本系统采用电动机电枢供电回路串接采样电阻的方式来实现对小型直流有刷电动机的转速测量。该系统主要由二阶低通滤波电路,小信号放大电路、单片机测量显示电路、开关稳压电源电路等组成。同时自制电机测速装置,用高频磁环作为载体,用线圈绕制磁环,利用电磁感应原理检测电机运行时的漏磁,将变化的磁场信号转化为磁环上的感应电流。用信号处理单元电路将微弱电信号转化为脉冲信号,送由单片机检测,从而达到准确测量电机的速度的要求。In this system, the sampling resistance of armature power supply circuit is connected in series to measure the speed of small DC brush motor. The system is mainly composed of second-order low-pass filter circuit, small signal amplifier circuit, single-chip measurement and display circuit, switching regulated power supply circuit and so on. At the same time, the self-made motor speed measuring device uses high frequency magnetic ring as the carrier, coil winding magnetic ring, and electromagnetic induction principle to detect the leakage of magnetic field during the operation of the motor, which converts the changed magnetic field signal into the induced current on the magnetic ring. The weak electric signal is transformed into pulse signal by signal processing unit circuit, which is sent to single chip computer for detection, so as to meet the requirement of accurate measurement of motor speed.
标签： 直流电动机
上传时间： 2022-03-26
上传用户：
实验教学一直是工科教学中不可或缺的组成部分,对培养学生的动手能力,独立思考能力,创新思维与发散思维具有重要的作用。针对目前电路教学实验中电路仿真实验与实物电路实验各自独立,无法统一问题,提出将仿真电路实验与实物电路实验有机的结合同步操作,并使用Web发布实现远程实验操作。采用Multisim作为电路实验仿真平台,NI Eiviss II作为实物电路实验硬件平台,运用LabVIEW整合Multisim电路仿真实验与实物电路实验,实现仿真与实物实验有机结合,两种实验可同步进行。学生在仿真实验中先可探索实验,然后做实物实验。同时运用LabVIEW开发出实验过程人机交互操作接口界面,使用过程中效果良好。Experimental teaching has always been an indispensable part of engineering education.And it always plays an important role in cultivating students'practical ability,independent thinking ability,innovative thinking and divergent thinking.But simulation experiment and physical experiment cannot be unified in the circuit teaching experiment at present.In order to solve this problem,this paper proposes to combine organically the simulation circuit experiment with physical circuit experiment,and synchronously operate them.This paper uses the WEB publishing to achieve remote experimental operation.Multisim is used as the circuit simulation platform,and NI Eiviss II is used as the physical circuit hardware platform.Multisim circuit simulation experiment and physical circuit experiment are implemented by LabVIEW to realize the combination of simulation experiment and physical experiment.Students do explore experiments in simulation experiment firstly,and then do physical experiment.And this paper uses LabVIEW to develop the experimental man-machine interface.
上传时间： 2022-04-05
上传用户：
German universities and scientists have repeatedly set the intermational standard in drive technology. Identification and active compensation of natural frequencies in oscillatory mechanics, status controls with monitoring structures incorporating acceleration sensors, adaptive compensation of measurement system deficiencies, self-adjusting detent torque compensation… everything invented with only a single aim in mind: to continue improv-ing the motion control, dynamics, precision and processing speed of your machines. For the industrial applicabability of this technology scientific publications in proceedings and laboratory test rigs are not enough. These features consequenty need to be converted into cost-efficient and easily manageable products. That 's exactly what we have done.So in future, if you should need more than today ' smarket can offer you, now everything isgoing to be alright. With our new high-performance ServoOne drive series you will experi-ence
标签： servoone
上传时间： 2022-06-24
上传用户：kingwide
陀螺仪硬件自检：相关方法陀螺仪允许用户测试机械和电气部分。自检的代码在 InvenSense提供的 MotionApps™软件里面。如果没有使用 MotionApps™软件，请参阅下节(Obtaining the Gyroscope Factory Trim (FT) Value)。当自检启动，片上的电子设备就会启动相应的传感器。这次启动会使传感器的 proofmasses的距离相当于一个预定的科里奥利力（Coriolis force）。传感器的 Proof masses位移变换的结果将在输出信号中反映。输出信号用户可以在自检反馈看到。自检反馈（STR）定于如下：Self Test Response=Gyroscope Output with Self Test Enabled — Gyroscope Output with Self Test Disabled自检反馈通过反馈与出产的评估比较查找变换用于确定这部分通过还是自检失败
上传时间： 2022-07-23
上传用户：xsr1983
