1 Noise enhanced binary hypothesis-testing in a new framework
标签: hypothesis-testing enhanced binary Noise
上传时间: 2016-06-02
上传用户:siguazgb
音频管理组件(Audio Management Unit,AMU)是先进客舱娱乐与服务系统(Advanced Cabin Entertainment Service System,ACESS)的组成部分,应用于飞机上音频资源的管理与控制。飞机运营对航空机载电子系统准确性、复杂性和安全性的高要求,使得其维修维护工作极大地依赖于自动测试设备(Automatic testing Equipment,ATE)。本课题来源于实际工程项目, FPGA技术具备多种优点,将其与民航测试设备结合研制一个用于检测AMU故障的自动测试系统,该系统将对AMU自动完成部件维修手册(Comvonent Maintenance Manual,CMM)所规定的全部功能、性能方面的综合测试。 本文首先概述音频管理组件、自动测试系统及其在民航领域的应用,并阐述了课题的背景、研究目标和相关技术要求;文章对可编程逻辑器件CPLD/FPGA的结构原理、硬件描述语言VHDL的特点以及MAXL+plusⅡ软件的设计流程进行了说明,重点阐述了基于FPGA的DDS信号发生器以及数据采集卡的设计实现、并着重阐述了ARINC429总线的传输规范,和基于FPGA的ARINC429总线接口的设计与实现。在ARINC429接口设计中采用自顶向下,多层次系统设计的方法,用VHDL语言进行描述。在发送器中利用了FPGA内部的分布式RAM创建异步FIFO,节约了FPGA的内部资源和提高了数据传输速度;在接收器中采用了提高抗干扰性的优化设计。测试结果表明基于FPGA的设计实现ARINC429总线数据通信的要求,使用方便,可靠性好,能够克服HS-3282芯片中的数据格式固定,使用不够灵活方便,价格昂贵的缺点。
上传时间: 2013-08-06
上传用户:gzming
磁芯电感器的谐波失真分析 摘 要:简述了改进铁氧体软磁材料比损耗系数和磁滞常数ηB,从而降低总谐波失真THD的历史过程,分析了诸多因数对谐波测量的影响,提出了磁心性能的调控方向。 关键词:比损耗系数, 磁滞常数ηB ,直流偏置特性DC-Bias,总谐波失真THD Analysis on THD of the fer rite co res u se d i n i nductancShi Yan Nanjing Finemag Technology Co. Ltd., Nanjing 210033 Abstract: Histrory of decreasing THD by improving the ratio loss coefficient and hysteresis constant of soft magnetic ferrite is briefly narrated. The effect of many factors which affect the harmonic wave testing is analysed. The way of improving the performance of ferrite cores is put forward. Key words: ratio loss coefficient,hysteresis constant,DC-Bias,THD 近年来,变压器生产厂家和软磁铁氧体生产厂家,在电感器和变压器产品的总谐波失真指标控制上,进行了深入的探讨和广泛的合作,逐步弄清了一些似是而非的问题。从工艺技术上采取了不少有效措施,促进了质量问题的迅速解决。本文将就此热门话题作一些粗浅探讨。 一、 历史回顾 总谐波失真(Total harmonic distortion) ,简称THD,并不是什么新的概念,早在几十年前的载波通信技术中就已有严格要求<1>。1978年邮电部公布的标准YD/Z17-78“载波用铁氧体罐形磁心”中,规定了高μQ材料制作的无中心柱配对罐形磁心详细的测试电路和方法。如图一电路所示,利用LC组成的150KHz低通滤波器在高电平输入的情况下测量磁心产生的非线性失真。这种相对比较的实用方法,专用于无中心柱配对罐形磁心的谐波衰耗测试。 这种磁心主要用于载波电报、电话设备的遥测振荡器和线路放大器系统,其非线性失真有很严格的要求。 图中 ZD —— QF867 型阻容式载频振荡器,输出阻抗 150Ω, Ld47 —— 47KHz 低通滤波器,阻抗 150Ω,阻带衰耗大于61dB, Lg88 ——并联高低通滤波器,阻抗 150Ω,三次谐波衰耗大于61dB Ld88 ——并联高低通滤波器,阻抗 150Ω,三次谐波衰耗大于61dB FD —— 30~50KHz 放大器, 阻抗 150Ω, 增益不小于 43 dB,三次谐波衰耗b3(0)≥91 dB, DP —— Qp373 选频电平表,输入高阻抗, L ——被测无心罐形磁心及线圈, C ——聚苯乙烯薄膜电容器CMO-100V-707APF±0.5%,二只。 