高的工作电压高达100V N双N沟道MOSFET同步驱动 The D810DCDC is a synchronous step-down switching regulator controller that can directly step-down voltages from up to 100V, making it ideal for telecom and automotive applications. The D810DCDC uses a constant on-time valley current control architecture to deliver very low duty cycles with accurate cycle-by-cycle current limit, without requiring a sense resistor. A precise internal reference provides 0.5% DC accuracy. A high bandwidth (25MHz) error amplifi er provides very fast line and load transient response. Large 1Ω gate drivers allow the D810DCDC to drive multiple MOSFETs for higher current applications. The operating frequency is selected by an external resistor and is compensated for variations in VIN and can also be synchronized to an external clock for switching-noise sensitive applications. Integrated bias control generates gate drive power from the input supply during start-up and when an output shortcircuit occurs, with the addition of a small external SOT23 MOSFET. When in regulation, power is derived from the output for higher effi ciency.
上传时间： 2013-10-24
上传用户：wd450412225
The PCA9541 is a 2-to-1 I2C-bus master selector designed for high reliability dual masterI2C-bus applications where system operation is required, even when one master fails orthe controller card is removed for maintenance. The two masters (for example, primaryand back-up) are located on separate I2C-buses that connect to the same downstreamI2C-bus slave devices. I2C-bus commands are sent by either I2C-bus master and are usedto select one master at a time. Either master at any time can gain control of the slavedevices if the other master is disabled or removed from the system. The failed master isisolated from the system and will not affect communication between the on-line masterand the slave devices on the downstream I2C-bus.
上传时间： 2013-10-09
上传用户：3294322651
The MAX3243E device consists of three line drivers, five line receivers, and a dual charge-pump circuit with±15-kV ESD (HBM and IEC61000-4-2, Air-Gap Discharge) and ±8-kV ESD (IEC61000-4-2, Contact Discharge)protection on serial-port connection pins. The device meets the requirements of TIA/EIA-232-F and provides theelectrical interface between an asynchronous communication controller and the serial-port connector. Thiscombination of drivers and receivers matches that needed for the typical serial port used in an IBM PC/AT, orcompatible. The charge pump and four small external capacitors allow operation from a single 3-V to 5.5-Vsupply. In addition, the device includes an always-active noninverting output (ROUT2B), which allowsapplications using the ring indicator to transmit data while the device is powered down. The device operates atdata signaling rates up to 250 kbit/s and a maximum of 30-V/ms driver output slew rate.
标签： MULTICHANNEL 5.5 TO RS
上传时间： 2013-10-19
上传用户：ddddddd
Internal Interrupts are used to respond to asynchronous requests from a certain part of themicrocontroller that needs to be serviced. Each peripheral in the TriCore as well as theBus Control Unit, the Debug Unit, the Peripheral Control Processor (PCP) and the CPUitself can generate an Interrupt Request.So what is an external Interrupt?An external Interrupt is something alike as the internal Interrupt. The difference is that anexternal Interrupt request is caused by an external event. Normally this would be a pulseon Port0 or Port1, but it can be even a signal from the input buffer of the SSC, indicatingthat a service is requested.The User’s Manual does not explain this aspect in detail so this ApNote will explain themost common form of an external Interrupt request. This ApNote will show that there is aneasy way to react on a pulse on Port0 or Port1 and to create with this impulse an InterruptService Request. Later in the second part of the document, you can find hints on how todebounce impulses to enable the use of a simple switch as the input device.Note: You will find additional information on how to setup the Interrupt System in theApNote “First steps through the TriCore Interrupt System” (AP3222xx)1. It would gobeyond the scope of this document to explain this here, but you will find selfexplanatoryexamples later on.
上传时间： 2013-10-27
上传用户：zhangyigenius
I have written this article to capture a Windows image into a bitmap file that will support all PaintBrush tools and Thumbnail Views of Windows Explorer. I have found many programmers suffering from this problem, including me, until I wrote this article. 捕获一个窗口图像并存入一个支持MS画笔的位图文件中 我写的这篇文章介绍了捕获一个窗口图像并存入一个支持所有画笔和Windows Explorer的位图文件中。 我发现许多程序员因这个问题而烦恼,包括我在内,直到我写了这篇文章。 来源: http://www.codeguru.com/bitmap/WndToBmpFile.html
标签： article Windows capture written
上传时间： 2015-01-10
上传用户：hzy5825468
An easy, yet highly-configurable iptables-based firewall solution designed for everybody from home users to network admins. Functionality for IPv6, tunneling, IPSec, and advanced routing is planned.
标签： highly-configurable iptables-based everybody designed
上传时间： 2014-10-11
上传用户：huyiming139
WHAT MIME64 IS: MIME64 is an encoding described in RFC1341 as MIME base64.Its purpose is to encode binary files into ASCII so that they may be passedthrough e-mail gates. In this regard, MIME64 is similar to UUENCODE.Although most binaries these days are transmitted using UUENCODE, Ihave seen a few using MIME64, and I have had requests from friends thatI decode MIME64 files that have fallen into their hands. As long assome MIME64 continues to exist, a package such as this one is usefulto have.
标签： MIME described 64 encoding
上传时间： 2013-12-17
上传用户：maizezhen
tty驱动 * This driver shows how to create a minimal tty driver. It does not rely on * any backing hardware, but creates a timer that emulates data being received * from some kind of hardware.
标签： driver tty backing minimal
上传时间： 2013-12-04
上传用户：金宜
This program demonstrates how to do disconnected briefcase applications with ADO. When the Connected checkbox is unchecked the application is switched into offline mode. If the application is exited at that point then the data is persisted to a file on disk (along with any edits to the data). When the application is restarted it will load the persisted data if present, otherwise it will fetch the data from the database.
标签： demonstrates applications disconnected Connected
上传时间： 2015-03-24
上传用户：xcy122677
Invoke JavaProg.main() from a win32 program: . compile Main.java . compile VC project . set include path for jni.h, which is under java_Home\include . set linking path for jvm.lib, which is under java_Home\lib\jvm.lib . copy Main.class and Main$1.class to the working dir of the VC project (or the same dir with the output executable App.exe) . run App.exe . set searching path for jvm.dll
标签： compile JavaProg include program
上传时间： 2014-11-16
上传用户：思琦琦
