switch config tool for configuring kernel mode switch phy driver in openwrt. uses generic netlink for kernel to use communication.
标签： switch configuring generic openwrt
上传时间： 2017-01-04
上传用户：妄想演绎师
CR6221 combines a dedicated current mode PWM controller with a high voltage power MOSFET. It is opti
上传时间： 2013-04-24
上传用户：brucewan
CR6228 combines a dedicated current mode PWM controller with a high voltage power MOSFET. It is opti
上传时间： 2013-05-17
上传用户：natopsi
Top switch ic
上传时间： 2013-06-06
上传用户：eeworm
专辑类-开关电源相关专辑-119册-749M Top-switch-ic-58页-1.2M.pdf
标签： Top-switch-ic 1.2 58
上传时间： 2013-07-10
上传用户：jingfeng0192
implemention of FPGA and DSP linking port, using Asynchronous mode
标签： implemention Asynchronous linking using
上传时间： 2013-08-22
上传用户：fhjdliu
Industrial remote monitoring systems and keep-alivecircuits spend most of their time in standby mode. Manyof these systems also depend on battery power, so powersupply effi ciency in standby state is very important tomaximize battery life. The LT®8410/-1 high effi ciencyboost converter is ideal for these systems, requiringonly 8.5μA of quiescent current in standby mode. Thedevice integrates high value (12.4M/0.4M) output feedbackresistors, signifi cantly reducing input current whenthe output is in regulation with no load. Other featuresinclude an integrated 40V switch and Schottky diode,output disconnect with current limit, built in soft-start,overvoltage protection and a wide input range, all in atiny 8-pin 2mm × 2mm DFN package.
上传时间： 2013-11-23
上传用户：新手无忧
HT66F40使用SIM SPI Mode的用法 HT66F40 内建有串行接口功能，其中包括了SPI 和I2C 这两种总线模式，本文以HT66F40为母体，介绍使用SPI 进行数据传输的方法和注意事项。
上传时间： 2013-10-12
上传用户：tuilp1a
The PCA9549 provides eight bits of high speed TTL-compatible bus switching controlledby the I2C-bus. The low ON-state resistance of the switch allows connections to be madewith minimal propagation delay. Any individual A to B channel or combination of channelscan be selected via the I2C-bus, determined by the contents of the programmable Controlregister. When the I2C-bus bit is HIGH (logic 1), the switch is on and data can flow fromPort A to Port B, or vice versa. When the I2C-bus bit is LOW (logic 0), the switch is open,creating a high-impedance state between the two ports, which stops the data flow.An active LOW reset input (RESET) allows the PCA9549 to recover from a situationwhere the I2C-bus is stuck in a LOW state. Pulling the RESET pin LOW resets the I2C-busstate machine and causes all the bits to be open, as does the internal power-on resetfunction.
上传时间： 2014-11-22
上传用户：xcy122677
产品概述HP ProCurve Switch 2810系列包括两款机型：带有 20个10/100/1000端口的24端口HP ProCurve Switch 2810-24G和带有44个10/100/1000端口的48端口HP ProCurve Switch 2810-48G。每款交换机还配有4个双功能定制端口，可用于RJ-45 10/100/1000或mini-GBIC光纤千兆连接。2810系列交换机可提供出色的访问安全性、高级优先化和流量监控能力，因而是高性能、安全10/100/1000连接的理想选择。此外，它还价格经济、简单易用，带有1U可堆叠外形，即使应用于更小的布线室内，也便于灵活操作。
上传时间： 2013-11-24
上传用户：tiantwo
