网站上的算法大都是查512字节表的,对单片机来讲,太浪费空间了。 据老古网上资料,修改并测试通过以下算法:
上传时间: 2016-05-19
上传用户:dengzb84
对于内部具有D /A转换器的单片机,采用其自备的D /A转换器产生需要的信号是最经 济的方法。C8051F020是Cygnal公司最新的一款功能强大的内部具有D /A转换器的单片机。介绍了 采用查表和D /A转换产生正弦波形的方法,详细描述了在C8051F020 D /A转换器上产生正弦信号的 电路和程序。通过修改数据表可以产生方波、三角波或其他任意波形信号。
上传时间: 2014-02-04
上传用户:Late_Li
PROTEUS仿真用单片机系统板 系统资源丰富: ★ 内置RAM 32KB模块 ★ 内置8位动态数码显示模块 ★ 内置8X8点阵显示模块 ★ 4位静态数码显示模块 ★ 4位级联的74LS164串并转换模块 ★ 内置8通道8位A/D转换 ★ 内置8位D/A转换 ★ 内置2路SPI和I2C总线接口 ★ 内置4路1-Wire总线接口 ★ 内置4X4矩阵式键盘 ★ 内置4路独立式键盘 ★ 内置4路拨动开关 ★ 内置8位LED发光二极管 ★ 内置3路0-5V之间可调的电压 ★ 内置音频放大模块 ★ 2路继电器控制模块 ★ 2路4分频模块 ★ 内置RS232通信模块
上传时间: 2014-08-17
上传用户:hustfanenze
温度的BCD码显示 在0809上显视的是电压值,所以必须将电压转换成温度值。LM35传感器的电压温度特性为“10mV/摄氏度”,经放大电路放大四倍后为40mV/摄氏度,因此对于255来说,每个数代表了20mV,也就是说电压值中的每个00000002代表了温度值中的00000001,由此可编出一张BCD码转换表,此部分程序如下:
上传时间: 2014-11-28
上传用户:mikesering
通过单片机按键选择输出信号类型及要求输出量,在LED显示器件上指示信号类型及设定数值.系统工作电源±15V , ±5V 。恒流电流输出0.0~8.0mA, 负载电阻≤500Ω。3. 稳压电压输出0.0~5.0V,电流负载能力≤100mA.电压及电流输出在充许负载范围内误差小于5%FS。电压及电流输出须共用一个输出正端, 输出负端为地。输出电压及电流设定精确到二位十进制数。
上传时间: 2016-06-03
上传用户:wendy15
ptotel画的频率表表头,带4个LED串行显示,附加一个电压转频率的电路版图
上传时间: 2016-06-04
上传用户:372825274
给出一种新型的基于单片机控制的充电模块设计,并从系统的硬件和软件两方面对这种设计作了分析。该系统能通过对输出电压和电流的检测,可以对输出电压和电流进行控制和补偿。可以通过按键对输出参数进行设置,电池电压和充电电流,对电池充电进行监视和管理。
上传时间: 2016-06-16
上传用户:erkuizhang
有关Atmega8的protues的仿真部分,除前言外共六部分: 1.基本IO的学习Led部分; 2.基本IO:按键部分; 3.外部中断; 4.定时,计数器; 5.串口通信; 6.IIC通信。 我是老杨,该文档的作者,这份文档是在学习单片机的时候写的,没有把计划写的写完,但这是当时写的最全的一份了。
上传时间: 2013-12-21
上传用户:stampede
数字电压器,用C51系列单片机制作。用来测电压,并在数码管上数字显示
上传时间: 2013-12-18
上传用户:lifangyuan12
一个AVR单片机的BootLoad程序,现已在Atmega8和Atmega16两种芯片上测试通过
上传时间: 2016-07-30
上传用户:iswlkje