测量时,所配用线圈应用丝包铜电磁线SQJ9×0.12(JB661-75)在直径为16.1mm的线架上绕制 120 匝, (线架为一格) , 其空心电感值为 318μH(误差1%) 被测磁心配对安装好后,先调节振荡器频率为 36.6~40KHz, 使输出电平值为+17.4 dB, 即选频表在 22′端子测得的主波电平 (P2)为+17.4 dB,然后在33′端子处测得输出的三次谐波电平(P3), 则三次谐波衰耗值为:b3(+2)= P2+S+ P3 式中:S 为放大器增益dB 从以往的资料引证, 就可以发现谐波失真的测量是一项很精细的工作,其中测量系统的高、低通滤波器,信号源和放大器本身的三次谐波衰耗控制很严,阻抗必须匹配,薄膜电容器的非线性也有相应要求。滤波器的电感全由不带任何磁介质的大空心线圈绕成,以保证本身的“洁净” ,不至于造成对磁心分选的误判。 为了满足多路通信整机的小型化和稳定性要求, 必须生产低损耗高稳定磁心。上世纪 70 年代初,1409 所和四机部、邮电部各厂,从工艺上改变了推板空气窑烧结,出窑后经真空罐冷却的落后方式,改用真空炉,并控制烧结、冷却气氛。技术上采用共沉淀法攻关试制出了μQ乘积 60 万和 100 万的低损耗高稳定材料,在此基础上,还实现了高μ7000~10000材料的突破,从而大大缩短了与国外企业的技术差异。当时正处于通信技术由FDM(频率划分调制)向PCM(脉冲编码调制) 转换时期, 日本人明石雅夫发表了μQ乘积125 万为 0.8×10 ,100KHz)的超优铁氧体材料<3>,其磁滞系数降为优铁
上传时间: 2014-12-24
上传用户:7891
为了改变目前电网现场作业管理的变电巡检、变电检修试验、输电线路巡检检修等管理系统各自独立运行,信息不能共享,功能、效率受限,建设和维护成本高的现状,提出了采用B/S+C/S构架模式,将各现场作业管理模块和生产MIS(管理系统)集成为一体的现场作业管理系统的设计方案,做到各子系统和生产MIS软硬资源共享,做到同一数据唯一入口、一处录入多处使用。各子系统设备人员等基础信息来源于生产管理系统,各子系统又是生产管理系统的作业数据、缺陷信息的重要来源。经过研究试用成功和推广应用,目前该系统已在江西电网220 kV及以上变电站全面应用。 Abstract: In order to improve the status that the substation field inspection system, substation equipments maintenance and testing system, power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency, and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode, integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS,the field work data of the sub systems are the source information of MIS, by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing, this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上传时间: 2013-11-15
上传用户:han_zh
Designing Boards with Atmel AT89C51,AT89C52, AT89C1051, and AT89C2051 for Writing Flash at In-Circuit Test. Recent improvements in chips and testers have made it possible for the tester to begin taking over the role tradi-tionally assigned to the PROM program-mer. Instead of having a PROM pro- grammer write nonvolatile memories before assembling the board, the in-cir- cuit tester writes them during in-circuit testing operations. Many Teradyne Z18- series testers are now in use loading code into nonvolatile memories, micro- controllers and in-circuit programmable logic devices. The purpose of this note is to explain how the Z18 approaches the writing task for Atmel AT89C series IC’s, so that designers of boards using these chips can get the best results.
