为提高电容测量精度，针对电容式传感器的工作原理设计了基于PIC16LF874单片机电容测量模块。简单阐述了电容测量电路的应用背景和国内外研究现状，介绍了美国Microchip公司PIC16LF874单片机的特性。电容式传感器输出的动态微弱电容信号通过PS021型电容数字转换器把模拟量数据转换成数字量数据，所测数据由PIC16LF874单片机应用程序进行处理、显示和保存。实验结果表明，固定电容标称值为10~20 pF 的测量值相对误差在1%以内，同时也可知被测电容容值越大，测量值和标称值相对误差越小。 Abstract: To improve the accuracy of capacitance measurement，aimed at the principle of work of mercury capacitance acceleration transducer，the design of micro capacitance measurement circuit is based on the key PIC16LF874 chip. Briefly discusses the application of the capacitance measuring circuit for the background and status of foreign researchers，focusing on the United States PIC16LF874 microcontroller features. Capacitive sensor outputed signal through the dynamics of weak PS021-chip capacitors （capacitancedigital converter） to convert Analog data into digital data，the measured data from the PIC16LF874 microcontroller application process， display and preservation. Experimental results show that the fixed capacitor 10pF ~ 20pF nominal value of the measured value of relative error is within 1%，but also it canbe seen the value of the measured capacitance larger，measuring value and the nominal value of relative error smaller.
上传时间： 2013-10-29
上传用户：wojiaohs
详细介绍了TLC1549系列模数转换器的特点及工作原理，然后根据TLC1549的工作时序和A/D转换原理针对实际问题编写了详细的汇编语言程序。 Abstract: A basic principle and characteristic of TLC1549 Analog-to-digital converter are introduced? detailedly in this article.Through engineering-oriented illustration,a microcomputer programmer base on basic principle and time sequence of TLC1549 is writted.
上传时间： 2014-07-16
上传用户：blans
为降低成本和解决现有膜片钳放大器系统中PC机的干扰问题，研究了一种基于单片机的膜片钳放大器小系统。该系统采用ADI公司生产的ADuC841作为控制核心，并且配置相应的液晶显示模块LCM3202401。模拟电路部分采用高输入阻抗的AD8627实现微电流信号的采集，并由后级电路进行信号的放大和电阻电容的补偿。它具有硬件电路简单、体积小、使用方便的特点。既可以单独作为小系统实现采集和显示，也可以通过红外方式和PC机进行通讯，在PC机上进行信号的处理。 Abstract: In order to reduce cost and resolve the interferential problem with PC in existing patch clamp amplifiers, a small patch clamp amplifier system design based on microcontroller is studied. It adopts a new high performance microconverter ADuC841 by the ADI as the control core in the system, configuring a liquid crystal module LCM3202401. In the Analog circuit, AD8627 with high input impedance is used to detect the low current，signal magnification, as well as resistance and capacitance compensation are accomplished by subsequent circuits. It has the advantage of simple hardware circuit design, small volume and convenient operation. It can either be used as an independent system to measure and show signal detected or transmit to PC by infrared ray.
上传时间： 2013-11-06
上传用户：yy_cn
The outputs of the PCA9518 are immediately available as soon as there is a voltage present on thesupply >~1V and behave as described above. The power-on reset of the PCA9518A keeps the outputsturned off during power-up and maintains the high impedance of the outputs throughout the power-upcycle. There is an additional built-in delay after power-up that allows the Analog circuits to stabilize beforethe part is activated.
标签： Replacement 9518 NXP PCA
上传时间： 2013-10-26
上传用户：13817753084
Luminary Micro provides an Analog-to-digital converter (ADC) module on some members of theStellaris microcontroller family. The hardware resolution of the ADC is 10 bits; however, due to noiseand other accuracy-diminishing factors, the true accuracy is less than 10 bits. This application noteprovides a software-based oversampling technique, resulting in an improved Effective Number OfBits (ENOB) in the conversion result. This document describes methods of oversampling an inputsignal, and the impact on precision and overall system performance.
标签： Oversampling Techniques ADC fo
上传时间： 2013-12-17
上传用户：zhyiroy
Luminary Micro Stellaris™ microcontrollers that are equipped with an Analog-to-digital converter(ADC), use an innovative sequence-based sampling architecture designed to be extremely flexible,yet easy to use. This application note describes the sampling architecture of the ADC. Sinceprogrammers can configure Stellaris microcontrollers either through the powerful StellarisFamilyDriver Library or through direct writes to the device's control registers, this application note describesboth methods. The information presented in this document is intended to complement the ADCchapter of the device datasheet, and assumes the reader has a basic understanding of howADCsfunction.
