用单片机控制MAX543,来控制电压的输出
上传时间: 2016-08-02
上传用户:星仔
一个网上的开源项目,用AVR单片机做的舵机,用的是直流电机,电阻反馈,PID控制,是个很好的学习项目
上传时间: 2013-12-19
上传用户:685
包含单片机开发的入门程序,如彩灯、按键、中断、查表等。
上传时间: 2014-01-01
上传用户:chens000
单片机方面大量常用优秀源代码和说明 ACM-12864汉字液晶显示驱动程序 Ad_da转换 ADC0809 adc2051 AD转换类 C51_table DES算法演示 I2c总线 IIC LED显示 编程规范与范例 步进电机 查表 串行通信 打印 代码运算类 代码转换 单片机经验谈 单片机直接驱动液晶显示 电机pwm控制 电机控制 定浮点子程序库 定时与中断 二进制数运算 汇编与c的衔接 键盘扫描程序 键盘与显示 交通灯 抗干扰 滤波 排序 排序类 频率计 软件工程 实用子程序 数字多用表 数字频率计 通讯 显示子程序 延时 移位除 音乐 应用类 源程序 在线下载器源程序 中断应用 自动往返小汽车 51单片机子程序.exe AT90S8515打铃程序.ASM hex2bcd.asm main_last.asm RTX-51 Real-Time(汉).pdf RTX-51 实时操作系统.pdf SOFT_UART.ASM test_read.asm testpw.asm 八月桂花香.asm 单片机C51编程几个有用的模块.htm 单片机实现软件滤波.txt 遥控器程序.txt
上传时间: 2016-08-30
上传用户:cjf0304
、本实战的目的是让大家熟悉ADC模块的功能以及AD转换的方法 2、项目实现的功能:从芯片RA0输入一个可以随时变化的模拟量(通过调节DEMO板VR1实现) 则单片机就能够及时地把该模拟量进行模/数转换,并用LED显示出来,我们可以看到转换结果 会随模拟量的变化而变化,从而以让我们了解片内ADC模块的工作情况。 3、本例的软件设计思路:利用单片机片内硬件资源TMR0和预分频器,为ADC提供定时启动信号。但是 没有利用其中断功能,而是采用了软件查询方式,转换结果采用了右对齐方式, A/D转换的时钟源选用了系统周期的8倍,本例对于ADC的电压基准要求不高, 我们就选用了电源电压VDD和VSS作为基准电压, 4、对于A/D转换过程是否完成也没有利用ADC模块的中断功能,而是以软件方式查询其中启动位GO是否为0。本例中选用的模拟通道为AN0。
上传时间: 2014-01-17
上传用户:离殇
在Quick51实验开发板上51单片机在Keil编译环境下,实现温度和电压的多路循环检测及在8位数码管上循环显示并可受板上的按键1、2、3、8的控制的功能
上传时间: 2013-12-18
上传用户:6546544
Keil C51 上51系列单片机优化的CRC-8 算法。可以自己改其他算式的,包含字节查表,半字节查表,bit计算。很难得的哦。
上传时间: 2014-01-12
上传用户:小鹏
proteus与avr结合开发的单片机程序,实现走表功能
上传时间: 2016-09-04
上传用户:xauthu
是用C语言编写的关于用51单片机控制12864液晶LCD的源程序,适用与交流电压及其谐波的显示
上传时间: 2013-12-25
上传用户:gxf2016
卡车仪表的单片机程序,使用的是ICCAVR环境,用的是ATmega8芯片。
上传时间: 2016-09-21
上传用户:小草123