booth乘法器： 16*16有符号乘法器，Booth编码，简单阵列，ripple Carry Adder
上传时间： 2014-01-16
上传用户：努力努力再努力
16*16有符号乘法器的 编码方式：Booth编码， 拓扑结构：简单阵列 加法器：ripple Carry Adder
上传时间： 2014-01-13
上传用户：com1com2
The AP2406 is a 1.5Mhz constant frequency, slope compensated current mode PWM step-down converter. The device integrates a main switch and a synchronous rectifier for high efficiency without an external Schottky diode. It is ideal for powering portable equipment that runs from a single cell lithium-Ion (Li+) battery. The AP2406 can supply 600mA of load current from a 2.5V to 5.5V input voltage. The output voltage can be regulated as low as 0.6V. The AP2406 can also run at 100% duty cycle for low dropout operation, extending battery life in portable system. Idle mode operation at light loads provides very low output ripple voltage for noise sensitive applications. The AP2406 is offered in a low profile (1mm) 5-pin, thin SOT package, and is available in an adjustable version and fixed output voltage of 1.2V, 1.5V and 1.8V
上传时间： 2017-02-23
上传用户：w124141
The PW2163 is a high efficiency 500 kHz synchronous step-down DC-DC converter capable ofdelivering 3A current. The PW2163 operates over a wide input voltage range from 4.5V to 18V andintegrates main switch and synchronous switch with very low RDS(ON) to minimize the conductionloss. Low output voltage ripple and small external inductor and capacitor sizes are achieved with 500kHz switching frequency. It adopts the instant PWM architecture to achieve fast transient responsesfor high step down applications
标签： pw2163
上传时间： 2022-02-11
上传用户：
The PW2053 is a high-efficiency monolithic synchronous buck regulator using a constantfrequency, current mode architecture. The device is available in an adjustable version. Supply currentwith no load is 40uA and drops to <1uA in shutdown. The 2.5V to 5.5V input voltage range makesthe PW2053 ideally suited for single Li-Ion battery powered applications. 100% duty cycle provideslow dropout operation, extending battery life in portable systems. PWM/PFM mode operationprovides very low output ripple voltage for noise sensitive applications. Switching frequency isinternally set at 1.2MHz, allowing the use of small surface mount inductors and capacitors. Lowoutput voltages are easily supported with the 0.6V feedback reference voltage
标签： pw2053
上传时间： 2022-02-14
上传用户：jason_vip1
为设计高效率、低损耗的PFC电路,本文基于UCC28019进行电路设计。以UCC28019输出的PWM波形来控制Boost升压斩波为核心电路,使电路中的电容交替地充放电、电感交替的储存和释放能量,最后实现在输入AC20V~24V电压情况下稳定输出DC38V。测试结果表明,系统实现效率为95%左右,电压调整率小于1%,电源功率因数0.99。交流输入电压为19.0-25.8 V时,输出直流电压稳定性较好,电感无明显啸叫且纹波小,具有一定的带负载能力和实用性。In order to design the PFC circuit with high efficiency and low loss,this paper designs the circuit based on UCC28019.The PWM waveform output by UCC28019 is used to control boost chopper as the core circuit,which alternately charges and discharges capacitors,stores and releases energy by inductors,and finally achieves stable output of DC38 V under the input voltage of AC20 V~24 V.The test results show that the system achieves about 95% efficiency,the voltage adjustment rate is less than 1%,the power factor is 0.99,and the AC input voltage is 19.0-25.8 V.The output DC voltage stability is good,the inductance has no obvious whistle and the ripple is small,so it has certain load capacity and practicability.
上传时间： 2022-04-03
上传用户：
