The LTC®4151 is a high side power monitor that includesa 12-bit ADC for measuring current and voltage, as wellas the voltage on an auxiliary input. Data is read throughthe widely used I2C interface. An unusual feature in thisdevice is its 7V to 80V operating range, allowing it to coverapplications from 12V automotive to 48V telecom.
上传时间： 2013-10-29
上传用户：集美慧
High voltage buck DC/DC controllers such as the LTC3890(dual output) and LTC3891 (single output) are popular inautomotive applications due to their extremely wide 4V to60V input voltage range, eliminating the need for a snubberand voltage suppression circuitry. These controllersare also well suited for 48V telecom applications whereno galvanic isolation is required.
上传时间： 2013-10-31
上传用户：wwwe
AN22 details the theoretical and application aspects of the LT1088 thermal RMS/DC converter. The basic theory behind thermal RMS/DC conversion is discussed and design details of the LT1088 are presented. Circuitry for RMS/DC converters, wideband input buffers and heater protection is shown.
上传时间： 2013-10-16
上传用户：china97wan
In an increasing trend, telecommunications, networking,audio and instrumentation require low noise power supplies.In particular, there is interest in low noise, lowdropout linear regulators (LDO). These components powernoise-sensitive circuitry, circuitry that contains noisesensitiveelements or both. Additionally, to conserve power,particularly in battery driven apparatus such as cellulartelephones, the regulators must operate with low input-tooutputvoltages.1 Devices presently becoming availablemeet these requirements (see separate section, “A Familyof 20mVRMS Noise, Low Dropout Regulators”).
上传时间： 2013-10-30
上传用户：yeling1919
The LTM8020, LTM8021, LTM8022 and LTM8023 μModule®regulators are complete easy-to-use encapsulated stepdownDC/DC regulators intended to take the pain and aggravationout of implementing a switching power supplyonto a system board. With a μModule regulator, you onlyneed an input cap, output cap and one or two resistorsto complete the design. As one might imagine, this highlevel of integration greatly simplifi es the task of printedcircuit board design, reducing the effort to four categories:component footprint generation, component placement,routing the nets, and thermal vias.
上传时间： 2014-01-18
上传用户：laomv123
功能简述：本控制器采用微控制器控制，其功能如下：1． 12V/24V 蓄电池自动识别2． 自动开关灯智能感知外界光线，天黑时延时自动开启路灯，天亮时自动关闭路灯3． 自动充放电（以12V 蓄电池为例）进入白天后太阳能电池板电压高于蓄电池电压时自动进入充电状态，充电至蓄电池电压高于14.4V 就进入涓流状态充电。而当天黑且蓄电池电压高于10.6V 就允许向LED 放电。4． 蓄电池保护（以12V 蓄电池为例）：当蓄电池电压低（低于10.6V）时，会自动关闭路灯，防止过放，以保护电池。当电池充满（14.4V）时，会停止其他充电状态，而进入涓流充充电状态，以防止过充。5． 采用PWM 调光技术对LED 路灯进行调光，可以和各种可调光恒流源匹配工作。6． 为了节能而调光，可以有各种节能调光模式，以实现不同程度的节能。
上传时间： 2013-11-07
上传用户：wyc199288
为了改变目前电网现场作业管理的变电巡检、变电检修试验、输电线路巡检检修等管理系统各自独立运行，信息不能共享，功能、效率受限，建设和维护成本高的现状，提出了采用B/S+C/S构架模式，将各现场作业管理模块和生产MIS（管理系统）集成为一体的现场作业管理系统的设计方案，做到各子系统和生产MIS软硬资源共享，做到同一数据唯一入口、一处录入多处使用。各子系统设备人员等基础信息来源于生产管理系统，各子系统又是生产管理系统的作业数据、缺陷信息的重要来源。经过研究试用成功和推广应用，目前该系统已在江西电网220 kV及以上变电站全面应用。 Abstract: In order to improve the status that the substation field inspection system， substation equipments maintenance and testing system， power-line inspection and maintenance system are running independent with each other. They can?蒺t share the resource information which accordingly constrains their functions and efficiency， and their construction and maintenance costs are high. This paper introduces a field standardized work management system based on B/S+C/S mode， integrating all field work management systems based on MIS and share the equipments and employee?蒺s data of MIS，the field work data of the sub systems are the source information of MIS， by which the same single data resouce with one-time input can be utilized in multiple places. After the research and testing， this system is triumphantly using in all 220kV and above substations in Jiangxi grid.
上传时间： 2013-11-15
上传用户：han_zh
IC 特色 : ˙ 半谐振模式之 ZVS零电压切换 , 能有效降低切换损失 , 提高效率 , 并具展频功能 , 改善EMI . ˙ 轻 / 重载的 Duty Factor 皆在 CCM 与 DCM 边缘 , 是最能发挥次级 "同步整流" 效率的一种工作模式 . ˙ 空载时进入 Cycle Skipping ( Typical 0.3W ) , 有效达成环保规範 . ˙ 内建 "LEB前缘遮没" 功能 , 避免电流迴授失真 . ˙ 能随输入电压变化 , 自动补偿 OPP过功率保护点 . ˙ 精密的 OVP 过压保护点可自行设定 . ˙ 完整的保护功能 : OVP过压保护 , OCP过流保护 , OPP过载保护 , SWP线圈短路保护 , SCP输出短路保护 , OTP过温度保护 .
上传时间： 2014-12-24
上传用户：回电话#
传统电源电路检修 二、开关电源电路检修 •首先应检查F601、F602两个保险丝。 •若F601或F602熔断，有可能是保险丝本身质量不好，但换上新保险丝后再次熔断，说明电路有电流过大故障. •若F601再次熔断，有可能是整流管V601、V602击穿。 •若F602再次熔断，有可能是稳压输出12V的负载过流，也可能是调整管V603、V605的c-e极击穿。 •若保险丝好，再检查18V直流电压。无18V电压，则有可能是电源变压器绕组开路、或电源开关S601接触不良，或V601、V602整流管都开路。 若18V正常，则无12V输出电压的原因可能是R601、R602开路，C604、C605击穿，或V603、V605开路
上传时间： 2013-11-18
上传用户：蠢蠢66
Sensing and/or controlling current flow is a fundamental requirement in many electronics systems, and the tech-niques to do so are as diverse as the applications them-selves. This Application Note compiles solutions to cur-rent sensing problems and organizes the solutions by general application type. These circuits have been culled from a variety of Linear Technology documents
标签： 电流检测电路
上传时间： 2013-10-22
上传用户：moshushi0009
