Radio Frequency Integrated Circuit Design I enjoyed reading this book for a number of reasons. One reason is that itaddresses high-speed analog design in the context of microwave issues. This isan advanced-level book, which should follow courses in basic circuits andtransmission lines. Most analog integrated circuit designers in the past workedon applications at low enough frequency that microwave issues did not arise.As a consequence, they were adept at lumped parameter circuits and often notcomfortable with circuits where waves travel in space. However, in order todesign radio frequency (RF) communications integrated circuits (IC) in thegigahertz range, one must deal with transmission lines at chip interfaces andwhere interconnections on chip are far apart. Also, impedance matching isaddressed, which is a topic that arises most often in microwave circuits. In mycareer, there has been a gap in comprehension between analog low-frequencydesigners and microwave designers. Often, similar issues were dealt with in twodifferent languages. Although this book is more firmly based in lumped-elementanalog circuit design, it is nice to see that microwave knowledge is brought inwhere necessary.Too many analog circuit books in the past have concentrated first on thecircuit side rather than on basic theory behind their application in communications.The circuits usually used have evolved through experience, without asatisfying intellectual theme in describing them. Why a given circuit works bestcan be subtle, and often these circuits are chosen only through experience. Forthis reason, I am happy that the book begins first with topics that require anintellectual approach—noise, linearity and filtering, and technology issues. Iam particularly happy with how linearity is introduced (power series). In therest of the book it is then shown, with specific circuits and numerical examples,how linearity and noise issues arise.
上传时间： 2014-12-23
上传用户：han_zh
Finite state machines are widely used in digital circuit designs. Generally, when designing a state machine using an HDL, the synthesis tools will optimize away all states that cannot be reached and generate a highly optimized circuit. Sometimes, however, the optimization is not acceptable. For example, if the circuit powers up in an invalid state, or the circuit is in an extreme working environment and a glitch sends it into an undesired state, the circuit may never get back to its normal operating condition.
标签： Creating Machines Mentor State
上传时间： 2013-10-08
上传用户：wangzhen1990
介绍高速电路的设计
标签： High-speed Digital Design 高速数字
上传时间： 2013-10-16
上传用户：yt1993410
1.2MHz 2A Synchronous Step-Down converter
上传时间： 2013-11-01
上传用户：qingzhuhu
返驰式(Flyback) 电源供应器是交换式电源设计供应器(Switch Power Supply，SPS)的一种，为工业界常用之电路架构，其特点如下表所示，图一所示为返驰式转换器(Flyback Converter)电路。 一般设计SPS需要一些保护来提高系统设备之稳定安全，尤其是输出过电压保护极为重要，这个输出过电压保护目的是防止电气设备上的元件之绝缘遭受过电压的破坏。一般过电压的测试方法是将回授Open让系统呈现段回路状况，导致一次侧能量无限制提供给二次测来达到输出过电压现象。
上传时间： 2013-11-06
上传用户：haoxiyizhong
Abstract: The DS1875 features a pulse-width modulation (PWM) controller that can be used to control aDC-DC converter. The DC-DC converter can then be used to generate the high bias voltages necessaryfor avalanche photodiodes (APDs). This application note describes the operation of a boost converterthat uses the DS1875. Discussion covers the selection of the inductor and switching frequency, and theselection of components that improve the efficiency of the converter. Test data are presented.
上传时间： 2013-10-26
上传用户：lyson
特点（FEATURES） 精确度0.03%满刻度（Accuracy 0.03%F.S.） 频率输入范围0.01Hz至80KHz（Input range from 0.01 Hz to 80KHz） 16 BIT 隔离类比输出（16 bit DAC isolating analog output） 输入与输出1/输出2绝缘耐压 2仟伏特/1分钟（Dielectric strength 2KVac/1min.（input/output1/output2）） 宽范围交直流两用电源设计（Wide input range for auxiliary power） 尺寸小，稳定性高（Dimension small & High stability）
上传时间： 2013-10-21
上传用户：dljwq
特点(FEATURES) 精确度0.1%满刻度 (Accuracy 0.1%F.S.) 可作各式数学演算式功能如:A+B/A-B/AxB/A/B/A&B(Hi or Lo)/|A| (Math functioA+B/A-B/AxB/A/B/A&B(Hi&Lo)/|A|/etc.....) 16 BIT 类比输出功能(16 bit DAC isolating analog output function) 输入/输出1/输出2绝缘耐压2仟伏特/1分钟(Dielectric strength 2KVac/1min. (input/output1/output2/power)) 宽范围交直流两用电源设计(Wide input range for auxiliary power) 尺寸小,稳定性高(Dimension small and High stability)
上传时间： 2013-11-24
上传用户：541657925
针对TI公司最新发布的TMS320C6678 DSP设计出一种实用有效的电源。采用统一的12 V电源供电，制作出满足电压幅值要求与时序要求的开关电源。该设计主要由各类电源转换电路组成，并通过使用Fusion Digital Power Designer软件对电源芯片进行编程。仿真结果表明，该电源工作稳定，各方面的参数均符合要求。
上传时间： 2013-10-12
上传用户：asdstation
Abstract: A resistive feedback network is often used to set the output voltage of a power supply. A mechanical potentiometer (pot)conveniently solves the problem of adjusting a power supply. For easier automatic calibration, a mechanical pot can be replaced witha digital pot. This application note presents a calibration solution that uses a digital pot, because digipots are smaller, do not movewith age or vibration, and can be recalibrated remotely. This proposed solution reduces the susceptibility of the system to thetolerance of the digital pot's end-to-end resistance, making the solution optimal fordesigners. This application note also explainssome of the equations required to calculate the resistor chain values and to use a digital pot in this way. A spreadsheet withstandard reisistor values is available for easy calculations.
上传时间： 2013-10-31
上传用户：caiguoqing
