MC52233 based data Acquisition schematic
标签: Acquisition schematic 52233 based
上传时间: 2014-01-24
上传用户:xaijhqx
MC52233 based data Acquisition schematic
标签: Acquisition schematic 52233 based
上传时间: 2017-06-07
上传用户:tuilp1a
The Open Radar Data Acquisition (ORDA) subsystem replaces the current WSR-88D Radar Data Acquisition subsystem with improved receiver and signal processing hardware and with improved user interface, signal processing and diagnostics software. This paper will discuss the input data from the digital receiver, the ORDA signal processing, and the data output from the ORDA hardware. Specifications of the ORDA digital receiver will be presented. The paper outlines the critical radar signal processing flow and provides analysis of new spectrum width computations and clutter filtering schemes used in the ORDA system. Where appropriate, ORDA performance enhancements, data quality improvements and reliability and maintenance improvements will be highlighted.
标签: Radar Data Acquisition Acquisiti
上传时间: 2017-08-25
上传用户:leixinzhuo
Multiuser multiple-input-multiple-output (MU- MIMO) systems are known to be hindered by dimensionality loss due to channel state information (CSI) Acquisition overhead. In this paper, we investigate user-scheduling in MU-MIMO systems on account of CSI Acquisition overhead, where a base station dynamically acquires user channels to avoid choking the system with CSI overhead.
标签: Acquisition Dynamic Channel
上传时间: 2020-05-27
上传用户:shancjb
The system of image Acquisition base on cpld and cis基于CPLD和接触式图像传感器的图像采集系统
上传时间: 2013-08-11
上传用户:mickey008
Abstract: IC switches and multiplexers are proliferating, thanks to near-continual progress in lowering the supply voltage,incorporating fault-protected inputs, clamping the output voltage, and reducing the switch resistances. The latest of these advancesis the inclusion of precision resistors to allow two-point calibration of gain and offset in precision data-Acquisition systems.
上传时间: 2013-11-12
上传用户:acwme
Abstract: Using a DAC and a microprocessor supervisor, the system safety can be improved in industrial controllers, programmablelogiccontrollers (PLC), and data-Acquisition systems. The analog output is set to zero-scale (or pin-programmable midscale) when amicroprocessor failure, optocoupler failure, or undervoltage condition occurs. A simple application is shown on how to implement thisfunction.
上传时间: 2013-10-17
上传用户:sjb555
A complete design for a data Acquisition card for the IBM PC is detailed in this application note. Additionally, C language code is provided to allow sampling of data at speed of more than 20kHz. The speed limitation is strictly based on the execution speed of the "C" data Acquisition loop. A "Turbo" XT can acquire data at speeds greater than 20kHz. Machines with 80286 and 80386 processors can go faster than 20kHz. The computer that was used as a test bed in this application was an XT running at 4.77MHz and therefore all system timing and Acquisition time measurements are based on a 4.77MHz clock speed.
上传时间: 2013-10-29
上传用户:BOBOniu
Low power operation of electronic apparatus has becomeincreasingly desirable. Medical, remote data Acquisition,power monitoring and other applications are good candidatesfor battery driven, low power operation. Micropoweranalog circuits for transducer-based signal conditioningpresent a special class of problems. Although micropowerICs are available, the interconnection of these devices toform a functioning micropower circuit requires care. (SeeBox Sections, “Some Guidelines for Micropower Designand an Example” and “Parasitic Effects of Test Equipmenton Micropower Circuits.”) In particular, trade-offs betweensignal levels and power dissipation become painful whenperformance in the 10-bit to 12-bit area is desirable.
上传时间: 2013-10-22
上传用户:rocketrevenge
Portable, battery-powered operation of electronic apparatushas become increasingly desirable. Medical, remotedata Acquisition, power monitoring and other applicationsare good candidates for battery operation. In some circumstances,due to space, power or reliability considerations,it is preferable to operate the circuitry from a single 1.5Vcell. Unfortunately, a 1.5V supply eliminates almost alllinear ICs as design candidates. In fact, the LM10 opamp-reference and the LT®1017/LT1018 comparators arethe only IC gain blocks fully specifi ed for 1.5V operation.Further complications are presented by the 600mV dropof silicon transistors and diodes. This limitation consumesa substantial portion of available supply range, makingcircuit design diffi cult. Additionally, any circuit designedfor 1.5V operation must function at end-of-life batteryvoltage, typically 1.3V. (See Box Section, “Componentsfor 1.5V Operation.”)
标签: Circuitry Operation Single 1017
上传时间: 2013-12-20
上传用户:Wwill