The latest release, ver 1.16 of the ARM (7TDMI, 720T, 920T) port for uC/Os-ii V2.61 (and higher) includes ports for the following platforms: 1. S3c2410x ( ARM920T from Samsung ) on SMDK2410 eval board. 2. LPC2xxx - LPC210x & LPC213x ( ARM7TDMI-S from Philips ) on IAR s Kickstart & OLIMEX boards. 3. EP7312 ( ARM720T from CIRRUS ) on CDK238 eval board. Should also work on boards based on the CS89712. Tool-chains: GCC 3.3.2, ADS 1.2 & SDT 2.51. Op-modes: Pure ARM & ARM-THUMB interworked. Endianess: Big endian & Little endian modes
标签： release latest higher Os-ii
上传时间： 2014-01-26
上传用户：小眼睛LSL
Compact Flash Support For Nios II 5.0, To download supporting materials for this new Compact Flash support, download the following .zip file, extract to a computer with Quartus II 5.0 & Nios II 5.0 installed, and proceed to use the hardware and/or software examples of your choice to proceed. Additional information is available in the readme.txt document, included in the top-level of the .zip file
标签： Compact Flash supporting materials
上传时间： 2016-02-13
上传用户：gmh1314
μC/Os-ii Goals Probably the most important goal of μC/Os-ii was to make it backward compatible with μC/OS (at least from an application’s standpoint). A μC/OS port might need to be modified to work with μC/Os-ii but at least, the application code should require only minor changes (if any). Also, because μC/Os-ii is based on the same core as μC/OS, it is just as reliable. I added conditional compilation to allow you to further reduce the amount of RAM (i.e. data space) needed by μC/Os-ii. This is especially useful when you have resource limited products. I also added the feature described in the previous section and cleaned up the code. Where the book is concerned, I wanted to clarify some of the concepts described in the first edition and provide additional explanations about how μC/Os-ii works. I had numerous requests about doing a chapter on how to port μC/OS and thus, such a chapter has been included in this book for μC/Os-ii.
标签： Os-ii compatible important Probably
上传时间： 2013-12-02
上传用户：jkhjkh1982
This designs demonstrates how to use the Ethernet port using a Nios II system on the DE2 board. It sends packets, and using a loopback Ethernet cable, it ll receive the same packets which are then displayed. It also works if the board is connected to another packet source.
标签： demonstrates the Ethernet designs
上传时间： 2013-11-27
上传用户：skfreeman
在μC/Os-ii下，设计了一个通用的设备管理模型，称为通用驱动框架，通过该驱动框架，可以实现对硬件设备的统一、一致的管理，同时，也为上层应用程序提供了统一、一致的设备访问接口，并在以ARM7TDMI-S为核心的LPC2114微控制器开发板上给出了一例实现。
标签： Os-ii
上传时间： 2013-12-20
上传用户：ljt101007
Nios II Custom InstructionUserGuideNios II custom instructions are custom logic blocks adjacent to the ALU in the processor’s data path.
标签： custom InstructionUserGuideNios instructions adjacent
上传时间： 2016-11-16
上传用户：moshushi0009
This tutorial explains how the SDRAM chip on ltera’s DE2 Development and Education board can be used with a Nios II system implemented by using the Altera SOPC Builder.
标签： Development Education tutorial explains
上传时间： 2017-06-15
上传用户：hanli8870
MAX+PLUS II快速入门
上传时间： 2013-04-15
上传用户：eeworm
Max+Plus II 简易用户使用入门
上传时间： 2013-06-15
上传用户：eeworm
从0开始移植UCOS II到野火STM32开发板教程
上传时间： 2013-04-15
上传用户：eeworm
