The MAX9257/MAX9258 programmable serializer/deserializer (SerDes) devices transfer both video data and control signals over the same twisted-pair cable. However, control data can only be transmitted during the vertical blank time, which is indicated by the control-channel-enabled output (CCEN) signal. The electronic control unit (ECU) firmware designer needs to know how quickly to respond to the CCEN signal before it times out and how to calculate this duration. This application note describes how to calculate the duration of the CCEN for the MAX9257/MAX9258 SerDes chipset. The calculation is based on STO timeout, clock frequency, and UART bit timing. The CCEN duration is programmable and can be closed if not in use.
上传时间： 2014-01-24
上传用户：xingisme
The PCA9516 is a BiCMOS integrated circuit intended forapplication in I2C and SMBus systems.While retaining all the operating modes and features of the I2Csystem, it permits extension of the I2C-bus by buffering both the data(SDA) and the clock (SCL) lines, thus enabling five buses of 400 pF.The I2C-bus capacitance limit of 400 pF restricts the number ofdevices and bus length. Using the PCA9516 enables the systemdesigner to divide the bus into five segments off of a hub where anysegment to segment transition sees only one repeater delay.
上传时间： 2013-11-21
上传用户：q123321
The PCA9517 is a CMOS integrated circuit that provides level shifting between lowvoltage (down to 0.9 V) and higher voltage (2.7 V to 5.5 V) I2C-bus or SMBus applications.While retaining all the operating modes and features of the I2C-bus system during thelevel shifts, it also permits extension of the I2C-bus by providing bidirectional buffering forboth the data (SDA) and the clock (SCL) lines, thus enabling two buses of 400 pF. Usingthe PCA9517 enables the system designer to isolate two halves of a bus for both voltageand capacitance. The SDA and SCL pins are over voltage tolerant and arehigh-impedance when the PCA9517 is unpowered.
标签： translating Level 9517 PCA
上传时间： 2013-12-25
上传用户：wsf950131
altium designer实例教程
上传时间： 2013-11-17
上传用户：zhaiye
简单实用
上传时间： 2013-10-11
上传用户：吾学吾舞
友善之臂的QtEmbedded实例教程 第一章 LINUX 图形用户界面 GUI 介绍.....................................................................................1 1.1 常用 GUI 介绍...................................................................................................................1 1.2 关于 Qt...............................................................................................................................2 1.3 Qt/Embedded 简介.............................................................................................................4 1.4 Qtopia 介绍.........................................................................................................................4 第二章 QT的安装..........................................................................................................................6 2.1 Qt X11 的安装....................................................................................................................6 2.2 Qt/Embedded 安装..............................................................................................................9 2.3 Qtopia 编译.......................................................................................................................11 第三章 QT的编程........................................................................................................................12 实验一 “Hello word！ ”Qt初探............................................................................................12 实验二 创建一个窗口并添加按钮.......................................................................................17 实验三 对象间通信：Signal 和 Slot 机制........................................................................20 实验四 菜单和快捷键...........................................................................................................29 实验五 工具条和状态栏.......................................................................................................38 实验六 鼠标和键盘事件.......................................................................................................48 实验七 对话框.......................................................................................................................63 实验八 Qt 中的绘图..............................................................................................................75 实验九 Qt 中的多线程编程..................................................................................................85 实验十 Qt 中的网络编程......................................................................................................97 第四章 QT常用工具的介绍...................................................................................................... 111 4.1 Qt 设计器（Qt Designer）............................................................................................ 111 4.2 Tmake..............................................................................................................................113 4.3 Qvfb ................................................................................................................................114
标签： QtEmbedded 教程
上传时间： 2013-12-21
上传用户：laozhanshi111
随着FPGA技术的发展，FPGA设计已不再只是硬件电路的设计，而是包含处理器、外围组件和接口逻辑在内的完整数字系统，同时在处理器中编程完成嵌入式代码的FPGA“软”设计。与传统的主要基于硬件描述语言进行FPGA设计开发不同，本文在电路设计软件Altium Designer开发环境下，结合Xilinx公司的ISE设计软件，在Altium Designer的创新电子设计平台NanoBoard 3000上，设计实现了基于Altium Designer特有的系统级设计方法OpenBus系统的32位处理器控制LED的FPGA嵌入式设计。
上传时间： 2013-11-09
上传用户：亚亚娟娟123
Altium 公司认识到越来越需要把所有核心EDA 软件工具集中到一个集成软件包中，从而可以实现从设计概念直到生产的无缝集成。因此Altium 发布了专为Windows NT 平台构建的Protel98，这是首次将所有5 种核心EDA 工具集成于一体的产品，这5 种核心EDA 工具包括原理图输入、可编程逻辑器件(PLD)设计、仿真、板卡设计和自动布线。
上传时间： 2014-12-30
上传用户：pei5
With the Altera Nios II embedded processor, you as the system designercan accelerate time-critical software algorithms by adding custominstructions to the Nios II processor instruction set. Using custominstructions, you can reduce a complex sequence of standard instructionsto a single instruction implemented in hardware. You can use this featurefor a variety of applications, for example, to optimize software innerloops for digital signal processing (DSP), packet header processing, andcomputation-intensive applications. The Nios II configuration wizard,part of the Quartus® II software’s SOPC Builder, provides a graphicaluser interface (GUI) used to add up to 256 custom instructions to theNios II processor
上传时间： 2013-11-07
上传用户：swing
电力设备热点温度与电流在线监测预警系统工作在大型变压器旁，极易受电磁辐射干扰，针对该预警系统的子系统：无线传输部分进行了抗电磁干扰设计，采用Ansoft Designer软件仿真分析了PCB（Printed Circuit Board）中电磁波对PCB电磁兼容性产生的影响，根据其得出的PCB的电流图及近场分布图，分析PCB的电磁兼容性，针对结果中的电磁辐射过高区域进行了重新设计，经Ansoft Designer验证，重新设计后的PCB各项指数有所下降，电磁兼容性得到提高。
上传时间： 2013-11-11
上传用户：ggwz258
