Designing read/write device (RWD) units for industrial RF-Identification applications is strongly facilitated by the NXP Semiconductors HITAG Reader Chip HTRC110. All needed function blocks, like the antenna driver, modulator demodulator and antenna diagnosis unit, are integrated in the HTRC110. Therefore only a minimum number of additional passive components are required for a complete RWD. This Application Note describes how to design an industrial RF-Identification system with the HTRC110. The major focus is dimensioning of the antenna, all other external components including clock and power supply, as well as the demodulation principle and its implementatio
上传时间： 2013-10-22
上传用户：zhengjian
为解决输油管道温度压力参数实时监测的问题，设计了以C8051F930单片机作为控制核心的超低功耗输油管道温度压力远程监测系统。现场仪表使用高精度电桥采集数据，通过433 MHz短距离无线通信网络与远程终端RTU进行通信，RTU通过GPRS网络与PC上位机进行远程数据传输，在上位机中实现数据存储和图形化界面显示，从而实现输油管道温度压力参数的实时监测和异常报警。经实验证明，该系统的12位数据采集精度满足设计要求，漏码率小于1%，正常工作时间超过5个月，能实时有效地监测输油管道的温度压力参数，节省大量人工成本，有效预防管道参数异常造成的经济损失和环境污染。 Abstract: In order to solve the problems on real-time monitoring of pipeline temperature and pressure parameters， the ultra-low power remote pipeline temperature and pressure monitoring system was designed by using the single chip processor C8051F930 as the control core. The high-precision electric bridge was used in field instruments for data collection， the 433MHz short-range wireless communication network was used to make communication between field instrument and RTU， the GPRS was used by the RTU to transmit data to the PC host computer， and the data was stored and displayed in the PC host computer， so the real-time monitoring and exception alerts of pipeline temperature and pressure parameters were achieved. The experiment proves that the system of which error rate is less than 1% over five months working with the 12-bit data acquisition accuracy can effectively monitor the pipeline temperature and pressure parameters in real time， it saves a lot of labor costs and effectively prevents environmental pollution and economic losses caused by abnormal channel parameters.
上传时间： 2013-11-07
上传用户：cuibaigao
为了在工业生产及过程控制中准确测量温度，设计了一种基于低功耗MSP430单片机的数字温度计。整个系统通过单片机MSP430F1121A控制DS18B20读取温度，采用数码管显示，温度传感器DS18B20与单片机之间通过串口进行数据传输。MSP430系列单片机具有超低功耗，且外围的整合性高，DS18B20只需一个端口即可实现数据通信，连接方便。通过多次实验证明，该系统的测试结果与实际环境温度一致，除了具有接口电路简单、测量精度高、误差小、可靠性高等特点外，其低成本、低功耗的特点使其拥有更广阔的应用前景。 Abstract: In order to obtain accurate measuring temperature in industrial production and process control， a digital thermometer based on MSP430 MCU is designed. The system uses MSP430F1121A MCU to control DS18B20， and gets the temperature data， which is displayed on the LED. The temperature sensor DS18B20 and MCU transmit data through serial communication. MSP430 series has ultra-low power and high integration， DS18B20 only needs one port to achieve data communication. Through many experimental results prove， this system is consistent with actual environment temperature. The system has characteristics of interface circuit simple， high measuring accuracy， minor error， high reliability， besides， the characteristics of low cost and low power make it having vaster application prospect.
上传时间： 2013-10-16
上传用户：wettetw
The MSP-FET430U14 is a powerful flash emulation tool to quickly begin application development on the MSP430 MCU. It includes USB debugging interface used to program and debug the MSP430 in-system through the JTAG interface or the pin saving Spy Bi-Wire (2-wire JTAG) protocol. The flash memory can be erased and programmed in seconds with only a few keystrokes, and since the MSP430 flash is ultra-low power, no external power supply is required. The debugging tool interfaces the MSP430 to the included integrated software environment and includes code to start your design immediately. The MSP-FET430UIF development tools supports development with all MSP430 flash devices
上传时间： 2013-10-28
上传用户：13691535575
Atmel AVR 单片机上网方案 The AVR Embedded Internet Toolkit is the fastest way to connect anyembedded design to the Internet. It includes an ATmega AVR microcontroller,dedicated hardware, and all required software protocols forconnecting to the Internet. The AVR Embedded Internet Toolkit is thefastest choice for getting started with embedded Internet and for developinga complete embedded application connected to the Internet.
上传时间： 2013-11-06
上传用户：xjz632
Features• Complete DTMF Receiver• Low power consumption• Internal gain setting amplifier• Adjustable guard time• Central office quality• Power-down mode• Inhibit mode• Backward compatible withMT8870C/MT8870C-1Applications• Receiver system for British Telecom (BT) orCEPT Spec (MT8870D-1)• Paging systems• Repeater systems/mobile radio• Credit card systems• Remote control• Personal computers• Telephone answering machine
上传时间： 2013-11-20
上传用户：mpquest
Using the XGATE for Manchester DecodingTable of Contents 1 Introduction 1.1 XGATE Module in S12X 2 Decoding Algorithm 3 Software Implementation 3.1 Frame Scheme 3.2 Operating Modes and Demo 3.3 Files Summary 3.4 Complete Mode Flowchart 4 Manchester Encoder 4.1 Devices Used 5 Conclusion Appendix A Noise Elements During RF Transmissions in the Manchester Decoding ImplementationA.1 Types of Noise A.2 Effects of Noise A.3 Workaround for Noise Effects
标签： Manchester XGATE 译码
上传时间： 2013-10-15
上传用户：wqq123456
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their productsor to discontinue any product or service without notice, and advise customers to obtain the latestversion of relevant information to verify, before placing orders, that information being relied onis current and complete. All products are sold subject to the terms and conditions of sale suppliedat the time of order acknowledgement, including those pertaining to warranty, patentinfringement, and limitation of liability.
标签： Assembly Language C6000 320C
上传时间： 2013-11-12
上传用户：chens000
基于PIC单片机的低功耗读卡器硬件设计:本文提出了一个完整的基于串口的智能读卡器子系统设计方案并将其实现。读卡器的设计突出了小型化的要求，全部器件使用贴片封装。为了减小读卡器的体积，设计中还使用了串口窃电的技术，使用串口信号线直接给读卡器供电。为此，读卡器使用了省电的设计，采用了省电的集成电路，并大胆简化了许多传统的设计电路。关键字： 读卡器， 单片机， 串口窃电 Abstract： This paper aims to put forward a complete design of Smart IC card reader based onSerial Port and propose the way of realizing it for the purpose of Network Security. SMD isadopted to make Smart IC reader smaller in this design. To reduce the volume of Smart ICreader， Serial Port powered technology is employed to get power from the signal line of Serial Port. For this reason， low-power consumption components are adopted in the design and some traditional designs are simplified to reduce the power consumption.Keywords： Card Reader； Single-chip Computer； Serial Port Powered IC 卡系统保存了加密算法所需要的工作密钥，供加密算法对网络上传输的数据加密使用，是整个系统网络安全的核心。在IC 卡子系统中，读卡器是一个重要的部分。它起着管理IC卡、在IC 卡和PC或网络计算机间传递数据的重要作用。本文以一片PIC单片机为核心完成了基于RS232 串口的读卡器的硬件设计。
上传时间： 2014-04-14
上传用户：wanghui2438
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
标签： Demonstration 3200 USB for
上传时间： 2014-02-27
上传用户：zhangzhenyu
