， transmission and processing technology were analyzed. After comparing integrated technology development of several intelligent cameras at home and abroad， the paper proposed the hardware platform based on FPGA+DSP models and made clear direction of development of intelligent cameras. On the analysis of the design， the results indicate that the system can run from the PC independently to complete the image acquisition and analysis and give a corresponding output.
上传时间： 2013-10-24
上传用户：bvdragon
波长信号的解调是实现光纤光栅传感网络的关键，基于现有的光纤光栅传感器解调方法，提出一种基于FPGA的双匹配光纤光栅解调方法，此系统是一种高速率、高精度、低成本的解调系统，并且通过引入双匹配光栅有效地克服了双值问题同时扩大了检测范围。分析了光纤光栅的测温原理并给出了该方案软硬件设计，综合考虑系统的解调精度和FPGA的处理速度给出了基于拉格朗日的曲线拟合算法。 Abstract: Sensor is one of the most important application of the fiber grating. Wavelength signal demodulating is the key techniques to carry out fiber grating sensing network， based on several existing methods of fiber grating sensor demodulation inadequate， a two-match fiber grating demodulation method was presented. This system is a high-speed， high precision， low-cost demodulation system. And by introducing a two-match grating effectively overcomes the problem of double value while expands the scope of testing. This paper analyzes the principle of fiber Bragg grating temperature and gives the software and hardware design of the program. Considering the system of demodulation accuracy and processing speed of FPGA，this paper gives the curve fitting algorithm based on Lagrange.
上传时间： 2014-07-24
上传用户：caiguoqing
The Tri-Mode Ethernet MAC (TEMAC) UltraController-II module is a minimal footprint,embedded network processing engine based on the PowerPC™ 405 (PPC405) processor coreand the TEMAC core embedded within a Virtex™-4 FX Platform FPGA. The TEMACUltraController-II module connects to an external PHY through Gigabit Media IndependentInterface (GMII) and Management Data Input/Output (MDIO) interfaces and supports tri-mode(10/100/1000 Mb/s) Ethernet. Software running from the processor cache reads and writesthrough an On-Chip Memory (OCM) interface to two FIFOs that act as buffers between thedifferent clock domains of the PPC405 OCM and the TEMAC.
上传时间： 2013-10-26
上传用户：yuzsu
With the Altera Nios II embedded processor, you as the system designercan accelerate time-critical software algorithms by adding custominstructions to the Nios II processor instruction set. Using custominstructions, you can reduce a complex sequence of standard instructionsto a single instruction implemented in hardware. You can use this featurefor a variety of applications, for example, to optimize software innerloops for digital signal processing (DSP), packet header processing, andcomputation-intensive applications. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphicaluser interface (GUI) used to add up to 256 custom instructions to theNios II processor
上传时间： 2013-11-07
上传用户：swing
该系统以计算机为依托构建中央信息处理系统CIPS（Central Information Processing System），以Pocket PC作为巡检终端PS（Portable Station），采用SQL Server 2000关系型数据库和SQL Server CE3.0嵌入式数据库技术，集RFID技术、GPS定位技术、信息管理、信息传输等多项技术于一体，完成信息在CIPS和PS之间的交互，实现巡检信息的综合处理。
上传时间： 2013-11-16
上传用户：stvnash
提出了一种以ARM微处理器为控制核心的远程无线视频监控终端的设计方案，其监控终端的硬件设计包括视频采集处理、中央管理控制、无线传输3个模块。并给出了监控终端的软件开发平台和开发模式的系统启动代码、嵌入式Linux系统移植以及驱动程序和应用程序。测试结果表明，该监控终端设计方案合理、有效，基本满足监控需求。 Abstract: A remote wireless video monitoring terminal design， which uses ARM microprocessor as its core control， is proposed in this paper.The hardware design of monitoring terminal system is composed of the video acquisition and processing module， the central management and control module， wireless transmission module.Meanwhile the monitoring terminal-s software development platform and development patterns are designed. Also the design of the system-s start codes， embedded Linux system-s transplantation process， driver and the corresponding applications are given. The results showed that the monitoring terminal design is reasonable， effective， basically meet monitoring requirements.
上传时间： 2013-11-13
上传用户：wanqunsheng
The LPC4350/30/20/10 are ARM Cortex-M4 based microcontrollers for embeddedapplications. The ARM Cortex-M4 is a next generation core that offers systemenhancements such as low power consumption, enhanced debug features, and a highlevel of support block integration.The LPC4350/30/20/10 operate at CPU frequencies of up to 150 MHz. The ARMCortex-M4 CPU incorporates a 3-stage pipeline, uses a Harvard architecture withseparate local instruction and data buses as well as a third bus for peripherals, andincludes an internal prefetch unit that supports speculative branching. The ARMCortex-M4 supports single-cycle digital signal processing and SIMD instructions. Ahardware floating-point processor is integrated in the core.The LPC4350/30/20/10 include an ARM Cortex-M0 coprocessor, up to 264 kB of datamemory, advanced configurable peripherals such as the State Configurable Timer (SCT)and the Serial General Purpose I/O (SGPIO) interface, two High-speed USB controllers,Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals
上传时间： 2013-10-28
上传用户：15501536189
ORCAD在使用的时候总会出现这样或那样的问题…但下这个问题比较奇怪…在ORCAD中无法输出网表…弹出下面的错误….这种问题很是奇怪…Netlist Format: tango.dllDesign Name: D:\EDA_PROJECT\PROTEL99SE\YK\SV3200\MAIN.DSNERROR [NET0021] Cannot get part.[FMT0024] Ref-des not found. Possible Logical/Physical annotation conflict.[FMT0018] Errors processing intermediate file找了一天没找到问题…终于在花了N多时间后发现问题所在…其实这个问题就是不要使用ORCAD PSPICE 库里面的元件来画电路图…实际中我是用了PSPICE里面和自己制作的二种电阻和电容混合在一起…就会出现这种问题…
上传时间： 2013-11-21
上传用户：zaocan888
