The PCA9670 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9670 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-15
上传用户：stella2015
The PCA9547 is an octal bidirectional translating multiplexer controlled by the I2C-bus.The SCL/SDA upstream pair fans out to eight downstream pairs, or channels. Only oneSCx/SDx channel can be selected at a time, determined by the contents of theprogrammable control register. The device powers up with Channel 0 connected, allowingimmediate communication between the master and downstream devices on that channel.
上传时间： 2014-12-28
上传用户：270189020
The PCA9671 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plus(Fm+) family.The PCA9671 is a drop in upgrade for the PCF8575 providing higher I2C-bus speeds(1 MHz versus 400 kHz) so that the output can support PWM dimming of LEDs, higherI2C-bus drive (30 mA versus 3 mA) so that many more devices can be on the bus withoutthe need for bus buffers, higher total package sink capacity (400 mA versus 100 mA) thatsupports having all 25 mA LEDs on at the same time and more device addresses (64versus 8) to allow many more devices on the bus without address conflicts.
上传时间： 2013-10-12
上传用户：laomv123
The PCA9672 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9672 is a drop-in upgrade for the PCF8574 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-23
上传用户：jasonheung
The PCA9673 provides general purpose remote I/O expansion for most microcontrollerfamilies via the two-line bidirectional bus (I2C-bus) and is a part of the Fast-mode Plusfamily.The PCA9673 is a drop in upgrade for the PCF8575 providing higher Fast-mode Plus(Fm+) I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(400 mA versus 100 mA) that supports having all 25 mA LEDs on at the same time andmore device addresses (16 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-29
上传用户：wkchong
The PCA9674/74A is a drop-in upgrade for the PCF8574/74A providing higher Fast-modePlus I2C-bus speeds (1 MHz versus 400 kHz) so that the output can support PWMdimming of LEDs, higher I2C-bus drive (30 mA versus 3 mA) so that many more devicescan be on the bus without the need for bus buffers, higher total package sink capacity(200 mA versus 100 mA) that supports having all LEDs on at the same time and moredevice addresses (64 versus 8) are available to allow many more devices on the buswithout address conflicts.
上传时间： 2013-10-22
上传用户：wwwwwen5
The PCA9557 is a silicon CMOS circuit which provides parallel input/output expansion for SMBus and I2C-bus applications. The PCA9557 consists of an 8-bit input port register, 8-bit output port register, and an I2C-bus/SMBus interface. It has low current consumption and a high-impedance open-drain output pin, IO0. The system master can enable the PCA9557’s I/O as either input or output by writing to the configuration register. The system master can also invert the PCA9557 inputs by writing to the active HIGH polarity inversion register. Finally, the system master can reset the PCA9557 in the event of a time-out by asserting a LOW in the reset input. The power-on reset puts the registers in their default state and initializes the I2C-bus/SMBus state machine. The RESET pin causes the same reset/initialization to occur without de-powering the part.
上传时间： 2014-01-18
上传用户：bs2005
The Philips family of Multiplexers and Switches consists of bi-directional translating switches controlled via the I2C or SMBus to fan out an upstream SCL/SDA pair to 2, 4 or 8 downstream channels of SCx/SDx pairs. The Multiplexers allow only one downstream channel to be selected at a time, while the Switches allow any individual downstream channel or combination of downstream channels to be selected, depending on the content of the programmable control register. Once one or several channels have been selected, the device acts as a wire, allowing the master on the upstream channel to send commands to devices on all the active downstream channels, and devices on the active downstream channels to communicate with each other and the master. External pull-up resistors are used to pull each individual channel up to the desired voltage level. Combined interrupt output and hardware reset input are device options that are featured.
上传时间： 2013-10-11
上传用户：dianxin61
基于单DSP的VoIP模拟电话适配器研究与实现:提出和实现了一种新颖的基于单个通用数字信号处理器(DSP)的VoIP模拟电话适配器方案。DSP的I/O和存储资源非常有限，通常适于运算密集型应用，不适宜控制密集型应用[5]。该系统高效利用单DSP的I/O和片内外存储器资源，采用μC/OS-II嵌入式实时操作系统，支持SIP和TCP-UDP/IP协议，通过LAN或者宽带接入，使普通电话机成为Internet终端，实现IP电话。该系统软硬件结构紧凑高效，运行稳定，成本低，具有广阔的应用前景。关键词：模拟电话适配器；IP电话；数字信号处理器；μC/OS-II 【Abstract】This paper presents a VoIP ATA solution based on a single digital signal processor (DSP). DSPs are suitable for arithmetic-intensiveapplication and unsuitable for control-intensive application because of the limitation of I/O and memory resources. This solution is based on a 16-bitfixed-point DSP and μC/OS-II embedded real-time operating system. It makes good use of the limited resources, supports SIP and TCP-UDP/IPprotocol. It can connect the analog telephone to Internet and realize the VoIP application. This system has a great future for its high efficiency andlow cost.【Key words】Analog telephone adapter (ATA); Voice over Internet protocol (VoIP); Digital signal processor (DSP); μC/OS-II Research and Implementation of VoIPATA Based on Single DSP
上传时间： 2013-11-20
上传用户：Wwill
The μPSD32xx family, from ST, consists of Flash programmable system devices with a 8032 MicrocontrollerCore. Of these, the μPSD3234A and μPSD3254A are notable for having a complete implementationof the USB hardware directly on the chip, complying with the Universal Serial Bus Specification, Revision1.1.This application note describes a demonstration program that has been written for the DK3200 hardwaredemonstration kit (incorporating a μPSD3234A device). It gives the user an idea of how simple it is to workwith the device, using the HID class as a ready-made device driver for the USB connection.IN-APPLICATION-PROGRAMMING (IAP) AND IN-SYSTEM-PROGRAMMING (ISP)Since the μPSD contains two independent Flash memory arrays, the Micro Controller Unit (MCU) can executecode from one memory while erasing and programming the other. Product firmware updates in thefield can be reliably performed over any communication channel (such as CAN, Ethernet, UART, J1850)using this unique architecture. For In-Application-Programming (IAP), all code is updated through theMCU. The main advantage for the user is that the firmware can be updated remotely. The target applicationruns and takes care on its own program code and data memory.IAP is not the only method to program the firmware in μPSD devices. They can also be programmed usingIn-System-Programming (ISP). A IEEE1149.1-compliant JTAG interface is included on the μPSD. Withthis, the entire device can be rapidly programmed while soldered to the circuit board (Main Flash memory,Secondary Boot Flash memory, the PLD, and all configuration areas). This requires no MCU participation.The MCU is completely bypassed. So, the μPSD can be programmed or reprogrammed any time, anywhere, even when completely uncommitted.Both methods take place with the device in its normal hardware environment, soldered to a printed circuitboard. The IAP method cannot be used without previous use of ISP, because IAP utilizes a small amountof resident code to receive the service commands, and to perform the desired operations.
标签： Demonstration 3200 USB for
上传时间： 2014-02-27
上传用户：zhangzhenyu
