针对科研实验中对拉压千斤顶加载过程控制的需要，采用ATmega128单片机控制步进电机进而实现对执行系统的电动泵站实行自动控制。对力和位移的数据采集与处理及用步进电机控制电动泵站手柄的技术细节作了重点描述。通过单片机的A/D变换器对AMP放大模块采集的电桥信号作量化处理，千斤顶的操控手柄位置依电动油泵阀门开启的方向和大小作若干定位，单片机根据力或位移传感器信号，实时控制步进电机驱动手柄旋转到相应操控位置。 Abstract: This article describes the use of ATmega128 AVR microcontroller series of DBS electric pumping stations and QF100/200 separate twoway hydraulic jack to automate the process of manipulating the work of the technical content. Articles on force and displacement data acquisition and processing， and stepper motor control electric pump with the handle of the key technical details were described. Through the MCU’s A / D converter module is collected on the AMP amplification quantify the signal bridge， jack handle position control valve opening according to the direction of electric pumps for a number of positioning and size of the microcontroller based on force or displacement sensor signals， real-time control stepper motor drive control handle rotate to the appropriate location.
上传时间： 2014-01-16
上传用户：hasan2015
便携式信号采集在机器健康诊断系统中有较高的应用价值。机器健康诊断的信号特点是包括低频信号。本文研究是为了实现简易而且低成本的低频便携式信号采集。以Microchip公司单片机PIC18F1320为核心设计信号采集电路，实现了信号的采集和保存。系统采用串行电可擦除芯片24LC32A保存数据，经过有线通信，信号数据由串行口通过MAX232芯片输送到微型计算机接收和保存，最后绘制出信号波形。 微型计算机程序采用Visual Basic编程。研究成功采样频率为3 kHz的复杂信号，证明该方案符合设计要求。 Abstract: Portable signal acquisition is useful in machine health monitoring systems. The signal characteristics of machine health monitoring includes low frequency signals. The goal of this study is to realize simple, inexpensive and portable low frequency signal sampling. This paper provides the project of signal acquisition system design based on PIC18F1320 microcontroller manufactured by the Microchip Technology Incorporation to achieve signal sampling and storage. The system adopted EEPROM 24LC32A to store the signal data. The microcomputer received data via wired link with the MAX232 IC through the serial port. The microcomputer program, programmed in Visual Basic, received the data, stored it and plotted the signal. The study successfully samples 3kHz complicated signals and thus meets the design requirement.
上传时间： 2013-11-19
上传用户：moerwang
针对目前使用的RS232接口数字化B超键盘存在PC主机启动时不能设置BIOS，提出一种PS2键盘的设计方法。基于W78E052D单片机，采用8通道串行A/D转换器设计了8个TGC电位器信息采集电路，电位器位置信息以键盘扫描码序列形式发送，正交编码器信号通过XC9536XL转换为单片机可接收的中断信号，软件接收到中断信息后等效处理成按键。结果表明，在满足开机可设置BIOS同时，又可实现超声特有功能，不需要专门设计驱动程序，接口简单，成本低。 Abstract: Aiming at the problem of the digital ultrasonic diagnostic imaging system keyboard with RS232 interface currently used couldn?蒺t set the BIOS when the PC boot， this paper proposed a design method of PS2 keyboards. Based on W78E052D microcontroller，designed eight TGC potentiometers information acquisition circuit with 8-channel serial A/D converter， potentiometer position information sent out with keyboard scan code sequentially.The control circuit based on XC9536 CPLD is used for converting the mechanical actions of the encoders into the signals that can be identified by the MCU， software received interrupt information and equivalently treatmented as key. The results show that the BIOS can be set to meet the boot， ultrasound specific functionality can be achieved at the same time， it does not require specially designed driver，the interface is simple and low cost.
上传时间： 2013-10-10
上传用户：asdfasdfd
以C8051F020为核心处理器，设计无线传感器网络数据采集系统。系统采用SZ05-ADV型无线通讯模块组建Zigbee无线网络，结合嵌入式系统的软硬件技术，完成终端节点的8路传感器信号的数据采集。现场8路信号通过前端处理后，分别送入C8051F020的12位A/D转换器进行转换。经过精确处理、存储后的现场数据，通过Zigbee无线网络传送到上位机，系统可达到汽车试验中无线测试的目的。 Abstract: This paper designs a wireless sensor network system for data acquisition with C8051F020 as core processors.The system used SZ05-ADV wireless communication module，set up a Zigbee wireless network， combined with hardware and software technologies of embedded systems，completed the end-node 8-locale sensor signal data acquisition.Eight locale signals were sent separately into the 12-bit ADC of C8051F020 for conversion through front treatment.After accurate processing and storage，the locale data was transmitted to the host computer through Zigbee wireless.The system achieves the purpose of wireless testing in vehicle trial.
标签： C8051F020 Zigbee 汽车测试 系统设计
上传时间： 2013-11-23
上传用户：dsgkjgkjg
提出了一种以S3C2440A为核心处理器的银行评价器的设计方案，并结合XILINX公司的XL95144XL型CPLD，辅助S3C2440A，实现该银行评价器的各部分功能以及系统信号之间的相互协调。该评价器在系统设计上采用液晶屏显示，代替了以往简单的数码管电路的显示模式，在视觉上给人以全新的享受。同时，评价器增加了新的网络供电方式，只要将评价器连接上网络就可以正常工作，方便了客户的使用。总之，此款银行评价器采用了嵌入式系统的设计方案，大大丰富了系统功能，实现一个银行评价器设计的新突破。 Abstract: S3C2440A of SamSung company is the core component of the embedded system. A design of bank assessor based on S3C2440A was provided in this paper. It used XL95144XL combined with S3C2440A to realize all the functions and coordination with system signals. This bank assessor used LCD to display instead of the former simple digital display and provided a new seusuous enjoment. Meanwhile，it provided a new method of network power supply，that the bank assessor could regularly work once it connected to the network，which is convenient for customers to use. In a word，this assessor takes embedded system，enriches the system’s functions and reclizes a new breakout.
