In general, a Hot Swap controller provides two importantfunctions to boards that can be plugged and unpluggedfrom a live backplane:
上传时间： 2013-10-23
上传用户：行者Xin
The LTM4600 DC/DC μModule regulator is a complete highpower density stepdown regulator for 10A continuous (14Apeak) loads. The device has two voltage options: 20VINmaximum for the LTM4600EV and 28VIN maximum for theLTM4600HVEV each housed in a small 15mm ¥ 15mm ¥2.8mm LGA surface mount package.
上传时间： 2013-10-10
上传用户：adada
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
Demonstration circuit 1562A is an engineering toolto design and evaluate the LTC699X-X family ofTimerBlox circuits. The center section of the boardcontains a pre-configured TimerBlox function.DC1562A comes in twelve timing function variationsas outlined in Table 1.Surrounding the center board is a ”playground”prototyping area. The prototyping area has padsfor Dip-8, S8, MS8, or S6 packages with breadboarding connections to each pin and two convenientpower buses and ground bus surrounding theentire area. This area is for conditioning signals tocontrol the timer function and for adding loads controlled in time.
上传时间： 2013-10-18
上传用户：如果你也听说
The P89LPC912/913/914 are single-chip microcontrollers in low-cost 14-pin packages, based on a high performance processor architecture that executes instructions in two to four clocks, six times the rate of standard 80C51 devices. Many system level functions have been incorporated into the P89LPC912/913/914 in order to reduce component count, board space, and system cost.
上传时间： 2013-10-12
上传用户：司令部正军级
HIGH SPEED 8051 μC CORE - Pipe-lined Instruction Architecture; Executes 70% of Instructions in 1 or 2 System Clocks - Up to 25MIPS Throughput with 25MHz System Clock - 22 Vectored Interrupt Sources MEMORY - 4352 Bytes Internal Data RAM (256 + 4k) - 64k Bytes In-System Programmable FLASH Program Memory - External Parallel Data Memory Interface – up to 5Mbytes/sec DIGITAL PERIPHERALS - 64 Port I/O; All are 5V tolerant - Hardware SMBusTM (I2CTM Compatible), SPITM, and Two UART Serial Ports Available Concurrently - Programmable 16-bit Counter/Timer Array with 5 Capture/Compare Modules - 5 General Purpose 16-bit Counter/Timers - Dedicated Watch-Dog Timer; Bi-directional Reset CLOCK SOURCES - Internal Programmable Oscillator: 2-to-16MHz - External Oscillator: Crystal, RC, C, or Clock - Real-Time Clock Mode using Timer 3 or PCA SUPPLY VOLTAGE ........................ 2.7V to 3.6V - Typical Operating Current: 10mA @ 25MHz - Multiple Power Saving Sleep and Shutdown Modes 100-Pin TQFP (64-Pin Version Available) Temperature Range: –40°C to +85°C
标签： C8051F020
上传时间： 2013-10-12
上传用户：lalalal
为了使音频信号分析仪小巧可靠，成本低廉，设计了以2片MSP430F1611单片机为核心的系统。该系统将音频信号送入八阶巴特沃兹低通滤波器，对信号进行限幅放大、衰减、电平位移、缓冲，并利用一单片机负责对前级处理后的模拟信号进行采样，将采集得到的音频信号进行4 096点基2的FFT计算，并对信号加窗函数提高分辨率，另一单片机负责对信号的分析及控制显示设备。此设计精确的测量了音频信号的功率谱、周期性、失真度指标，达到较高的频率分辨率，并能将测量结果通过红外遥控器显示在液晶屏上。 Abstract: o make the audio signal analyzer cheaper， smaller and more reliable， this system sends the audio signal to the eight-order butterworth filter， and then amplifies， attenuates， buffers it in a limiting range， transfers the voltage level of the signal before utilizing two MSP430F1611 MCU to realize the audio analysis. One is charged for sampling and dealing with the processed audio signal collected by the 4096 point radix-2 FFT calculation and imposes the window function to improve the frequency resolution. The other one controls the display and realizes the spectrum， periodicity， power distortion analysis in high resolution which is displayed in the LCD screen through the infrared remote control.
上传时间： 2013-12-11
上传用户：jasonheung
为解决当前计算机串行通讯接口只有USB，难以满足旧型号设备或某些单片机要求RS232通讯的问题，设计出两款RS232/USB电路。采用CH341A与MAX223集成电路芯片构建标准9线RS232/USB通用接口转换器，无需编程。采用CH341A与PIC16F877A构建单片机与计算机之间的USB通讯电路，软件遵循RS232通讯协议，硬件进行电平转换。实际使用表明，这两款产品与计算机端Windows 操作系统下的串口应用程序完全兼容，且通讯过程中无握手失败现象。 Abstract: To solve the problem that current computer serial communication only with USB interface can not satisfy with the old type equipments or MCU to communicate with RS232， two kinds of RS232/USB circuit were designed.CH341A and MAX223 integrated circuit chips were used to create a standard 9-line RS232/USB universal interface convertor without programme. CH341A and PIC16F877A chips were adopted to build the USB communication circuit between computers and MCU. The software follows RS232 communication protocol， and the hardware converts electrical levels. Actual practices indicate that the two manufactures are compatible with serial application program of Windows operation system completely，and get avoid of handshake lost.
上传时间： 2013-11-03
上传用户：siying
以太网和CAN总线应用广泛，但由于其通信协议不同，两种总线器件间无法进行数据通信，因此，设计了基于CP2200与C8051F040的以太网总线与CAN总线接口转换电路，并给出部分相关硬件电路与软件设计分析。在保证数据完整和协议可靠的前提下，通过握手协议和简化的以太网协议，不仅实现了以太网数据与CAN数据的转发，同时还顺利的解决了以太网的高速性与CAN的低速率冲突，以及两者数据包之间的大小不同的矛盾。 Abstract: In the development of actual application， Ethernet and CAN bus are used very extensively. Owing to its various communication protocols， the communicating between two kinds of bus device can’t be carried out. Therefore， in order to solve this problem， the Ethernet-CAN bus interface circuit based on CP2200 and C8051F040 was designed in this paper， and part of the related hardware circuit and software design analysis were given. On the condition of data’s integrity and protocols’reliability， through the handshaking protocols and the simplified the Ethernet protocol， not only the data switching between CAN and Ethernet was realized， but also the differ in velocity and packet size was solved.
上传时间： 2013-10-15
上传用户：Ants
提出一种基于凌阳单片机的步进电机加减速的控制方法。采用凌阳科技推出的16位结构工控单片机SPMC75F2413A为控制器，由Allegro公司生产的两相步进电机专用驱动器件SLA7042M构成步进电机的驱动电路，在传统的3段直线加减速控制算法基础上增加至7段S形曲线加减速过程，控制步进电机的启动和停止。实验结果表明，该控制方法克服了直线加减速中不连续、易造成系统冲击的问题，整个系统实现柔性控制，电机启动、停止连续性能提高30%。 Abstract: The method of controlled stepping motor is referred based on SPMC75F2413A MCU， which adopts the 16 knots SPMC75F2413A MCU as the controller. The special-purpose actuation chip SLA7042M of two stepping motor produced by Allegro Corporation constituted to actuation electric circuit. The purpose of increasing to seven section of S shape curve based on the traditional three sections of straight line is to control the start and stop process of stepping motor. The experimental results show that the control method solves easy to pull-out and overshot problems. The overall system realizes flexible control， and the performance of motor start or stop continuity is increased 30%
上传时间： 2013-12-08
上传用户：jiangfire
