mcu与cpld之间spi接口程序，mcu为master，cpld用verilog写成slave模块
上传时间： 2013-08-14
上传用户：1039312764
关于FPGA流水线设计的论文\r\nThis work investigates the use of very deep pipelines for\r\nimplementing circuits in FPGAs, where each pipeline\r\nstage is limited to a single FPGA logic element (LE). The\r\narchitecture and VHDL design of a parameterized integer\r\na
上传时间： 2013-09-03
上传用户：wl9454
The trend in ADCs and DACs is toward higher speeds and higher resolutions atreduced power levels. Modern data converters generally operate on ±5V (dualsupply) or +5V (single supply). In fact, many new converters operate on a single +3Vsupply. This trend has created a number of design and applications problems whichwere much less important in earlier data converters, where ±15V supplies and ±10Vinput ranges were the standard.
上传时间： 2013-11-16
上传用户：sjw920325
The MAX17600–MAX17605 devices are high-speedMOSFET drivers capable of sinking /sourcing 4A peakcurrents. The devices have various inverting and noninvertingpart options that provide greater flexibility incontrolling the MOSFET. The devices have internal logiccircuitry that prevents shoot-through during output-statchanges. The logic inputs are protected against voltagespikes up to +14V, regardless of VDD voltage. Propagationdelay time is minimized and matched between the dualchannels. The devices have very fast switching time,combined with short propagation delays (12ns typ),making them ideal for high-frequency circuits. Thedevices operate from a +4V to +14V single powersupply and typically consume 1mA of supply current.The MAX17600/MAX17601 have standard TTLinput logic levels, while the MAX17603 /MAX17604/MAX17605 have CMOS-like high-noise margin (HNM)input logic levels. The MAX17600/MAX17603 are dualinverting input drivers, the MAX17601/MAX17604 aredual noninverting input drivers, and the MAX17602 /MAX17605 devices have one noninverting and oneinverting input. These devices are provided with enablepins (ENA, ENB) for better control of driver operation.
上传时间： 2013-12-20
上传用户：zhangxin
The LTC®1966 is a true RMS-to-DC converter that uses aDS computational technique to make it dramatically simplerto use, significantly more accurate, lower in powerconsumption and more flexible than conventional logantilogRMS-to-DC converters. The LTC1966 RMS-to-DCconverter has an input signal range from 5mVRMS to1.5VRMS (a 50dB dynamic range with a single 5V supplyrail) and a 3dB bandwidth of 800kHz with signal crestfactors up to four.
上传时间： 2013-10-12
上传用户：qilin
The 14-bit LTC2351-14 is a 1.5Msps, low power SARADC with six simultaneously sampled differential inputchannels. It operates from a single 3V supply and featuressix independent sample-and-hold amplifi ers and a singleADC. The single ADC with multiple S/HAs enables excellentrange match (1mV) between channels and channel-tochannelskew (200ps).
上传时间： 2014-12-23
上传用户：天诚24
A fully differential amplifi er is often used to converta single-ended signal to a differential signal, a designwhich requires three signifi cant considerations: theimpedance of the single-ended source must match thesingle-ended impedance of the differential amplifi er,the amplifi er’s inputs must remain within the commonmode voltage limits and the input signal must be levelshifted to a signal that is centered at the desired outputcommon mode voltage.
上传时间： 2013-11-09
上传用户：wweqas
Recent advances in low voltage silicon germaniumand BiCMOS processes have allowed the design andproduction of very high speed amplifi ers. Because theprocesses are low voltage, most of the amplifi er designshave incorporated differential inputs and outputs to regainand maximize total output signal swing. Since many lowvoltageapplications are single-ended, the questions arise,“How can I use a differential I/O amplifi er in a single-endedapplication?” and “What are the implications of suchuse?” This Design Note addresses some of the practicalimplications and demonstrates specifi c single-endedapplications using the 3GHz gain-bandwidth LTC6406differential I/O amplifi er.
上传时间： 2013-11-23
上传用户：rocketrevenge
Application considerations and circuits for the LT1001 and LT1002 single and dual precision amplifiers are illustrated in a number of circuits, including strain gauge signal conditioners, linearized platinum RTD circuits, an ultra precision dead zone circuit for motor servos and other examples.
上传时间： 2013-10-18
上传用户：dreamboy36
This reference design (RD) features a fullyassembled and tested surface-mount printed circuitboard (PCB). The RD board utilizes the MAX48851:2 or 2:1 multiplexer and other ICs to implement acomplete video graphics array (VGA) 8:1multiplexer.VGA input/output connections are provided to easilyinterface the MAX4885 RD board with VGAcompatibledevices. The RD board gives the optionto use a single 5V DC power supply (V+), or this RDboard can be powered from any one of the eight VGA sources.
标签： multiplexer reference VGA
上传时间： 2013-11-09
上传用户：ANRAN
