The Original USB 2.0 specification released on April 27, 2000 Errata to the USB 2.0 specification as of December 7, 2000 Mini-B connector Engineering Change Notice to the USB 2.0 specification. Pull-up/pull-down Resistors Engineering Change Notice to the USB 2.0 specification. Errata to the USB 2.0 specification as of May 28, 2002 Interface Association Descriptor Engineering Change Notice to the USB 2.0 specification. Rounded Chamfer Engineering Change Notice to the USB 2.0 specification as of October 8, 2003 Unicode Engineering Change Notice to the USB 2.0 specification as of February 21, 2005 Inter-Chip USB Supplement Revision 1.0 as of March 13, 2006 Revision 1.3 of the USB On-The-Go Supplement as of December 5, 2006 Revision 1.01 of the Micro-USB Cables and Connectors Specification as of April 4, 2007 USB 2.0 Link Power Management Addendum Engineering Change Notice to the USB 2.0 specification as of July 16, 2007.
标签： specification 2.0 USB Original
上传时间： 2013-12-31
上传用户：familiarsmile
How to use USB without knowing USB
上传时间： 2014-01-21
上传用户：lhc9102
cpress usb 芯片Vender 处理固件。 The purpose of this software is to demonstrate how to implement vendor specific commands. The following vendor specific commands are implemented: A0 Firmware Upload/Download A2 EEProm Load A3 External Ram Load A4 Set I2C Addr A5 Get IIC Type (1 Byte or 2 Byte EEPROM) A6 Get Chip Rev A8 Renumerate
标签： demonstrate implement software purpose
上传时间： 2016-01-14
上传用户：stvnash
S3C2410的驱动,包括USB UART,需在PB环境编译
上传时间： 2013-12-21
上传用户：yyyyyyyyyy
NAND Flash Boot Please select function : 0 : USB download file（通过USB下载文件） 1 : Uart download file（通过串口下载文件） 2 : Write Nand flash with download file（将下载的文件烧写到NandFlash） 3 : Load Pragram from Nand flash and run（从NandFlash装载文件并运行） 4 : Erase Nand flash regions（擦除NandFlash区域） 5 : Write NOR flash with download file（将下载的文件烧写到NorFlash） 6 : Set boot params（设置Linux启动相关参数） 7 : Set AutoBoot parameter,1:linux 2:wince(设置WINCE自启动）
标签： download USB function Please
上传时间： 2016-02-15
上传用户：s363994250
Ti TMS320C6713 DSK的测试程序,全部代码都有.包括BOOT,CODEC,EDMA,EEPROM,FLASH,GPIO,SDRAM,Timer,UART,USB等
上传时间： 2014-09-10
上传用户：851197153
verilog code which receive from uart RX and then output to lcd text display.
标签： verilog receive display output
上传时间： 2016-03-07
上传用户：songrui
// This program demonstrates how to configure the C8051F060 to write to and read // from the UART interface. The program reads a word using the UART0 interrupts // and outputs that word to the screen, with all characters in uppercase
标签： demonstrates C8051F060 configure the
上传时间： 2013-12-23
上传用户：hopy
學習usb的必讀書籍.. USB Complete: Everything You Need to Develop USB Peripherals, Third Edition by Jan Axelson
标签： Peripherals Everything USB Complete
上传时间： 2014-01-03
上传用户：671145514
AVR单片机USB口转换为UART异步串行口的详细程序，非常好用
上传时间： 2016-04-18
上传用户：脚趾头
