The CAT9534 is an 8-bit parallel input/output portexpANder for I²C ANd SMBus compatible applications.These I/O expANders provide a simple solution inapplications where additional I/Os are needed: sensors,power switches, LEDs, pushbuttons, ANd fans.The CAT9534 consists of an input port register, anoutput port register, a configuration register, a polarityinversion register ANd an I²C/SMBus-compatible serialinterface.
上传时间： 2013-11-09
上传用户：liulinshan2010
All inputs of the C16x family have Schmitt-Trigger input characteristics. These Schmitt-Triggers are intended to always provide proper internal low ANd high levels, even if anundefined voltage level (between TTL-VIL ANd TTL-VIH) is externally applied to the pin.The hysteresis of these inputs, however, is very small, ANd can not be properly used in anapplication to suppress signal noise, ANd to shape slow rising/falling input transitions.Thus, it must be taken care that rising/falling input signals pass the undefined area of theTTL-specification between VIL ANd VIH with a sufficient rise/fall time, as generally usualANd specified for TTL components (e.g. 74LS series: gates 1V/us, clock inputs 20V/us).The effect of the implemented Schmitt-Trigger is that even if the input signal remains inthe undefined area, well defined low/high levels are generated internally. Note that allinput signals are evaluated at specific sample points (depending on the input ANd theperipheral function connected to it), at that signal transitions are detected if twoconsecutive samples show different levels. Thus, only the current level of an input signalat these sample points is relevant, that means, the necessary rise/fall times of the inputsignal is only dependant on the sample rate, that is the distance in time between twoconsecutive evaluation time points. If an input signal, for instance, is sampled throughsoftware every 10us, it is irrelevant, which input level would be seen between thesamples. Thus, it would be allowable for the signal to take 10us to pass through theundefined area. Due to the sample rate of 10us, it is assured that only one sample canoccur while the signal is within the undefined area, ANd no incorrect transition will bedetected. For inputs which are connected to a peripheral function, e.g. capture inputs, thesample rate is determined by the clock cycle of the peripheral unit. In the case of theCAPCOM unit this means a sample rate of 400ns @ 20MHz CPU clock. This requiresinput signals to pass through the undefined area within these 400ns in order to avoidmultiple capture events.For input signals, which do not provide the required rise/fall times, external circuitry mustbe used to shape the signal transitions.In the attached diagram, the effect of the sample rate is shown. The numbers 1 to 5 in thediagram represent possible sample points. Waveform a) shows the result if the inputsignal transition time through the undefined TTL-level area is less than the time distancebetween the sample points (sampling at 1, 2, 3, ANd 4). Waveform b) can be the result ifthe sampling is performed more than once within the undefined area (sampling at 1, 2, 5,3, ANd 4).Sample points:1. Evaluation of the signal clearly results in a low level2. Either a low or a high level can be sampled here. If low is sampled, no transition willbe detected. If the sample results in a high level, a transition is detected, ANd anappropriate action (e.g. capture) might take place.3. Evaluation here clearly results in a high level. If the previous sample 2) had alreadydetected a high, there is no change. If the previous sample 2) showed a low, atransition from low to high is detected now.
上传时间： 2013-10-23
上传用户：copu
Abstract: This application note explains the hardware of different types of 1-Wire® interfaces ANd software examples adapted to this hardware with a focus on serial ports. Depending on the types of iButtons required for a project ANd the type of computer to be used, the most economical interface is easily found. The hardware examples shown are basically two different types: 5V general interface ANd 12V RS-232 interface. Within the 5V group a common printed circuit board could be used for all circuits described. The variations can be achieved by different populations of components. The same principal is used for the 12V RS-232 interface. The population determines if it is a Read all or a Read/Write all type of interface. There are other possible circuit implementations to create a 1-Wire interface. The circuits described in this application note cover many different configurations. For a custom application, one of the described options can be adapted to meet individual needs.
标签： iButtons Reading Writing ANd
上传时间： 2013-10-29
上传用户：long14578
pwm research ANd implementation on mcs-51
标签： implementatio research pwm ANd
上传时间： 2013-11-23
上传用户：a155166
The Linux Programming Interface - A Linux ANd UNIX System
标签： Programming Linux Interface HANdbook
上传时间： 2013-11-10
上传用户：asdstation
The main objective of this book is to present all the relevant informationrequired for RF ANd micro-wave power amplifier design includingwell-known ANd novel theoretical approaches ANd practical design techniquesas well as to suggest optimum design approaches effectively combininganalytical calculations ANd computer-aided design. This bookcan also be very useful for lecturing to promote the analytical way ofthinking with practical verification by making a bridge between theoryANd practice of RF ANd microwave engineering. As it often happens, anew result is the well-forgotten old one. Therefore, the demonstrationof not only new results based on new technologies or circuit schematicsis given, but some sufficiently old ideas or approaches are also introduced,that could be very useful in modern practice or could contributeto appearance of new ideas or schematic techniques.
标签： Amplifier Microwave Design Power
上传时间： 2013-12-22
上传用户：vodssv
RF circuit design theory ANd application(射频电路设计)
标签： application circuit design theory
上传时间： 2014-12-30
上传用户：aeiouetla
通信物理层仿真，有代码，包括BPSK,QPSK,MSK,GMSK,扩频等等，Artech.House_2002_Simulation.ANd.Software.Radio.for.Mobile.Communications。
标签： Communications Simulation Software Artech
上传时间： 2013-11-01
上传用户：jhksyghr
Abstract: Using a wafer-level package (WLP) can reduce the overall size ANd cost of your solution.However when using a WLP IC, the printed circuit board (PCB) layout can become more complex ANd, ifnot carefully planned, result in an unreliable design. This article presents some PCB designconsiderations ANd general recommendations for choosing a 0.4mm- or 0.5mm-pitch WLP for yourapplication.
标签： Considerations Guidelines ANd Design
上传时间： 2013-11-09
上传用户：ls530720646
PADS-PowerLogic ANd PowerPcb实用教程
标签： PADS-PowerLogic PowerPcb ANd 实用教程
上传时间： 2014-01-24
上传用户：qiaoyue