标签： Microcontr Stellaris Using the
上传时间： 2013-10-14
上传用户：blans
基于单DSP的VoIP模拟电话适配器研究与实现:提出和实现了一种新颖的基于单个通用数字信号处理器(DSP)的VoIP模拟电话适配器方案。DSP的I/O和存储资源非常有限，通常适于运算密集型应用，不适宜控制密集型应用[5]。该系统高效利用单DSP的I/O和片内外存储器资源，采用μC/OS-II嵌入式实时操作系统，支持SIP和TCP-UDP/IP协议，通过LAN或者宽带接入，使普通电话机成为Internet终端，实现IP电话。该系统软硬件结构紧凑高效，运行稳定，成本低，具有广阔的应用前景。关键词：模拟电话适配器；IP电话；数字信号处理器；μC/OS-II 【Abstract】This paper presents a VoIP ATA solution based on a single digital signal processor (DSP). DSPs are suitable for arithmetic-intensiveapplication and unsuitable for control-intensive application because of the limitation of I/O and memory resources. This solution is based on a 16-bitfixed-point DSP and μC/OS-II embedded real-time operating system. It makes good use of the limited resources, supports SIP and TCP-UDP/IPprotocol. It can connect the Analog telephone to Internet and realize the VoIP application. This system has a great future for its high efficiency andlow cost.【Key words】Analog telephone adapter (ATA); Voice over Internet protocol (VoIP); Digital signal processor (DSP); μC/OS-II Research and Implementation of VoIPATA Based on Single DSP
上传时间： 2013-11-20
上传用户：Wwill
计算机应用中，有时需处理的信息不是数字量，而是一些随时间连续变化的模拟量，甚至是一些非电量，如温度、压力、速度等。模拟量的存储处理困难。首先将非电的模拟信号变成与之对应的模拟电信号，这要通过各种传感器来完成。计算机可处理的信息均是数字量（电脉冲信号）1和0，必须把要处理的模拟电量转换成数字化的电信号，这需要模拟(Analog)与数字(Digital)转换电路。数字到模拟转换:(Digital to Analog Convert, D/A) D/A转换电路是模拟电路加上电子开关。D/A转换电路的核心是一个运算放大器。运算放大器的特性:(Operation Amplifier) K->无穷大， V和->0 传递函数：V0 = -Vi * R0/Ri Ii->0, I和=If梯形R-2R电阻网络D/A转换器Ki受一个8位二进制代码控制 某位为1，对应开关K倒向右边； 某位为0，对应开关K倒向左边。Ki不论倒向哪边，均为接地VA-VH 的电位为： VREF，1/2VREF，..1/128VREFVO= -VREF *（1/2K7+1/4K6+…+1/256K0）V0= -（0-255/256）VREF 8位D/A转换器DAC0830系列器件国家半导体公司（NS)产品，0830、0831、0832。R-2R梯形电阻网络D/A转换器，双缓冲结构。单电源、低功耗、电流建立时间1uS。与微计算机接口方便。8位D/A转换器DAC0830系列器件ILE： 输入锁存允许； WR1#： 加载IN REG； WR2#: 加载DAC REG； XFER#: IN REG传到DAC REG； Iout1,Iout2: 外接OA输入； Rfb: 反馈电阻接OA输出； VREF： 参考电源，控制输出电压变化范围。
标签： AD转换
上传时间： 2013-10-16
上传用户：lu2767
PK51是为8051系列单片机所设计的开发工具，支持所有8051系列衍生产品，，支持带扩展存储器和扩展指令集（例如Dallas390/5240/400,Philips 51MX,Analog Devices MicroConverters）的新设备,以及支持很多公司的一流的设备和IP内核,比如Analog Devices, Atmel, Cypress Semiconductor, Dallas Semiconductor, Goal, Hynix, Infineon, Intel, NXP(founded by Philips), OKI, Silicon Labs,SMSC, STMicroeleectronics,Synopsis, TDK, Temic, Texas Instruments,Winbond等。通过PK51专业级开发工具，可以轻松地了解8051的On-chip peripherals与及其它关键特性。
上传时间： 2013-10-09
上传用户：1109003457
The SDI standards are the predominant standards for uncompressed digital videointerfaces in the broadcast studio and video production center. The first SDI standard,SD-SDI, allowed standard-definition digital video to be transported over the coaxial cableinfrastructure initially installed in studios to carry Analog video. Next, HD-SDI wasto support high-definition video. Finally, dual link HD-SDI and 3G-SDIdoubled the bandwidth of HD-SDI to support 1080p (50 Hz and 60 Hz) and other videoformats requiring more bandwidth than HD-SDI provides.
上传时间： 2013-10-08
上传用户：yjj631