标签： S3C2440A
上传时间： 2013-11-03
上传用户：taa123456
单片机作为一种微型计算机，其内部具有一定的存储单元（8031除外），但由于其内部存储单元及端口有限，很多情况下难以满足实际需求。为此介绍一种新的扩展方法，将数据线与地址线合并使用，通过软件控制的方法实现数据线与地址线功能的分时转换，数据线不仅用于传送数据信号，还可作为地址线、控制线，用于传送地址信号和控制信号，从而实现单片机与存储器件的有效连接。以单片机片外256KB数据存储空间的扩展为例，通过该扩展方法，仅用10个I/O端口便可实现，与传统的扩展方法相比，可节约8个I/O端口。 Abstract: As a micro-computer,the SCM internal memory has a certain units(except8031),but because of its internal storage units and the ports are limited,in many cases it can not meet the actual demand.So we introduced a new extension method,the data line and address lines combined through software-controlled approach to realize the time-conversion functions of data lines and address lines,so the data lines not only transmited data signals,but also served as address lines and control lines to transmit address signals and control signals,in order to achieve an effective connection of microcontroller and memory chips.Take microcontroller chip with256KB of data storage space expansion as example,through this extension method,with only10I/O ports it was achieved,compared with the traditional extension methods,this method saves8I/O ports.
上传时间： 2014-12-26
上传用户：adada
介绍了采用ATmega48单片机实现三相无刷直流电机控制器的方法。利用Atmega48获得带死区的脉宽调制（PWM）、霍尔传感器的换相处理、正弦驱动信号的产生和电机转速的控制等功能。采用该方法的优点是所需的外围器件少，成本低。 Abstract: The method of 3-phase brushless DC motor control based on ATmega48 is presented in this paper.The system uses ATmega48 to generate PWM signals with dead-time, hall sensors signals commutation，sine driving signal and rotational speed of motor.Using this method，the needed external devices are few, the cost is low.
上传时间： 2013-12-09
上传用户：330402686
介绍了一种基于C8051F020单片机的多路压力测量仪。该测量仪选用电阻应变式压力传感器采集压力信号，并经放大电路处理后送入C8051F020单片机，再由C8051F020单片机内部的A/D转换器将采集到的压力信号进行模数转化，然后分别对数据进行存储和显示。该测量仪能测量6路压力信号，并且各测量点都能单独检测和设置。由于采用了C8051F020单片机，简化了硬件电路，增强了抗干扰能力，使得测量仪具有测量精度高，冲击小等特点。 Abstract: A measurement apparatus for multi-channel pressure based on single chip microcomputer is introduced.It can measure 6 channels signal of the pressure，and the pressure measure points can be detection and located individually.The pressure signal sampling is obtained by resistor stress-type pressure sensors，the digital signals of 6 channels are collected through amplifying and adjustment circuit of pressure signals and internal integrated A/D converter of MCU.Finally，and it realizes the function to store and display data separately.C8051F020 was used to made hardware circuit simple，and it also enhanced the anti-interference ability.It features high precision and little impact.
上传时间： 2013-11-16
上传用户：yare
介绍一种简单射频识别系统设计。该设计包括阅读器、应答器和线圈3部分。由单片机控制阅读器向应答器发射无线信号，并接收应答器回送的信号，再通过分析回送信号识别物品。阅读器和应答器之间以半双工通信方式通信。 Abstract: A simple design of radio frequency identification system is given in this paper.The design includes reader,responder and winding.Through MCU，signals are sent to responder from reader，then corresponding signals are sent back. According to the analysis of the signals sent back，the objects can be identified.Half-duplex communication is adopted? between? reader? and? responder.
上传时间： 2013-10-11
上传用户：plsee
针对材料试验机等设备中要求测量或控制材料拉伸或压缩的位移，一般采用光电轴角编码器检测位置信号，输出正交编码脉冲信号。若采用其他方法检测位置信号，必然导致电路设计复杂，可靠性降低。因此，提出一种基于LS7266R1的电子式万能材料试验机设计方案。给出了试验机中的控制器工作原理，LS7266R1与单片机的接口硬件设计，以及主程序软件流程图。巧妙地把力量传感器，位移传感器等机械运动状态的压力或拉力以及位置坐标，变成了电压信号和电脉冲数字信号，供A/D测量和LS7266R1计数，从而实现了独立完成材料试验控制或通过PC机串口命令完成材料试验控制。 Abstract: Aiming at the requirement that the displacement of the tension and compression always be tested and controlled in the equipement such as material testing machine. The position signal was tested by photoelectric axial angle coder. Therefore， the paper proposes the design of electronic universal testing machine design based on LS7266R1. If the position signal detected by other methods， will inevitably lead to the circuit design complexity， reliability decreased. The work theory of the controller， the hardware interface design between LS7266R1 and single chip， and the flow chart of main program， are presented in this paper. The signal of the compression or tension power and displacement at working， which tested by power sensor and displacement sensor especially， is changed into electric voltage and electric pulse numerical signals. And these signals can be tested by A/D and counted by LS7266R1. Finally the test of the material properties can be controlled by itself， or controlled by the COM command of PC.
上传时间： 2013-11-02
上传用户：yl1140vista