上传时间: 2013-11-17
上传用户:xiaozhiqban
以C8051F020为核心处理器,设计无线传感器网络数据采集系统。系统采用SZ05-ADV型无线通讯模块组建Zigbee无线网络,结合嵌入式系统的软硬件技术,完成终端节点的8路传感器信号的数据采集。现场8路信号通过前端处理后,分别送入C8051F020的12位A/D转换器进行转换。经过精确处理、存储后的现场数据,通过Zigbee无线网络传送到上位机,系统可达到汽车试验中无线测试的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module,set up a Zigbee wireless network, combined with hardware and software technologies of embedded systems,completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage,the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
标签: C8051F020 Zigbee 汽车测试 系统设计
上传时间: 2013-11-23
上传用户:dsgkjgkjg
飞机电网故障时,机载电气盒必须在延迟时间内切断电网,保护机载设备。采用AT89S52设计的电气盒测试仪能够测试电气盒保护功能,测量延迟时间。实际应用结果表明,该测试仪具有测量准确、可靠性高、成本低等优点。 Abstract: The helicopter-electrical-box must shut off the helicopter power,protect the equipments of the helicopter when the helicopter power is failed.The tester for the helicopter-electrical-box based on AT89S52is used for testing the protect-ing function and measuring the delay time.Application results show this tester has some advantages,such as accurate mea-surement,high dependability,economical cost etc.
上传时间: 2014-12-27
上传用户:786334970
介绍基于ISA总线与KH-9300的数据采集板卡的设置,详细说明8254定时计数器及8259中断控制器的结构特点、工作方式、控制字等,探讨中断类型、中断处理程序、中断矢量表及其填写。重点讲述使用TorboC编写中断服务程序的方法,应注意的主要问题及程序测试的结果。 Abstract: The settings of KH-9300 data acquisition board based on the ISA bus is introduced,the structural characteristics,working methods,control characters of the timing counter 8254 and interruptioncontroller 8259 are explained in detail.The interruption type,interrupt handling programs,interruption vector table and its filling also are discussed.Further,great emphasis is put on the method of interrupt service program compiled by Torbo C,the main issues that should be noted,and the results of program testing.
上传时间: 2013-11-14
上传用户:qq527891923
该系统由单片机89S52控制模块,程控宽带放大模块,整形模块,FPGA内频率、相位差测量模块等构成,采用等精度测频法测出频率和周期,可测量有效值为0.01~5V,频率范围1Hz~20MHz信号的频率、周期信号,精度高达10-6。采用计数法测量相位差,该系统可测量有效值0.5~5V,频率10Hz~100kHz信号的相位差,精度为1°。系统功能由按键控制,测量结果实时显示,人机界面友好。 Abstract: The system consists of the following functional blocks:89S52microcontroller controlling module,programmable amplifier module,comparator module,frequency and phase difference testing module in the FPGA.The system use the equal accuracy frequency-examining technique it measures frequency and circle of signal which its ranges is from1Hz to20MHz and the amplitude of which its range is from0.01Vrms to5Vrms,precision is up to10-6.Using of count method,the system detects the phase difference of signal,the amplitude of whic its range is from0.5Vrms to5Vrms and the frequency of which its ranges is from10Hz to100kHz,precision is up to1°,The system functions is controlled by certain keys,measurement results are displayed in real-time and it is friendly interface.
上传时间: 2013-11-04
上传用户:CHINA526
为了解决磁放大器性能测试过程中,需要对其供给不同数值恒定电流的问题,设计了一种基于DAC7512和单片机的数控恒流源系统。该系统采用AT89C51作为主控器件,将计算机发送的电流控制字命令转换为D/A转换器控制字,通过模拟SPI通信接口,写D/A控制字到DAC7512,从而控制其输出相应数字电压值,经差动缩放电路、电压/电路变换电路和功率驱动电路,最后输出恒定电流。实验结果表明,恒流源输出电流调节范围为-45~+45 mA、精度为±0.1 mA,分辨率达0.024 4 mA,具有应用灵活,外围电路简单,可靠性高的特点。该数控直流恒流源也可为相关产品的测试系统研发提供参考。 Abstract: In order to solve the need to supply different values constant current for the magnetic amplifier in testing process, numerical control constant current source system was designed based on DAC7512 chip and microcontroller technology. The system used the AT89C51 as the main chip, which can convert the current control word from computer into to D/A control words. And the system wrote D/A control word into the DAC7512 chip to control the output voltage value by the SPI communication interface, which can output corresponding constant current figures by scaling circuit, the V/I converter and power drive circuit. Experimental results show that the current source output current adjustment range is -45~+45mA, accuracy is ± 0.1mA, and resolution ratio is 0.024 4mA
上传时间: 2014-12-27
上传用户:invtnewer